Assembly Instruction

2of3
STEP 5 - Install Bulbs
A. Insert bulbs onto the sockets and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
Figure 5
Nipple
BB
DD
CC
Supply Wires
and Ground
Wire
Figure 3
Canopy
Chain Loop
Canopy
Lock Ring
CC
Fixture
Loop
Socket
T8 Vintage Bulb
(recommended
but not supplied)
STEP 2 - Install the Crossbar Assembly to Outlet Box and Adjust
the length of the Nipple
A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head
of the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included), tighten until snug
B. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
C. Remove the canopy lock ring from the canopy chain loop. Place the
Ceiling Canopy (DD) over the canopy chain loop against the ceiling
to determine the correct position of the nipple. Thread the canopy
lock ring onto the canopy chain loop. Adjust the nipple to allow the
Ceiling Canopy (DD) to rest against the ceiling when held in place by
the canopy lock ring.
D. Remove the canopy lock ring and the Ceiling Canopy (DD). Tighten
the lock washer and the hex nut against the crossbar to secure in
place.
.
STEP 3 - Install the Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (BB) to your desired length by removing
links if needed. Put a cloth over the Fixture Chain (BB) to protect the
finish.
B. Pull the supply wires through the Fixture Chain (BB) alternating
links. After the wires are through the Fixture Chain (BB), pull the
Supply Wires and the Ground Wire through the canopy lock ring and
the Ceiling Canopy (DD) in order.
C. Attach one end of the Fixture Chain (BB) to the fixture loop with one
Figure 4
STEP 4 - Making the Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
B.
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire from fixture
identified with the Label “N”
Black wire from
outlet box (or Red)
Black wire from fixture
identified with the label “L”
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Outlet Box Screw
(not included)
Hex Nut and
Lock Washer
Outlet Box
Green Ground Screw
AA
Canopy Chain Loop
Canopy Lock Ring
Figure 2
Nipple
DD
Quick Link (CC). Lift the fixture
and Fixture Chain (BB) up and
attach the other end of the Fixture
Chain (BB) onto the canopy chain
loop with another Quick Link (CC).
The fixture will now hang safely.
D. Feed the Supply Wires and
Ground Wire through the canopy
chain loop and nipple into the
outlet box. Cut the wires leaving
approximately 8” of wire
extending from the Outlet Box.
E. Go to Step 4 for wire connections
and follow the directions. Return
to Step F in this step when
complete with Step 4.
F. Raise the Ceiling Canopy (DD)
and canopy lock ring up the
Fixture Chain (BB) and over the
canopy chain loop. Tighten the
canopy lock ring onto the canopy
chain loop until tight.
Suggested chain length for
Ceiling height :
9’ ceiling : use 2 links of chain and
2 quick links
10’ ceiling : use 12 links of chain
and 2 quick links