Operation Manual

29
THE FUNCTIONS OF THE BREADMAKER
Alarm function
The alarm sounds:
 whenever an active button is pressed,
 during the second kneading process, to remind you to add
seeds, fruit, nuts or other ingredients. Please note that this
function cannot be deactivated, e.g. in the time preset
function,
 at the end of the baking process, the appliance beeps often
during the keep-warm phase,
 at the end of the keep-warm phase 10 beeps remind you
that the appliance is now switched off and the bread has to
be taken out of the bread pan. Please note that this function
cannot be deactivated, e.g. in the time preset function.
Repeat function after power outage
Should the electricity supply been cut off during the operation
of the Breadmaker, the appliance will re-start, on re-instatement
of the supply, automatically from the point arrived at when the
cut-off occurred as long as the interruption is not longer than
2 minutes. If the interruption in the electricity supply lasts
more than 2 minutes and the display shows the basic setting,
the Breadmaker must be re-started. This is only practical if the
dough was not further than the kneading phase when the break
occurred. If the program was already in the last rising cycle when
the power broke down and the interruption lasts over a longer
time, the dough cannot be saved and the program has to be
started again.
Safety functions
The lid should not be opened after the program has started, except
during the second kneading phase for adding of ingredients.
During the rising and baking phase the lid should never be opened,
as the bread may sink down.
If the temperature in the appliance, due to previous use, is too
high (above 40 °C) for a newly chosen program, when an attempt
to re-start is made, the display will show H:HH and an alarm
sound will be heard. Should this occur, remove the pan and wait
until the appliance has cooled off and is back to the beginning of
the originally chosen program.
Please not that the breadmaker has no top heating for safety
reasons, so the crust will be lighter on top and darker at the sides
and bottom of the bread. For safety reasons an additional top
heating is not allowed.
If after pressing START/STOP, E:EE is shown in the display,
the temperature control is defective. In this case please send
the appliance to our technical service (address see Warranty
Conditions).
EIGENPROGRAMM/USER PROGRAM
In addition to the other numerous programs provided by the
BACKMEISTER
®
you can also program your own USER PROGRAM.
You can change the basic time and program phase settings as
programmed at the factory or leave out various program phases.
This allows you to develop your own individual program for baking
bread or preparing dough. Below you will find a sample recipe.
First you should become familiar with the following information
on the basic programming and use of the USER PROGRAM.
USER PROGRAM
The program features the following options
Browning programmable
Timer programmable
Loaf size I and II not programmable
The default program is the same as for the BASIC program.
Phase Preset Programmable time frame
Total time 3:10 hours
Knead 1 12 minutes 0-14 minutes
Rise 1 18 minutes 0-100 minutes
Knead 2 15 minutes 0-15 minutes
Rise 2 85 minutes 0-100 minutes
Rise 3 OFF/AUS 0-120 minutes
Bake 60 minutes 0-70 minutes
Keep warm 60 minutes OFF/60 minutes
The times can be programmed as shown in the table.
Proceed as follows:
Select the USER PROGRAM with the Menu button.
Select the desired phase with the ABSCHNITT button. Knead
1 and the programmed time 0:12 for this phase appear on the
display.
The time can be changed by means of the ZEITWAHL button.
Press it repeatedly until the desired time appears on the display
(past OFF, if necessary).
Confirm the change with the ABSCHNITT button. Press this
button again and the next program phase and the programmed
time will appear on the display: Rise 1 = and 0:18.
If the maximum programmable time for the respective program
phase is exceeded by pressing the ZEITWAHL button, O will
appear on the display if this is possible according to the above
table. This phase is then skipped during the program.
Every programmed setting must be confirmed by pressing the
ABSCHNITT button, so you can continue programming the next
program phase.
Once you have programmed all phases to suit your preferences,
conclude the programming by pressing the ABSCHNITT button
and then the START/STOP button. The programmed time for the
user program appears on the display. The program then starts
either immediately or after the time set via the timer function.