UP354BH(WDECT2355+2) OM 5/14/04 12:04 PM Page a WDECT 2355+2 Quick Start Guide Wide Band Digital Technology provides the clearest sound and the best privacy.
UP354BH(WDECT2355+2) OM 5/14/04 10:48 AM Page i INSTALLATION & SAFETY Choosing the best location for your phone. When choosing a location for your phone there are a number of appliances the phone should not be near, and areas you should avoid. AVOID Television sets and other electronic appliances AVOID Moisture CHARGE the new phone for 15 - 20 hrs. AVOID Microwave ovens • This symbol indicates important operating and servicing instructions. AVOID moisture Don’t overload the power outlet.
UP354BH(WDECT2355+2) OM Start Here! 5/14/04 10:48 AM Page ii QUICK START GUIDE This page is a very condensed version of the Owner’s Manual. It is designed to allow you to get your phone installed and operating as quickly as possible however it does not attempt to explain any of the advanced features of the WDECT2355 series. Installing the Base Unit 1) Connect the AC adapter to the DC IN 9V jack and to a standard AC wall outlet.
UP354BH(WDECT2355+2) OM 5/14/04 10:48 AM Page iii 3) Set the base on a desk or tabletop. 4) Raise the antenna to a vertical position. Connecting the charger 1) Connect the AC adapter into the charging cradle and to a AC wall outlet. 2) Set the charger on a desk or tabletop. Installing the battery pack • Charge the handset battery pack for at least 15-20 hours before using your new cordless telephone for the first time.
UP354BH(WDECT2355+2) OM 5/14/04 10:48 AM Page iv Charging the handset(s) 1) Place the handset(s) in the main base unit or charging cradle with the keypad facing forward. Recharge your phone on a regular basis by returning the handset to the base after each phone call. 2) Make sure the charge LED illuminates. If the LED does not illuminate, check to see that the AC adapter is plugged in and that the handset makes good contact with the base charging contacts.
UP354BH(WDECT2355+2) OM 5/14/04 2:20 PM Page v CONTENTS INSTALLATION & SAFETY QUICK START GUIDE CONTENTS GETTING STARTED Controls and Functions Uniden Company Philosophy Welcome Features Checking the Package Contents Terminology Mounting the Base Unit on a Wall Battery Maintenance Installing the Beltclip Headset Installation (Optional) Display and Icons About the Menu Options Setting up the Menu BASICS Making and Receiving Calls Keypad Lock Placing a Call on Hold Redialing a Call Adjusting the Handset R
UP354BH(WDECT2355+2) OM 5/14/04 10:48 AM Page 1 1 6 2 7 3 4 8 14 15 16 17 9 10 5 11 12 13 18 19 20 21 22 Handset Remote Operation (P. 54) (Review ITAD messages from handset) Select/ Repeat Key Delete Key Play Key Skip Key Key 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. 20. 21. 22. Handset Antenna Headset Jack Cover Beltclip Hole Hands-Free Speaker Handset Battery Compartment New Message LED Handset Earpiece LCD Display /del Key /vol/ / Key a. ringer volume control b.
UP354BH(WDECT2355+2) OM 5/14/04 10:48 AM Page 2 Main Base 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 40 41 42 43 44 45 39 46 23. 24. 25. 26. 27. 28. 29. 30. 31. 32. 33. 34. [2] Base Speaker Clock/MENU Key repeat/SELECT Key delete Key Charge LED Message Counter Display In use LED play/stop Key skip/SELECT Key SET Key Memo record Key Ans on/off Key 47 35. 36. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46.
UP354BH(WDECT2355+2) OM 5/14/04 10:48 AM Page 3 UNIDEN COMPANY PHILOSOPHY To bring outstanding wireless communication products to people’s lives throughout the world. WELCOME Congratulations on your purchase of the Uniden Multi-Handset Cordless System telephone. This unit is different from conventional cordless telephones. When the base unit is connected to AC power and a telephone line, it can support up to 4 handsets.
