Quick Start Guide

Charging instruction
Please be aware the battery pack is directivety. When installing
battery, please start with top side. Inserting top side first, then
push battery top ward, let bottom side in to battery coaintaner.
Do not overexert or squze battery. Close the battery door, battery
door and rear cover should closed tight and flat.
How to install battery
1、After receiving the device (including batteries), we recommend
customer immediately start to use, if couldn’t, store period should
not exceed 3 months.
2、Please always charge battery in time after drain. Do not store
battery with drain or full condition. We suggest keep battery capacity
at around 50% when store.
3、Please use authorized charger to charge. Do not use 3rd party’s
cradle or adapter.
4、If not use the device for long period of time please keep the battery
and the device separately.
5、The battery stored in warehouse, must charge/discharge once every 3
months, keep 60% to 70% capacity (i.e. 3.8V to 3.9V).
6、Lithium-ion battery should be stored in a cool, dry, ventilated
environment, recommend to store between 0 to 28 degrees C.
7、Do not use metal to contact or short circuit between two electrodes.
Do not put device into overheating, excessive tide or decay environment.
Do not squeeze or collision.
Battery tips
1、It’s forbidden for transport when temperature is higher than
65 C.
2、The battery needs to be individual packed, do not directly stack
without protection. Avoid battery electrodes contact to short circuit.
3、Suggest isolate each battery by bags, paper, foam or other isolation
materials before pack in the carton.
4、Fill the room of carton by cushioning material before packing to avoid
shaking.
Transportation Notice
5. The battery is made from a flammable and explosive material.
Do not disassemble, squeeze, drop and make any other
destructive operations on the battery. Do not place the battery in
high temperatures.
6. Disposal of used batteries is subject to local relevant
documents or policies regarding disposal of used batteries.
Precautions
1. Read all information in this guide before using the device to
ensure safe and proper operation.
2. Please use the accessories that have been approved by Urovo
and corresponds to this model. Use of any power source, charger,
battery, etc. that has not be
en approved by Urovo may cause a
fire, explosion, or other hazards.
3. Please use device and accessories within the specified
temperature range. Equipment failure may occur when the
ambient temperature is too high or too low.
4. Do not disassemble the product and its accessories. If the
equipment or any of its components are not working properly,
Note: The contents of the manual are subject to change without prior notice
Warranty Policy
Warranty Terms:
1. Under normal circumstances, the warranty period of the device is
12 months (3 months for accessories), subject to the sales agreement.
2. During the product warranty period, under the normal use
conditions (determined by our technical staff), the user will be
entitled to a free warranty for damaged or faulty warranty parts.
3. During the warranty period, faults caused by repair, disassembly or
modification of the product by a personnel other than our company,
improper installation, improper use by the user (failure to follow
instructions), serial number damage, accident or natural disaster, will
not be covered under the warranty.
4. The warranty will expire immediately if any alterations are made
to the warranty card.
5. Please show the equipment SN and purchase certificate for
repair. The company reserves the right to interpret the above
contents.
Place of Origin:
Shenzhen
Quality Inspector:
02
UROVO TECHNOLOGY LTD.
Website: en.urovo.com
Thank you for using Urovo smart terminal series products. In the
situation of quality problems, which arise from raw materials or
production processes, during normal use of purchased products,
UROVO TECHNOLOGY LTD. will be responsible for free
maintenance within one year from the date of purchase.The
company may provide repairs due to the user's failure to use the
product according to the provided instructions of the product.
However, corresponding service fee and component fee will be
charged.
1、Use the USB cable to connect the device to a USB port on your
computer.
2、Open the notification panel and tap the USB connection icon.
After connected to PC, press
and drag down the top of the
screen will see USB setting
After switching to “file transfer” mode, PC side can conduct data
transfer and storage in “My computer”.
Remark: The device storage will be taken as a mobile disk by PC.
as a result, if installed another external storage card, two removable
disks will be seen on My PC.
click here to set USB mode
click here to set developer options
Touch to disable USB debugging.
USB debugging connected
Touch for more options.
USB for charging
Instructions for connecting computer
On
Debugging
USB debugging
Charging
File transfers
Photo transfer(PTP)
CANCEL
Bug report shortcut
Select mock location app
Enable view attribute inspection
Debug mode when USB is connected
Just charge this device
Transfer files to Window or Mac(MTP)
Transfer photos or files if MTP is not
supported(PTP)
Show a button in the power menu for
taking a bug report
No mock location app set
Select debug app
NO debug application set
Developer options
Use USB for
Check here switch to
Click here to enable
"USB debugging" mode
picture transfer mode
Check here to access
internal storage and TF card
Open the battery cover from here
Plug the charging cable into the micro Type-c port of the device .
The power indicator will turn red when charging. The red light goes
out when fully charged. If you charging /discharging frequently, we
recommend use charging cradle instead of Type-c cable.