VAUXHALL Astra 0-1 VAUXHALL Astra Owner’s Manual Model Year 2012 Edition: July 2011 TS 1680-A-12
Contents Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 19 Seats, restraints ........................... 35 Storage ........................................ 53 Instruments and controls ............. 91 Lighting ...................................... 125 Climate control ........................... 135 Driving and operating ................. 143 Vehicle care ...............................
2 Introduction Introduction
Introduction Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate. Introduction Your vehicle is a designed combination of advanced technology, safety, environmental friendliness and economy. This Owner's Manual provides you with all the necessary information to enable you to drive your vehicle safely and efficiently.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage. Symbols Page references are indicated with 3. 3 means "see page". Thank you for choosing a Vauxhall. We wish you many hours of pleasurable driving.
Introduction 5
6 In brief In brief Vehicle unlocking Seat adjustment Seat positioning Initial drive information Press button c to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, push the touchpad switch below the handle. Radio remote control 3 20, Central locking system 3 21, Load compartment 3 24. Pull handle, slide seat, release handle. Seat position 3 37, Seat adjustment 3 37.
In brief 7 Seat backrests Seat height Seat inclination Pull lever, adjust inclination and release lever. Allow the seat to engage audibly. Seat position 3 37, Seat adjustment 3 37. Lever pumping motion up = seat higher down = seat lower Lever pumping motion up = front end higher down = front end lower Seat position 3 37, Seat adjustment 3 37. Seat position 3 37, Seat adjustment 3 37.
8 In brief Head restraint adjustment Seat belt Mirror adjustment Interior mirror Press the button, adjust height and engage. Head restraints 3 35. Pull out the seat belt and engage in belt buckle. The seat belt must not be twisted and must fit close against the body. The backrest must not be tilted back too far (maximum approx. 25 °). To release belt, press red button on belt buckle. Seat position 3 37, Seat belts 3 41, Airbag system 3 44.
In brief Exterior mirrors Steering wheel adjustment Select the relevant exterior mirror and adjust it. Convex exterior mirrors 3 28, Electric adjustment 3 28, Folding exterior mirrors 3 28, Heated exterior mirrors 3 29. Unlock the lever, adjust the steering wheel, then engage the lever and ensure it is fully locked. Do not adjust the steering wheel unless the vehicle is stationary and the steering wheel lock has been released. Airbag system 3 44, Ignition positions 3 144.
10 In brief Instrument panel overview
In brief 1 Light switch ........................ 125 Headlight range adjustment ......................... 127 Front fog lights ................... 130 Rear fog light ...................... 131 Instrument illumination ....... 132 2 Side air vents ...................... 141 3 Turn and lane-change signals, headlight flash, low beam and high beam ... 130 Exit lighting ......................... 133 Parking lights ...................... 131 Driver Information Centre .... 109 4 Cruise control ....................
12 In brief Exterior lighting Press light switch > = front fog lights r = rear fog light Headlight flash, high beam and low beam Lighting 3 125.
In brief Turn and lane-change signals Hazard warning flashers Horn lever up = right turn signal lever down = left turn signal Operated with the ¨ button. Hazard warning flashers 3 130. Press j. Turn and lane-change signals 3 130, Parking lights 3 131.
14 In brief Washer and wiper systems Windscreen wiper 2 = fast 1 = slow P = timed interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down. Windscreen wiper 3 93, Wiper blade replacement 3 181. Windscreen and headlight washer systems Rear window wiper and washer systems Pull lever. Windscreen and headlight washer system 3 93, Washer fluid 3 178.
In brief Climate control Heated rear window, heated exterior mirrors Push lever. Washer fluid is sprayed on the rear window and the wiper wipes a few times. The heating is operated by pressing the Ü button. Heated rear window 3 32. Demisting and defrosting the windows Press button V. Set the temperature control to the highest level. Cooling n on. Heated rear window Ü on. Climate control system 3 135.
16 In brief Transmission Automatic transmission Manual transmission Reverse: with the vehicle stationary, depress the clutch pedal, press the release button on the selector lever and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection. Manual transmission 3 153. Starting off Check before starting off P R N D = = = = park reverse neutral drive Manual mode: move selector lever from D to the left.