UP354BH(WDECT2355+2) OM 5/14/04 10:48 AM Page 4 FEATURES Great features of this cordless phone include: • Designed and Engineered in Japan • Wide Band Digital Technology • Multi (4) Handset Capable • Digital Duplex Speakerphone on Handset Advanced Alpha Display Caller ID Features: • Alpha Memory Dialling • POP ID - Caller Name Identification* • 20 Individual Caller Allocations • 100 Caller ID* Memories with Phonebook • 3 Line Backlit Full Dot Matrix LCD Display with Clock • Maxi-Sound - Extra Loud Hands
UP354BH(WDECT2355+2) OM 5/14/04 10:48 AM Page 5 CHECKING THE PACKAGE CONTENTS Make sure you have received the following items in the package. If any of these items are missing or damaged, contact your retailer.
UP354BH(WDECT2355+2) OM 5/14/04 10:48 AM Page 6 MOUNTING THE BASE UNIT ON A WALL You can mount your base directly to the wall. Before doing this, consider the following: • Avoid electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. • Mount your phone within distance of a working phone jack. • Make sure the wall material is capable of supporting the weight of the base and handset.
UP354BH(WDECT2355+2) OM 5/14/04 10:48 AM Page 7 BATTERY MAINTENANCE Battery use time (per charge) Fully charged • Up to 7 hours continuous use • Up to 10 days when the handset is in the standby mode (up to 15 hours when in DirectLink mode) Recharge your phone on a regular basis by returning the handset to the charger after each phone call. Low battery alert When the batteries are very low and need to be charged, the phone is programmed to eliminate functions in order to save power.
UP354BH(WDECT2355+2) OM 5/14/04 10:48 AM Page 8 Battery replacement and handling When the operating time becomes short, even after a battery is recharged, please replace the battery. With normal usage, your battery should last about one year. Please contact your place of purchase or the Uniden Parts Department for a replacement battery. • • • • Caution Use only the specified Uniden battery pack (BT-446). Do not remove the batteries from the handset to charge them.
UP354BH(WDECT2355+2) OM 5/14/04 10:49 AM Page 9 HEADSET INSTALLATION (OPTIONAL) The headsets is used to make or receive a call. With the headset, you can have the convenience of hands free communication while using your cordless phone. 1) Place the headset on your head so the speaker covers your ear. The other end of the headset should rest comfortably against the side of your head above your ear. Do not place the end of the headband against the other ear.
UP354BH(WDECT2355+2) OM 5/14/04 10:49 AM Page 10 ABOUT THE MENU OPTIONS There are 6 main menu options, (DirectLink Mode, Room Monitor, Handset Setup, Answ. Setup, Global Setup and System Reset) and submenu options. During Global Setup and System Reset, make sure your cordless phone is in standby mode (not in use), and all handsets are within range of the main base unit.
UP354BH(WDECT2355+2) OM 5/14/04 10:49 AM Page 11 Handset Setup The following submenu options must be set separately for each handset. Submenu name Ringer Tones (Default is Flicker) Distinct. Ring (Default is on) AutoTalk (Default is on) Anykey Answer (Default is on) Banner (True Banner) Key Touch Tone (Default is on) Description Adjusting the ringer tone (tone your phone makes when ringing) (see page 16). Set the distinctive ring (see page 16).
UP354BH(WDECT2355+2) OM 5/14/04 10:49 AM Page 12 Answering Setup This main menu option allows you to set up TAD settings from your handset. You can also set these submenu options from the base (see page 45). Submenu name Security Code (Default is 80) Ring Time (Default is 9 time) Record Time (Default is 1 minute) Message Alert (Default is off) Call Screen (Default is on) [ 12 ] Description Select a two-digit Personal Identification Number (PIN) code.
UP354BH(WDECT2355+2) OM 5/14/04 10:49 AM Page 13 Global Setup If you change one of the Global settings, you change the setting for all additional handsets. Only one handset can change Global settings at a time. Submenu name Day & time Name Tag (POP ID) (Default is on) Insert 0 Dial Mode (Australia only) (Default is tone) Copy Phonebook Description Set the day and time of your display (see page 19).
