Installation Guide

ManualsBrandsUnbranded ManualsFlooring7 in. x 47.75 in. Power Click Fossil Oak Luxury Vinyl Plank (23.2 sq. ft. / case)

POWER CLICK LVT (LUXURY VINYL TILE)/LVP (LUXURY VINYL PLANK) -

FLOORING INSTALLATION GUIDELINES

Before you start read these Installer/Owner Responsibilities:

Before starting installation, it is important you read all instructions and warranty

information. By starting installation of this product you are agreeing that you have read

and understand all installer/owner’s requirements and responsibilities and are aware

that deviating from the instructions and recommendations in this installation guide may

result in voiding the product warranty.

Verify color and finish before installation. Once the floor is installed, it is deemed to have

been inspected, approved and accepted.

It is the sole responsibility of the installer/owner, prior to installation, to assure that the

planned installation area is suitable for LVT/LVP flooring and meets local building

codes. Confirm that all subflooring is dry, sound, flat and meets or exceeds all industry

standards/local building codes; as well as the recommendations listed herein. The

manufacturer accepts no responsibility for product failure extending from or related to

failure to meet job area/environment and subflooring requirements.

The installer/owner assumes full responsibility for the final inspection of this product.

Inspection should be done prior to installation and should include: print/color/texture,

factory finish and locking system. If the product is not acceptable, DO NOT INSTALL IT.

Contact your supplier immediately for assistance. Flooring that has been installed will

be deemed to have been inspected and quality accepted.

If you wish to install over a radiant heating system consult with the manufacturer of your

radiant heating system to ensure that it is compatible with LVT/LVP flooring.

Temperature must never exceed 26° C (79° F) and changes in temperature settings

must be gradual. Rapid temperature changes and/or excessive heat will damage the

flooring and/or the finish. It is the responsibility of installer/owner to confirm the

suitability of the radiant heating system for use with this product. Any damage to the

floor caused by the radiant heating system will not be covered by the product warranty.

Installations in areas of potential rapid temperature change (solariums, sun-rooms,

saunas, etc.) may exceed the temperature limitations of the product and void the

product warranty. Verify the temperature fluctuations prior to installation to determine if

the area is suitable for LVT/LVP flooring.

Product is rated for indoor use only within the required temperature range, do not install

outdoors.

Summary of content (4 pages)

PAGE 1
POWER CLICK LVT (LUXURY VINYL TILE)/LVP (LUXURY VINYL PLANK) FLOORING INSTALLATION GUIDELINES Before you start read these Installer/Owner Responsibilities: Before starting installation, it is important you read all instructions and warranty information.
PAGE 2
Tools required: Safety glasses, utility knife, straight edge, chalk-line, tape measure, pry-bar, saw, spacers. Pre-installation: When calculating flooring square footage requirements, allow a minimum of an additional 10% for cuts, waste and defects. If installing a diagonal or other special pattern, allow for 10% additional materials. Acclimatize LVT/LVP flooring for a minimum of 48 hours.
PAGE 3
CLICK FLOATING GENERAL INSTALLATION INFORMATION:  For a click floating installation, follow the directives noted above regarding sub-floor preparation.  Floating installations may be made over most subfloors including: Plywood or OSB, ceramic/porcelain tile, smooth stone, marble, granite, and linoleum. Do NOT install over carpet.  Using a chalk-line, carefully snap a line between these two points.
PAGE 4
   flooring panel under the doorjamb with the decorative pattern facing upwards. Please note that the floor must be allowed to expand under the doorjamb and recommended expansion gap must be respected. Ensure there is a minimum 1/4” (6mm) gap around the entire floor perimeter and any obstacles. Measure and cut the last panels to fit so that there is a minimum 1/4” (6mm) gap along the last wall. Remove all temporary shims, sweep & vacuum immediately.