In brief Starting the engine ■ Turn key to position 1 ■ move the steering wheel slightly to release the steering wheel lock ■ operate clutch and brake ■ automatic transmission in P or N ■ do not operate accelerator pedal ■ diesel engines: turn the key to position 2 for preheating and wait until control indicator ! goes out ■ turn key to position 3 and release Starting the engine 3 144.
18 In brief selector lever to P before switching off the ignition. Turn the front wheels towards the kerb. ■ Lock the vehicle with button e on the radio remote control. Activate the anti-theft alarm system 3 25. ■ Do not park the vehicle on an easily ignitable surface. The high temperature of the exhaust system could ignite the surface. ■ Close the windows and the sunroof. ■ The engine cooling fans may run after the engine has been switched off 3 175.
Keys, doors and windows Keys, doors and windows Keys, locks ................................... 19 Doors ........................................... 24 Vehicle security ............................ 25 Exterior mirrors ............................ 28 Interior mirrors ............................. 29 Windows ...................................... 30 Roof .............................................
20 Keys, doors and windows Radio remote control Handle with care, protect from moisture and high temperatures and avoid unnecessary operation. Fault Used to operate: ■ Central locking system ■ Anti-theft locking system ■ Anti-theft alarm system ■ Power windows ■ Sunroof The radio remote control has an approximate range of up to 20 metres. It can be restricted by external influences. The hazard warning flashers confirm operation.
Keys, doors and windows Key with foldaway key section Extend the key and open the unit. Replace the battery (battery type CR 2032), paying attention to the installation position. Close the unit and synchronise. Radio remote control synchronisation After replacing the battery, unlock the door with the key in the driver's door lock. The radio remote control will be synchronised when you switch on the ignition.
22 Keys, doors and windows Unlocking The setting can be saved for the key being used. Memorised settings 3 21. Locking Close doors, load compartment and fuel filler flap. Press button c. Two settings are selectable: ■ To unlock only the driver's door, load compartment and fuel filler flap, press button c once. To unlock all doors, press button c twice or ■ press button c once to unlock all doors, load compartment and fuel filler flap The setting can be changed in the menu Settings in the Info-Display.
Keys, doors and windows Fault in radio remote control system Unlocking Manually unlock the driver's door by turning the key in the lock. Switch on the ignition and press the central locking button c to unlock all doors, load compartment and fuel filler flap. By switching on the ignition, the antitheft locking system is deactivated. Locking Manually lock the driver's door by turning the key in the lock.
24 Keys, doors and windows 9 Warning Use the child locks whenever children are occupying the rear seats. Using a key or suitable screwdriver, turn the child lock in the rear door to the horizontal position. The door cannot be opened from the inside. For deactivation turn the child lock to the vertical position. Doors Closing Load compartment Tailgate Opening Use one of the interior handles. Do not push the touchpad switch below the handle whilst closing as this will unlock the tailgate again.
Keys, doors and windows General hints for operating tailgate 9 Warning Do not drive with the tailgate open or ajar, e.g. when transporting bulky objects, since toxic exhaust gases, which can not be seen or smelled, could enter the vehicle. This can cause unconsciousness and even death. Caution Before opening the tailgate check overhead obstructions, such as a garage door, to avoid damage to the tailgate. Always check the moving area above and behind the tailgate.
26 Keys, doors and windows Activation ■ Self-activated 30 seconds after locking the vehicle (initialisation of the system) ■ Directly by pressing e on the radio remote control once more after locking Activation without monitoring of passenger compartment and vehicle inclination Note Changes to the vehicle interior such as the use of seat covers, and open windows or sunroof, could impair the function of passenger compartment monitoring. 1. Close tailgate, bonnet, windows and sunroof. 2. Press button o.
Keys, doors and windows Status during the first 30 seconds of anti-theft alarm system activation: LED = test, arming delay. illuminates LED flashes = doors, tailgate or quickly bonnet not completely closed, or system fault. Status after system is armed: LED flashes = system is armed. slowly Seek the assistance of a workshop in the event of faults. Deactivation Unlocking the vehicle deactivates the anti-theft alarm system.
28 Keys, doors and windows Exterior mirrors In position 0 no mirror is selected. Convex shape Folding Electric folding The convex exterior mirror contains an aspherical area and reduces blind spots. The shape of the mirror makes objects appear smaller, which will affect the ability to estimate distances. Electric adjustment For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force.