UP354BH(WDECT2355+2) OM 5/14/04 10:49 AM Page 14 SETTING UP THE MENU Entering the Menu To back to the previous screen, press /del. 1) Press the /del key in standby mode. DirectLink Mo de 2) Use /vol/ or /vol/ to move the pointer to a desired main menu (DirectLink Mode, Room Monitor, Room Monit or Handset Setup, Answ. Setup, Global Setup, and Handset Se tup System Reset). 3) Press to select the desired main menu. 4) Use /vol/ or /vol/ to select a desired submenu, and then press to enter.
UP354BH(WDECT2355+2) OM 5/14/04 10:49 AM Page 15 Room Monitor Using Room Monitor 1) Enter the Room Monitor menu (see “Entering the Menu” on page 14). To Room Monitor appears. 2) Select the handset you want to monitor by using /vol/ or /vol/ . 3) Press . RoomMonitor appears, and you hear sounds in the room where the handset is installed. 4) To finish the Room Monitor, press or return the handset to the cradle. To Room Monitor Handset #2 Base This is an example, if you have handset #1 and #2.
UP354BH(WDECT2355+2) OM 5/14/04 10:49 AM Page 16 Handset Setup Selecting a Ringer Tone 1) Enter the Handset Setup menu, and then the Ringer Tones submenu (see “Entering the Menu” on page 14). Ringer Tone s Flicker Clatter There are 10 ringer tones or 10 polyphonic tones to choose from.
UP354BH(WDECT2355+2) OM 5/14/04 10:49 AM Page 17 Setting the Anykey Answer 1) Enter the Handset Setup menu, and then the Anykey Answer submenu (see “Entering the Menu” on page 14). 2) Press /vol/ or /vol/ to select On or Off. 3) Press . You will hear a confirmation tone. Anykey Answer On Off Setting the True Banner 1) Enter the Handset Setup menu, and then the Banner submenu (see “Entering the Menu” on page 14). 2) Use the number keypad (0-9), , , or /del to enter or edit the name. 3) Press .
UP354BH(WDECT2355+2) OM 5/14/04 10:49 AM Page 18 Setting the Ring Time 1) Enter the Answ. Setup menu, and then the Ring Time submenu (see “Entering the Menu” on page 14). 2) Press /vol/ or /vol/ to select a Ring Time (Toll Saver, 4 Times, 6 Times, or 9 Times). 3) Press . You will hear a confirmation tone. Ring Tim e Toll Saver 4 Times Setting the Record Time 1) Enter the Answ. Setup menu, and then the Record Time submenu (see “Entering the Menu” on page 14).
UP354BH(WDECT2355+2) OM 5/14/04 10:50 AM Page 19 Global Setup Setting Name Tag (POP ID) 1) Enter the Global Setup menu, and then the Name Tag submenu (see “Entering the Menu” on page 14). 2) Press /vol/ or /vol/ to change the selection, On or Off. 3) Press . You will hear a confirmation tone. Setting Insert Zero (New Zealand only) 1) Enter the Global Setup menu, and then the Insert 0 submenu (see “Entering the Menu” on page 14). 2) Press /vol/ or /vol/ to change the selection, On or Off. 3) Press .
UP354BH(WDECT2355+2) OM 5/14/04 10:50 AM Page 20 Setting the Dial Mode (Australia only) 1) Enter the Global Setup menu, and then the Dial Mode submenu (see “Entering the Menu” on page 14). 2) Press /vol/ or /vol/ to change the select, Tone or Pulse (the initial setting is Tone). 3) Press . You will hear a confirmation tone. Dial Mode Tone Pulse Copy Phonebook • If you receive a call or set up the Global Setup menu, the transfer will be canceled.
UP354BH(WDECT2355+2) OM 5/14/04 10:50 AM Page 21 System Reset De-register the Handset 1) Enter the System Reset menu, and then the Deregister HS submenu (see “Entering the Menu” on page 14). 2) Press /vol/ or /vol/ to select the handset ID to be de-registered from the list, and then press . Deregister HS? appears. 3) Press /vol/ or /vol/ to select Yes. 4) Press . You will hear a confirmation tone. When de-registration is complete, Deregistration Complete appears.
