COMMIE Exposed Roller Shower Door 5/16" glass (8mm) CAUTION: To reduce the risk of breakage, keep corner protectors on glass while installing. Keep corner protectors for use in case future adjustments are needed. Consult your local plumbing codes prior to installation. Recommended Clearance Heights for Installation: MODEL: 74 inches (188 cm) 02266074MB08N 02266074CHO8N Recommended Width for Installation: 02266058MBO8N 60-inch enclosure: 02266058CHO8N inches (142.2153.
Drill Bits 21/4” (3mm) dia. Screw Driver ®, Drill Level HSS Silicone Measuring Tape Soft Head Pencil Knife Sealant MASONRY DRILL) ( Safety Glasses | BIT FOR TILE ay @6mm | J Glove Carpenter's Squarer| | Masking or painter's Hack Saw tape ZTE Metal File CAUTION: When cutting or drilling metal components or when handling glass, to reduce the risk of personal injury, protective eye wear, gloves, and closed-toe shoes are required.
CAUTION Please carefully read the following important safety information before handling or installing this shower. There is a risk of serious injury while handling this product. To minimize these risks, please note: » Always wear safety glasses and gloves while handling. + Always follow the installation instructions. + Inspect glass for damage before installation.
PART# DESCRIPTION QTY Guide Block Alu.
A CAUTION: To avoid personal injury or property damage, identify components and read all instructions before installing. NOTE: Door height is (188 cm). Recommended Clearance Height for is 76" (193 cm.) This Com mix Exposed Roller Shower Door can be installed to open from either side of your enclosure depending on noncontroversial valve location. Bh The Glass Door should be installed on the same side as noncontroversial valve for optimal water retention.
Measure the finished opening width. IMPORTANT: Incorrect measurement may prevent proper door closure. Double-check measurement. Before beginning installation, verify the door assembly will fit within the horizontal opening of the shower enclosure. For the 60 3/8" door, the opening must be between 56" 60 3/8". » Wy Measure distance “W1” of upper shower enclosure opening and distance “W2” of lower shower enclosure opening.
Cut the Upper Guide Rail (K) to fit your finished opening using either a miter saw or a hacksaw Using a pencil or another marking tool , mark distance on the Upper Guide Rail (K) from the edge of the Upper Guide Rail (K) as shown in Fig.a. 9/16"] | CUT THIS END ONLY Fig.a A Cut the Upper Guide Rail (K) from the labeled end only! Cut the Upper Guide Rail (K) to: “W1” (top) dimension 1 9/16" Wear safety glasses and cut-resistant, non-slip gloves when drilling or cutting to avoid risk of injury.
Wall Jamb (N) Installation Sl Fig.a Fig.b g 1.Measure in 3/8" from the outside of the bathtub and make a mark and also check Wall Jamb(N) for plumb as Fig.a; 2.Position the outside edge of the Wall Jamb(N) on the of the bathtub.Mark the location of the holes as Fig.
Wall Jamb (N) Installation CAUTION: When cutting or drilling metal components or when handling glass, to reduce the risk of personal 7 injury, protective eye wear, gloves, and closed-toe shoes | are required. stud is presented behind the wall: drill a pilot hole into the stud and use the ST4.0 x 30mm Screws (bb) stud is presented behind the wall: drill a hole and insert the Wall Anchors (aa) and use the 8T4.0 x 30mm Screws (bb). 7 1.Remove Wall Jamb (N) and Drill the holes as Fig.a; 2.
Stationary Glass(O) Installation Carefully lay your glass panels flat on a soft, padded surface to inspect the glass. 1.Apply silicone into the groove along the entire full length of inside of back inner corner of the Wall Jamb (N) as Fig a; 2.Carefully, and with assistance from another capable person,insert the Stationary Glass(O) into Wall Jamb (N) as Fig b. Inside holes of the glass on the top! | © CAUTION: When cutting or drilling metal components Fig.
Roller(l)& Stopper(M) Installation 1. Install the Roller(l) on the Glass Door(E) and faces outside as Fig.a and Fig.b; 2. Install the Stopper(M) on Glass Door(E) as Fig.c . wrench Hold steady Si Ww CAUTION: When cutting or drilling metal components or when handling glass, to reduce the risk of personal injury, protective eye wear, gloves, and closed-toe shoes are required.
Insert Wall Bracket (J) to Upper Guide Rail (K) 1.With the supplied 2.5mm Allen wrench, loosen the four set screws on the top and bottom of bracket collar . 2 Remove the mounting bracket from the bracket collar. Carefully, and with assistance from another capable person, place Glass Door ( E ) into enclosure against rear wall,and the Roller faces outside.
