R XML006-24K INSTRUCTION MANUAL For 42-80" TV If you have any questions along the way, just give us a call 1-800-460-0956 or mail to customerservice@x-mount.com.
Before getting started, let’s check below lists to make sure it is just right for you! 1 Check your TV VESA is within Min and Max size Does your TV MAX:600mm/23.62" (MIN:200mm/7.87") No? This mount is NOT compatible. MAX:400mm/15.74" (MIN:100mm/3.94") 2 No? Perfect – you may continue. (including accessories) Yes? This mount is NOT compatible. weigh MORE than 110 lbs.
-D TV INTERFACE 200mm [7.87in] 15mm [0.59in] 400mm [15.75in] 600mm [23.62in] WALL PLATE Ø9mm [Ø0.35in] SIDE VIEW - EXTENDED TOP VIEW - EXTENDED 609.6mm [24in] 177mm [6.97in] 282.7mm [11.13in] 15° 5° 372mm [14.65in] 245.2mm [9.65in] 406.4mm [16in] 649.3mm [25.56in] FULLY ASSEMBLED MOUNT SIDE VIEW - RETRACTED TOP VIEW - RETRACTED 683mm [26.89in] 62mm [2.44in] 429mm [16.
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service. Never use damaged parts! NOTE: Not all hardware included will be used. Parts and Hardware for STEP 1 TV Screws TV Brackets M4x12mm x4 Spacers M4x30mm M8x22mm 10mm x4 x4 x4 M6x12mm x4 M6x35mm 2.
Parts and Hardware for STEP 2 M8 Washer Lag Bolt Wall Plate Unit x4 x4 Mounting template R Concrete Wall Anchor 4pcs 16"(406.4mm) 8"(203.2mm) 24"(609.6mm) Contact us at telephone 1-800-460-0956 (USA) or mail to customerservice@x-mount.com. to have these additional pieces shipped directly to you.
1-1 Select TV Screws M4 M6 M8 6
1-2 Figure out the suitable position of brackets LOW MOUNTING HOLES INSTALL UP/DOWN IF NEEDED HIGH MOUNTING HOLES TV BRACKETS MUST BE LEVEL 7
1-3 Need Spacer? No, choose suitable screws and washers. Yes, choose suitable screws, washers and spacers. Tips: If you need to combine M6/M8(c/e/f) screws with 2.5mm spacers( i ), you have to remove the inner circle.
CAUTION: Avoid potential personal injury or property damage! ● Drywall covering the wall, must not exceed 5/8 in. (16 mm) ● Minimum wood stud size: common 2 x 4 in. (51 x 102 mm) nominal 1½ x 3½ in. (38 x 89 mm) ● Fits For 16 / 24 in Wood Stud. ● Stud center must be verified 1. Locate your studs. Verify and mark the center of the stud by finding the stud edges using a thin nail, or an edge to edge stud finder. 2.
3. Drill pilot holes using a 7/32 in. (5.5 mm) diameter drill bit. IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). Be sure to drill into the center of the studs. 4. Install wall plate using four lag bolts they are pulled firmly against the wall plate. and four washers . Tighten the lag bolts only until CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts. Go to STEP 4 on PAGE 14. 2.5"(64mm) 7/32" (5.
CAUTION: Avoid potential personal injury or property damage! ● Mount the wall plate assembly directly onto the concrete surface ● Minimum solid concrete thickness: 8 in. (203 mm) 1. Position the wall plate on the wall at your desired height. Level the wall plate and mark the hole locations. 2. Drill four pilot holes using a 3/8 in. (10 mm) diameter masonry drill bit. IMPORTANT: Pilot holes must be drilled to a depth of 2.5 in. (64 mm). 3/8" (10mm) 2.
3. Insert four anchors. CAUTION: Be sure the anchors are seated flush with the concrete surface. 4. Insert wall plate using four lag bolts pulled firmly against the wall plate. and washers .Tighten the lag bolts only until they are CAUTION: Improper use could reduce the holding power of the lag bolt. DO NOT over-tighten the lag bolts. No! Concrete Wall Anchor (Not included) Please contact us at telephone 1-800-460-0956 (USA) or mail to customerservice@x-mount.com.
Please make sure you install these extension arms in right direction.
Before hanging TV, please try to pull the mount to make sure that it has been assembled on the wall tightly.
Hang TV/bracket assembly onto wall plate them using bolts .
6-1 TV leveling adjustment (±4°): Loosen 4 leveling bolts on the rear of TV plate by maximum 2 turns, adjust to level, and retighten to secure.
6-2 Tilting angle adjustment (+5°/-15°): Loosen handle and tilting bolt, adjust TV to your desired position, then tighten handle and tilting bolt.
6-3 Cables manage: Manage TV cables orderly and guide them through the velcros.