UP354BH(WDECT2355+2) OM 5/14/04 10:50 AM Page 22 MAKING AND RECEIVING CALLS BASICS • To set Autotalk, see page 16 or to set Anykey Answer see page 17. • The handset microphone is located at the bottom of the handset (see “Controls and Functions” on page 1). Position yourself as near to the handset as possible and speak clearly. • If the line is in use by another handset(s), Line In Use appears in the display of all registered handset’s display, that are not in use.
UP354BH(WDECT2355+2) OM 5/14/04 10:50 AM Page 23 KEYPAD LOCK The Keypad Lock prevent user from pressing the keypad accidentally. You can still answer calls, and receive page and phonebook locations, and the keypad lock is reactivated after the operation. To lock the keypad Press and hold Keypad Locked appears. until you hear a confirmation tone. If anykey is pressed when keypad is locked, To unlock keypad press & hold * key appears. To unlock the keypad Press and hold again.
UP354BH(WDECT2355+2) OM 5/14/04 10:50 AM Page 24 REDIALING A CALL The last three phone numbers dialed can be quickly redialed. • If the number exceeds 32 digits, only the first 32 digits are retained in redial memory. • If the redial memory is empty, you will hear a beep. Redialing from Standby Mode < R edi a l1> 8 007 3 034 5 6 1) Press redial/pause in standby mode. 2) Press redial/pause again. Each press of redial/pause will display one of the last three number redialed. 3) Press or speaker.
UP354BH(WDECT2355+2) OM 5/14/04 10:50 AM Page 25 Redialing from the Base 1) Press on the base. 2) Press redial/p on the base. The last number dialed from the base is redialed. ADJUSTING THE HANDSET RINGER, EARPIECE AND SPEAKER VOLUME Handset ringer volume Press the volume up key or volume down key (labeled as /vol/ or /vol/ in standby mode to select one of three ringer volume (off, low, or high). Earpiece and speaker volume Standby Mode - The handset is not in use and has not been pressed.
UP354BH(WDECT2355+2) OM 5/14/04 10:50 AM Page 26 DO NOT DISTURB (DND) • Standby Mode - The handset is not in use and has not been pressed. • Setting the DND to on while the answering system is off turns the answering system on automatically. The answering system returns to the original setting when you cancel the DND. • If you press ans on/ off when the DND and the answering system is on, both of the DND and the answering system will turn off.
UP354BH(WDECT2355+2) OM 5/14/04 10:50 AM Page 27 TONE DIALING SWITCH-OVER (AUSTRALIA ONLY) Some telephone companies use equipment that requires pulse dialing (sometimes referred to as rotary dialing). If you need to enter tone dialing digits, you can switch-over to tone dialing during the call. This feature is useful when you need tone dialing to use automated systems, for example, entering your bank account number after you have called your bank. Initially make your call with the pulse dialing mode.
UP354BH(WDECT2355+2) OM • Normally, the talk time duration is 7 hours, however, when the Clarity Booster is On, the talk time duration will be up to 5 hours with fully charged batteries. • Clarity booster automatically turns off after each call. 5/14/04 10:51 AM Page 28 1) Press /del during talk time (while phone is in use). 2) Press /vol/ or /vol/ to move the pointer Talk B to Clarity Boost, and then . Boost On and B appear in the display.
UP354BH(WDECT2355+2) OM 5/14/04 10:51 AM Page 29 When speaking on the base 1) Press or speaker on the handset to initiate the 3-way conversation. 2) To hang up, return the handset to the cradle, or press key on the handset. The base will still be connected to the call. FIND HANDSET To locate the handset, press mute/find handset on the base when the base is in standby mode. All registered handsets beeps for 60 seconds, and Paging appears on the handset display.
