Warranty

LIQUID VACUUM OPERATION

W A R N I N G : B E S U R E T O R E A D , U N D E R S T A N D , A N D A P P L Y , I N F O R M A T I O N E N T I T L E D

‘ S A F E T Y I N S T R U C T I O N S & W A R N I N G S ’ . D O N O T V A C U U M I N A R E A S W I T H F L A M M A B L E

G A S E S , V A P O R S , O R E X P L O S I V E D U S T S I N T H E A I R . F L A M M A B L E G A S E S O R V A P O R S

I N C L U D E B U T A R E N O T L I M I T E D T O : L I G H T E R F L U I D , S O L V E N T T Y P E C L E A N E R S , O I L -

B A S E D P A I N T S , G A S O L I N E , A L C O H O L , O R A E R O S O L S P R A Y S . E X P L O S I V E D U S T S

I N C L U D E B U T A R E N O T L I M I T E D T O : C O A L , M A G N E S I U M , G R A I N , O R G U N P O W D E R .

T O R E D U C E T H E R I S K O F H E A L T H H A Z A R D S F R O M V A P O R S O R D U S T , D O N O T

V A C U U M T O X I C M A T E R I A L S .

W A R N I N G : D O N O T P L U G P O W E R C O R D I N T O P O W E R O U T L E T . M A K E S U R E P L U G I S

D I S C O N N E C T E D B E F O R E C H A N G I N G T H E F I L T E R S .

L I Q U I D V A C U U M I N G

1. Verify that the power cord is disconnected from the outlet. (Fig. 1) Make sure that the

collection tank is clean and free from dust and dirt.

2. Remove cartridge lter, then carefully install the foam wet lter over the lter cage and place

the power head back on the collection tank. For lter installation instructions, see page 12.

D O N O T U S E T H E C A R T R I D G E F I L T E R F O R L I Q U I D V A C U U M I N G .

O P E R A T I N G I N S T R U C T I O N S : W E T V A C U U M I N G

3. Fit the desired nozzle to the vacuum hose. (Fig. 2)

4. Verify that the power switch is in the ‘O’ OFF position before plugging the power cord into the

outlet. (Fig. 3)

5. Turn the motor on by pressing the switch to the ‘I’ ON position. (Fig. 4)

6. Once you have completed vacuuming, ip the power switch to the 'O' (OFF) position and

unplug the power cord from the outlet.

7. After use, empty the collection tank by unscrewing the drain cap. Drain liquids into a suitable

receptacle or drain. (Fig. 5) Remember to ret the drain cap to the collection tank.

I M P O R T A N T ! When vacuuming large quantities of liquids, do not immerse the nozzle completely

in the liquid; leave a gap at the tip of the nozzle opening to allow air inow. The machine is tted

with a oat valve that stops the suction action when the collection tank reaches its maximum

capacity. You will notice an increase in motor speed. When this happens, turn off the machine,

disconnect from power supply, and drain the liquid into a suitable receptacle or drain. To continue

vacuuming, ret the collection tank with the drain cap. After wet vacuuming, turn the machine

off and remove plug from power supply. Empty the collection tank, clean and dry the inside and

outside b efore storage. R E M E M B E R ! The foam lter must be removed after wet vacuuming and

a cartridge lter must be installed before dry vacuuming again.

D O N O T U S E T H E C A R T R I D G E F I L T E R F O R L I Q U I D V A C U U M I N G .

1 3