8 Upper Guide Rail(K) & Glass Bracket (L)Installation Attach the Upper Guide Rail (K) to the inside of the Stationary Glass(O) with the Glass Bracket (L) as shown in Fig.a ; Use provided Allen wrench to hand tighten. IMPORTANT: Ensure all washers and bushings are installed as shown.
9 Wall Bracket (J) Installation 1.Ensure Upper Guide Rail(K) is level. Using a pencil or other marking tool, mark the projection of the Wall Bracket (J) location on the door wall Fig.a and Fig.b; 2.According to the note, drill two holes. Attach the mounting bracket using ST4 x 40 Screws (dd) as Fig.c. Fig.d and Fig.e; 3.Move bracket back a little bit;Align the Upper Guide Rail(K) with the bracket and Slide bracket outward (toward wall) over mounting bracket as Fig.f; 4.
Guide Block (A) can be installed on acrylic bathtub or stone bathtub. Please choose the installation method according to the bathtub type. Guide Block (A) installed on Acrylic bathtub 1.Remove the cap from the Guide Block(A). 2.Ensure the Stationary Glass(0) is plumb. Using a pencil or other marking tool, mark the hole as Fig.a 3.Drill one hole. Attach the Guide Block(A) using ST4 x 30 Screws (cc) as Fig.b. Fig.c. 4 Put the cap on the Guide Block(A) as Fig.e. Fig.a Fig.
Guide Block (A) installed on stone bathtub 1.Remove the cap from the Guide Block(A). 2.Ensure the Stationary Glass(O) is plumb. Using a pencil or other marking tool, mark the holes as Fig.a 3.Drill one hole and insert the Wall Anchor (dd). Attach the Guide Block(A) using ST4 x 30 Screws (cc) as Fig.b. Fig.c. Fig.d. 4 Put the cap on the Guide Block(A) as Fig.e. Fig.a Fig.b CAUTION: When cutting or drilling . .
Glass Door (E) Installation DO NOT install the towel bars on the glass until instructed. DO NOT lift the glass using the handle; 1. Insert the Glass Door(E) into the Guide Block(A) as Fig.a; 2.From inside of enclosure, carefully, and with assistance from another capable person, hang sliding Glass Door(E) and Roller (I) onto Upper Guide Fig.b ; 3.
U Channel(C) & Magnetic Strip(D) Installation 1.Check the threshold for level and the Glass Door(E) for plumb. 2.Check the Glass Door(E) to make sure it moves smoothly. 3.Using a pencil or other marking tool, mark the projection of the U Channel(C) on the door wall .
U Channel(C) & Magnetic strip(D) Installation es Ifa stud is presented behind the wall: drill a pilot hole into the stud and use the ST4.0 x 30mm Screws (bb) stud is presented behind the wall: drill a hole and insert the Wall Anchors (aa) and use the ST4.0 x 30mm Screws (bb). Inside View 1.Ensure the U channel(C) is plumb. Using a pencil or other marking tool, mark the holes as Fig.a 2.Drill four holes and insert the Wall Anchor (dd). Attach the U channel(C) using ST4 x 30 Screws (bb) as Fig.b. Fig.c. 3.
Roller Guard(H) Installation Attach the Roller Guard (H) to the Glass Door(E) to prevent the door glass from being lifted off of the Upper Guide Rail (K). Adjust the Roller Guard (H) to within 1/32" beneath the Upper Guide Rail (K). ~ 1 outside Inside Stationary Glass(0) \_ Drawing Not to Scale J ? outside Inside Stationary Glass(O) Roller Guard yp .
Handle(F) Installation Attach the Handle (F) to the Glass Door (E) . Be sure to use all of the supplied rubber gaskets to protect the glass.
Alu. Threshold(B) Installation Measure "X" and cut the Alu. Threshold (B) same length as "X" wall to Guide Block(A). Use Painter’s Tape to hold the Water seal tight in position while the silicone cures.
16 SEALING A The surfaces need to be clean and free of debris before applying silicone. Ensure that the Shower door closes tightly and opens smoothly. “ETL Apply a good quality silicone sealant along the U channel(C) and Guide Block (A) and bottom of Stationary Glass(O) and Wall Jamb(N). AH Now 24 hours for the silicone to cure before using the shower. Apply Silicone supplied). Apply silicone around the Alu. Threshold(B). 17 Complete.