UP354BH(WDECT2355+2) OM 5/14/04 10:51 AM Page 30 PHONEBOOK PHONEBOOK • Your phone has 100 memory locations for Caller ID messages or stored Phonebook numbers. • Selecting a speed dial location where a number is already stored releases the old number’s speed dial setting. The new number will be stored in the speed dial location. • When the memory is full, you will hear a beep and Memory Full appears. You cannot store names and numbers. • The pause key counts as one digit.
UP354BH(WDECT2355+2) OM 5/14/04 10:51 AM Page 31 6) Distinctive Ring appears. Press /vol/ or /vol/ to move the pointer to one of the Distinctive Ring options, and then press . Distinctive Ring No Selectn Flicker If you choose not to store a Distinctive Ring, simply select the “No Selectn” option. 7) Speed Dial appears. Press /vol/ or /vol/ to move the pointer to select the Speed dial location (10 locations: SPD1-SPD0).
UP354BH(WDECT2355+2) OM 5/14/04 10:51 AM Page 32 STEPS FOR ENTERING NAMES AND SPECIAL CHARACTERS Refer to the letters on the number keys to select the desired characters. With each press of a number key ( ), the displayed character appears in the following order: upper case letters first, lower case letters next and finally the number corresponding to the key.
UP354BH(WDECT2355+2) OM 5/14/04 10:51 AM Page 33 If you make a mistake while entering a name Use or to move the cursor to the incorrect character. Press /del to erase the wrong character and then enter the correct character. To delete all characters, press and hold /del. For example, to enter Movies: 1) When the phone is in standby mode, press 2) Press phonebook. , Store/Edit Name appears. 3) Press 6 once, and then press to move the cursor to the right. 4) Press 6 six times. 5) Press 8 six times.
UP354BH(WDECT2355+2) OM 5/14/04 10:51 AM Page 34 VIEWING THE PHONEBOOK Your phone stores names/numbers in the phonebook memory locations, and you can search names in alphabetical order. You can view the phonebook even while the phone is in use. 1) Press phonebook. Phonebook :10 0 Search [A-Z / / ] Store [SEL ECT ] If you recall the phonebook during a call, Store [SELECT] will not appear. 2) Press /vol/ , /vol/ , or the number keypad to scroll through the phonebook locations.
UP354BH(WDECT2355+2) OM 5/14/04 10:51 AM Page 35 MAKING CALLS USING THE PHONEBOOK From Standby Mode 1) When the phone is in standby mode, view the phonebook location to dial (see “Viewing the Phonebook” on page 34). 2) Press is dialed. or 3) To hang up press speaker. The displayed number Movies 0295979035 Beethoven9/SPD1 . From Talk Mode 1) Press or speaker. 2) View the phonebook location to dial (see “Viewing the Phonebook” on page 34). 3) Press .
UP354BH(WDECT2355+2) OM 5/14/04 10:51 AM Page 36 EDITING OR ERASING A STORED NAME, PHONE NUMBER, DISTINCTIVE RING, AND SPEED DIAL 1) When the phone is in standby mode, press phonebook. 2) Press /vol/ or /vol/ , or the number keypad to view the phonebook locations (see “Viewing the Phonebook” on page 34). Phonebook :10 0 Search [A-Z / / ] Store [SEL ECT ] a. Editing the Stored Data 1) When the phonebook location to be edited appears, press . Store/Edit Name appears.
UP354BH(WDECT2355+2) OM 5/14/04 10:51 AM Page 37 CHAIN DIALING The memory locations in the handset are not limited to phone numbers. You can also store a group of numbers (up to 20 digits), that you need to enter once your call connects. This is referred to as Chain Dialing. An example of this is a bank account number. Store the account or special number in one of the phonebook locations. (Refer to “Storing Phone Numbers, Names, Distinctive Rings and Speed Dial” on page 30.
UP354BH(WDECT2355+2) OM 5/14/04 10:51 AM Page 38 CALLER ID CALLER ID • If you answer a call before the Caller ID message is received (for example, before the second ring), the Caller ID message will not appear. • When the call is received via a telephone company that does not offer Caller ID service, the caller’s phone number and name does not appear. (This includes some international calls.) • When the call is via a private branch exchange (PBX), the caller’s phone number and name may not appear.
