SILVER 50 SPIRAL MIXER OPERATOR’S MANUAL Persons under age 18 are not permitted to operate or have accessibility to operate this equipment per U.S. Dept. Of Labor Employment Standards Administration Fact Sheet No. ESA913.
Welcome to Univex Thank you for purchasing this Univex Product. Your new SILVER 50 spiral mixer has been designed with advanced performance and safety features that make it an excellent addition to your food preparation equipment. Like all Univex mixers, slicers, meat grinders and accessories, this mixer is engineered to provide years of reliable service.
TABLE OF CONTENTS DESCRIPTION PAGE TABLE OFCONTENTS . . . . . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 LIST OF ILLUSTRATIONS . . . . .. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 OVERALL VIEW OF THE MACHINE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 CHOOSING THE RIGHT LOCATION FOR YOUR MIXER . . . . . . . . . . . . . . . . . . . . 5 USER FRIENDLY SAFETY GUARD . . . . . . . . . .. . . . . . . . .
OVERALL VIEW OF SPIRAL MIXER FIGURE 1 1. CONTROL PANEL 2. STAINLESS STEEL GRID 3. USER FRIENDLY SAFETY GUARD 4. BOWL 5. LOWER FRONTAL COVER 6. ADJUSTABLE FOOT 7. WHEELS 8. MAIN POWER CABLE 9. FIXED MIXTURE GUARD 10.
CHOOSING THE RIGHT LOCATION FOR YOUR NEW MIXER When selecting the best location for the mixer, it is helpful to consider the following: • Where is the best location for the operator, both for saving steps and easy viewing? • Is this a good location for product flow as in: • Easy to get ingredients to the mixer? • Destination of the mix after mixing? • Is there existing electrical service at this location? • Does this location provide easy access for cleaning and service? • Check to be sure that your mixer w
OPERATING THE SILVER 50 SPIRAL MIXER Your Univex SL50 mixer is designed to meet the pizza and baker’s demand for an efficient, dependable appliance. It should give unfailing performance over a period of years when operated and maintained according to the instructions contained herein. The speeds of the spiral approximately 90 to 95 revolutions per minute (RPM) in 1st speed and approximately 180 to 190 RPM for the 2nd one. The speed of the bowl approximately 13/15 RPM on any speed of spiral.
Set the times for 1st and 2nd speed. The lights on the timer will switch on to show the minutes set. After pressing “start” the mixer will countdown the 1st timer then start the 2nd timer until the end of cycle. ATTENTION: The safety cage must be down for the mixer to work. Otherwise the mixer will not run. Check the correct rotation direction of the bowl (clockwise, according to the arrow). If incorrect, contact a qualified electrician.
CLEANING YOUR MIXER Consistent use of the following procedures will ensure that your mixer is in optimum operating condition. • Warning: disconnect the electrical power supply before cleaning. • Wash the body of the mixer, safety guard, the bowl, spiral, countershaft with warm water and mild soap. • Avoid excess water in the area of the frontal control panel • Do not rinse the mixer with a hose. • Do not use abrasive pads to wash the mixer. • Dry the mixer thoroughly with a soft cloth.
TROUBLE-SHOOTING GUIDE TROUBLE 1. MIXER WILL NOT OPERATE 2. MIXER RUNS BUT SPIRAL WILL NOT TURN. 3. SPIRAL RUNS BUT BOWL WILL NOT RUN POSSIBLE CAUSE REMEDY 1.1 ELECTRICAL SERVICE DOWN. 1.1 CHECK ELECTRICAL SERVICE. REPLACE FUSEOR RESET CIRCUIT BREAKER AS NECESSARY 1.2 BURNED SWITCH CONTACTS. 1.2 REPLACE OR CLEAN CONTACTS.* 1.3 TIMER NOT TURNED ON 1.3 TURN TIMER ON 1.4 BURNED OUT MOTOR 1.4 REMOVE, TEST, REPAIR OR REPLACE* 1.5 SAFETY GUARD NOT CLOSED 1.5 CLOSE SAFETY GUARD 1.
Dimensions Figure 3 PAGE 10
WIRING DIAGRAM 208-240 V, 60HZ, 3PH figure 4a WARNING: Whenever maintenance is being performed, or whenever the top cover or rear access panel have been removed , DISCONNECT THE ELECTRICAL POWER SUPPLY and place a tag on it indicating that the mixer is being worked on.
WIRING DIAGRAM 208-240 V, 60HZ, 3PH figure 4b WARNING: Whenever maintenance is being performed, or whenever the top cover or rear access panel have been removed , DISCONNECT THE ELECTRICAL POWER SUPPLY and place a tag on it indicating that the mixer is being worked on.
WIRING DIAGRAM 208-240 V, 60HZ, 3PH figure 4c WARNING: Whenever maintenance is being performed, or whenever the top cover or rear access panel have been removed , DISCONNECT THE ELECTRICAL POWER SUPPLY and place a tag on it indicating that the mixer is being worked on.
PAGE 13 WIRING DIAGRAM 208-240 V, 60HZ, 3PH figure 4d WARNING: Whenever maintenance is being performed, or whenever the top cover or rear access panel have been removed , DISCONNECT THE ELECTRICAL POWER SUPPLY and place a tag on it indicating that the mixer is being worked on.
PAGE 14 WIRING DIAGRAM 208-240 V, 60HZ, 3PH figure 4 e WARNING: Whenever maintenance is being performed, or whenever the top cover or rear access panel have been removed , DISCONNECT THE ELECTRICAL POWER SUPPLY and place a tag on it indicating that the mixer is being worked on.
Warranty The Univex SL50 spiral mixer carries a One-Year, on-site, parts and labor warranty against any defects in materials or workmanship. The one-year period begins on the date of purchase by the end user and remains in full effect provided the unit is used properly and in accordance with our operators manual. Any work to be performed under this warranty must be performed between the hours of 8:00 a.m. and 5:00 p.m. local time, Monday through Friday. Univex will not cover overtime charges of any kind.