UP354BH(WDECT2355+2) OM 5/14/04 10:51 AM Page 39 2) When you pick up the phone, the display changes to Talk. (AutoTalk feature is set to on). Data errors appear as “ .” VIEWING THE CALLER ID LIST The Caller ID list stores information for incoming calls - even unanswered calls. You can store 100 of the Caller ID messages and Phonebook locations (including SpeedDials) in total. You can view the Caller ID list during a call or when the phone is in standby mode. 1) Press . The summary screen appears.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 40 DELETING A CALLER ID MESSAGE Deleting Information from the Caller ID List • Once the Caller ID data has been deleted, the information cannot be retrieved. • Standby Mode The handset is not in use and has not been pressed. • Talk Mode The handset is not in the cradle and or speaker has been pressed enabling a dial tone. Talk appears on the display.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 41 USING THE CALLER ID MESSAGE LIST Calling a party from the Caller ID list From Standby mode 1) When the phone is in standby mode, view the Caller ID message (see “Viewing the Caller ID List” on page 39). 2) Press or speaker. The displayed phone number dials automatically. 21/12 11:20AM Jane Smith 0295979035 From Talk mode 1) Press or speaker. 2) View the Caller ID message you want to dial (see “Viewing the Caller ID List” on page 39). 3) Press .
UP354BH(WDECT2355+2) OM THE INTEGRATED ANSWERING DEVICE [ 42 ] 5/14/04 10:52 AM Page 42 THE INTEGRATED ANSWERING DEVICE The phone has a built-in answering system that answers and records incoming calls. You can also use your answering system to record a conversation, leave a voice memo message or to announce a special outgoing message to callers when you’re away from your phone.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 43 Answering System Default Settings Some answering system functions can be set through the base or handset. Default settings for each function are as follows: Functions Answer On/Off Time Security Code Ring Time Record Time Message Alert Call Screen Default Setting On SUN 12:00 AM* 80 9 times 1 minute Off On Reference Page Base Handset P. 43 P. 46 P. 19 P. 46 P. 17 P. 47 P. 18 P. 47 P. 18 P. 48 P. 18 P. 49 P.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 44 SETTING UP YOUR ANSWERING SYSTEM Setting your outgoing message (Greeting) • When the answering system is full, FL appears on the base. You should delete some messages so that the system can record new messages. • Position yourself as near to the base as possible and speak clearly when recording your outgoing message. • If you make an outside call, or a call is received on the base during the operation, the operation is canceled.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 45 1) When the phone is in standby mode, press /vol/ or /vol/ repeatedly to scroll through ringer volumes. The ringer level is displayed, and you will hear each volume level. The last ringer heard will be the volume setting, then the phone returns to standby mode. 2) You can also set the base ringer volume while the phone is ringing by pressing the /vol/ or /vol/ .
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 46 Setting the Time Time stamp will not be heard until you have set the time. Follow these steps to set the clock on the answering system to the correct time. 1) Press clock/MENU. 2) Press skip/SELECT or repeat/SELECT until the correct day is announced and the corresponding number (from 1 Sunday to 7 Saturday) appears. 3) Press SET to select the day. 4) Press skip/SELECT or repeat/SELECT until you hear the correct hour setting.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 47 Setting the ring time The ring time setting allows you to set the number of rings the caller hears before your answering system plays the outgoing message. You can set the ring time to answer after four, six, nine rings. If you enable the Toll Saver (TS setting), the answering system picks up after six rings if you have new messages, and after nine rings if there are none.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 48 Announce only feature The Announce only feature plays a pre-recorded outgoing message or your own personal outgoing message, but it will not allow the caller to leave a message. To set “Announce only”, follow the steps on page 47. To choose between the pre-recorded message or your own personal greeting, press greeting, when the outgoing message is played. Press greeting to select the greeting of your choice.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 49 Setting the call screen You can screen calls when the Call Screen function is set to On. 1) Press clock/MENU six times. The current Call Screen setting (On or Off) appears on the base. 2) Press skip/SELECT or repeat/SELECT to choose On or OF. 3) Press SET. A confirmation tone sounds, and the system announces the new setting. Screening a call • If you set the call screen to off, you can not screen a call.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 50 USING YOUR ANSWERING SYSTEM The message counter displays the number of messages stored in memory. If the display flashes, then there are new messages waiting for you. The answering system plays your new messages first. After you play all your new messages, you can then play your old messages. Playing your messages • The time stamp will not be heard until you have set the time. 1) When the phone is in standby mode, press play/stop.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 51 Skipping a message 1) Press play/stop to review your messages. The number of stored messages is announced. 2) Press skip/SELECT at anytime to skip to the next message. Each time skip/SELECT is pressed, the system scans forward one message. If you have several messages, press skip/SELECT repeatedly to find the message you want to play. To quickly scroll through a message, press and hold skip/SELECT. The system advances through the playback at double speed.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 52 Voice memo • The voice memo messages are recorded as an incoming messages. • When the answering system is full, FL appears on the display and recording is terminated. • If an outside call is received during the operation, the operation is canceled. • Every state has different regulations governing the recording of conversations over the telephone.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 53 REMOTE OPERATION You can check, play, or delete messages, even record a new greeting message from a remote location (when you are away from home, or from another room using a handset). Additionally, you can turn On or Off your answering system remotely. Remote access away from home You can operate your answering system from a remote location using any touch-tone telephone. 1) Call your telephone number and wait for the system to answer.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 54 * To repeat a message, press # then 1 within about four seconds to repeat the previous message, or press # then 1 after about four seconds to repeat the current message. ** For the Memo Record and Greeting Message Record functions, the first time you enter the corresponding command, it starts the Recording function. If you want to stop the recording, enter the command again.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 55 Remote Key Function /1 /2 /3 /4 /5 Repeat a Message* Playing incoming Messages Skipping a Message Deleting a Message Stop Operation 6 7 8 9 0 Answering System On Memo Record/Stop** Greeting Message Record/Stop** Answer System Off Help Guidance * For Repeat a Message function, press 1 within about four seconds to repeat the previous message, or press 1 after about four seconds to repeat the current message.
UP354BH(WDECT2355+2) OM 5/14/04 10:52 AM Page 56 EXPANDING YOUR PHONE 4 Multi-Handset Expendability EXPANDING YOUR PHONE • To use the WDECT2305, register it to the original base. • Save this manual for detailed operation. • All of the handsets ring when a call is received. [ 56 ] Your phone supports up to 4 handsets (including the handset(s) supplied with your phone). You can now place a fully-featured cordless handset anywhere AC power is available to connect the handset charger.
UP354BH(WDECT2355+2) OM 5/14/04 10:53 AM Page 57 REGISTER THE HANDSET If you purchase an extra handset, you need to register the handset to the base before use. Only one handset can be registered at a time. The handset ID for the supplied handset(s) was assigned at the factory, which has #1 or #2 in the display (#2 for models that have two handsets in packaging). When you register additional handset to the base, the handset ID will be assigned.
UP354BH(WDECT2355+2) OM 5/14/04 10:53 AM Page 58 USING TWO WAY COMMUNICATION BETWEEN THE HANDSETS ANYWHERE WITHOUT THE BASE (DIRECTLINK) Two handsets can be in DirectLink mode while other handsets are in use. To use this feature, you must enter the two handsets into the DirectLink mode first. To enter the DirectLink mode e See page 14 DirectLink Call 1) When the phone is in the DirectLink standby mode, press (example of DirectLink from handset #1).
UP354BH(WDECT2355+2) OM 5/14/04 10:53 AM Page 59 4-WAY CONFERENCING Fourth person, at either the handset or the base, may be added to the conference call. For example, to add a fourth party to an ongoing conference call at the base or another handset, press on the fourth party’s handset (or on the base). To remove either caller from your conversation, press on the party’s handset (or on the base). The other parties will still be connected to the call.
UP354BH(WDECT2355+2) OM 5/14/04 10:53 AM Page 60 Call Transfer Feature From handset to handset or to the base 1) During a call, press /transfer/int’com on the handset. 2) Select a handset or the base to transfer the call within 10 seconds. (Refer to step 2 in the intercom section on Hold,to tra nsf er page 59). Handset #2 The call will automatically be placed on hold, and an Base intercom tone sounds. To cancel the transfer, press or on the initiating handset.
UP354BH(WDECT2355+2) OM 5/14/04 10:53 AM Page 61 CHANGING THE DIGITAL SECURITY CODE 1. Perform the “System Reset” menu options (“De-register the Handset” and “Replacing the Base Setting”) for all the handsets you have (see page 21). 2. To register all the handsets do the following steps: 1) Place a handset, one at a time in the base. 2) Registration starts automatically. While registering Handset Registering appears in the display.
UP354BH(WDECT2355+2) OM 5/14/04 10:53 AM Page 62 TROUBLESHOOTING If your phone is not performing to your expectations, please try these simple steps first. Symptom The charge LED won’t illuminate when the handset is placed in the cradle. The audio sounds weak and/or scratchy. Can’t make or receive calls. The handset doesn’t ring or receive a page. “Unavailable” appears in the display. [ 62 ] Suggestion • Make sure the AC adapter is plugged into the base and wall outlet.
UP354BH(WDECT2355+2) OM 5/14/04 Symptom 10:53 AM Page 63 Suggestion Severe noise interference. • Keep the handset away from microwave ovens, computers, remote control toys, wireless microphones, alarm systems, intercoms, room monitors, fluorescent lights, and electrical appliances. • Move to another location or turn off the source of interference. The Caller ID does not display. • The handset was picked up before the second ring. • The call was placed through a switchboard.
UP354BH(WDECT2355+2) OM 5/14/04 Symptom Messages are incomplete. 10:53 AM Page 64 Suggestion • The incoming messages may be too long. Remind callers to leave a brief message. • The memory may be full. Delete some or all of the saved messages. No sound on the base unit • Adjust the speaker volume on the base unit. speaker during call monitoring or • Make sure the call screen feature is set to on. or message playback. Cannot access remote call-in • Make sure you are using the correct PIN number.
UP354BH(WDECT2355+2) OM 5/14/04 10:53 AM Page 65 INDEX 0-9 3-way conferencing ....................28 4-way conferencing ....................59 20 ring options ..........................16 A Announce only feature ................48 Answering system Deleting a message ..................51 Playing your messages ..............50 Recording a conversation ..........52 Remote access ..........................53 Repeating a message ................50 Skipping a message ..................51 Turning On/Off ......
UP354BH(WDECT2355+2) OM 5/14/04 10:53 AM Page 66 WARRANTY One Year Limited Warranty Important: Evidence of original purchase is required for warranty service. Warrantor: Uniden Australia Pty Limited A.B.N.
UP354BH(WDECT2355+2) OM 5/14/04 10:53 AM Page 67 REMOTE OPERATION CARD CUT REMOTE OPERATION CARD Remote access away from home Turn on the answering system remotely 1. Call your phone number from a touch-tone phone. 2. During the outgoing message, press # and enter your PIN code. The answering system announces the number of messages stored in memory and the help guidance. 3. To quit, hang up the phone. 1. Call your phone and let it ring 15 times until you hear a beep. 2.
UP354BH(WDECT2355+2) OM 5/14/04 10:53 AM Page 68 CUT Task Repeat a Message Playing incoming Messages Skipping a Message Deleting a Message Stop Operation Answering System On Memo Record/Stop Greeting Message Record/Stop Answer System Off Help Guidance [ 68 ] Key
UP354BH(WDECT2355+2) OM 5/14/04 10:53 AM Page 69 MEMO [ 69 ]
UP354BH(WDECT2355+2) OM 5/14/04 10:53 AM Page 70 Additional Handset & Charger Expand Your System! WDECT2305 HANDSET & CHARGER Easily expand your cordless phone system by adding the WDECT2305 Handset and Charger*. The WDECT2305 gives you the mobility you need to stay connected with friends and family.