Keys, doors and windows Heated Interior mirrors Automatic anti-dazzle Manual anti-dazzle Operated by pressing the Ü button. Heating works with the engine running and is switched off automatically after a short time. Dazzle from following vehicles at night is automatically reduced. To reduce dazzle, adjust the lever on the underside of the mirror housing.
30 Keys, doors and windows Windows Windscreen Heat-reflecting windscreen The heat-reflecting windscreen has a coating which reflects solar radiation. Also data signals, e.g. from toll stations, might be reflected. payment must be attached in these areas. Otherwise data recording malfunctions may occur. Manual windows The door windows can be opened or closed with the window winders. Power windows 9 Warning The marked areas of the windscreen behind the interior mirror are not covered with the coating.
Keys, doors and windows Safety function If the window glass encounters resistance above the middle of the window during automatic closing, it is immediately stopped and opened again. 31 Child safety system for rear windows Override safety function In the event of closing difficulties due to frost or the like, switch on the ignition, then pull the switch to the first detent and hold. The window moves up without safety function enabled. To stop movement, release the switch.
32 Keys, doors and windows Initialising the power windows If the windows cannot be closed automatically (e.g. after disconnecting the vehicle battery), a warning message or a warning code is displayed in the Driver Information Centre. Vehicle messages 3 113. Activate the window electronics as follows: 1. Close doors. 2. Switch on ignition. 3. Pull switch until the window is closed and keep pulling for additional 2 seconds. 4. Repeat for each window. Heated rear window Operated by pressing the Ü button.
Keys, doors and windows Roof 33 Raise or close Press q or r: sunroof is raised or closed automatically with safety function enabled. If the sunroof is raised, it can be opened in one step by pressing p. Sunroof 9 Warning Take care when operating the sunroof. Risk of injury, particularly to children. Keep a close watch on the movable parts when operating them. Ensure that nothing becomes trapped in them as they move. Switch on ignition to operate the sunroof.
34 Keys, doors and windows Closing sunroof from outside The sunroof can be closed remotely from outside the vehicle. Press and hold e button to close the sunroof. Release the button to stop the movement. Initialising after a power failure After a power failure, it may only be possible to operate the sunroof to a limited extent. Have the system initialised by your workshop.
Seats, restraints Seats, restraints Head restraints ............................ 35 Front seats ................................... 37 Rear seats ................................... 40 Seat belts ..................................... 41 Airbag system .............................. 44 Child restraints ............................. 48 Head restraints 35 Adjustment Head restraints on front seats Position 9 Warning Only drive with the head restraint set to the proper position.
36 Seats, restraints Horizontal adjustment Head restraints on rear seats forwards. Thus the head is supported so that the risk of whiplash injury is reduced. Note Approved accessories may only be attached if the seat is not in use. To adjust horizontally, pull the head restraint forwards. It engages in several positions. To return to its rearmost position, pull fully forwards and release.
Seats, restraints Front seats Seat position 9 Warning Only drive with the seat correctly adjusted. ■ Sit with buttocks as far back against the backrest as possible. Adjust the distance between the seat and the pedals so that legs are slightly angled when pressing the pedals. Slide the front passenger seat as far back as possible. ■ Sit with shoulders as far back against the backrest as possible. Set the backrest rake so that it is possible to easily reach the steering wheel with arms slightly bent.
38 Seats, restraints Seat positioning Seat backrests Seat height Pull handle, slide seat, release handle. Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly.
Seats, restraints Seat inclination Lumbar support Adjustable thigh support Lever pumping motion up = front end higher down = front end lower Adjust lumbar support using the fourway switch to suit personal requirements. Moving support up and down: push switch up or down. Increasing and decreasing support: push switch forwards or backwards. Pull the lever and slide the thigh support.
40 Seats, restraints Armrest Heating Rear seats Armrest The armrest can be slid forwards by 10 cm. Under the armrest there is a storage compartment. Armrest storage 3 55. Adjust heating to the desired setting by pressing the ß button for the respective seat one or more times. The control indicator in the button indicates the setting. Prolonged use of the highest setting for people with sensitive skin is not recommended. Seat heating is operational when engine is running and during an Autostop.
Seats, restraints Seat belts The seat belts are locked during heavy acceleration or deceleration of the vehicle holding the occupants in the sitting position. Therefore the risk of injury is considerably reduced. 9 Warning Fasten seat belt before each trip. In the event of an accident, people not wearing seat belts endanger their fellow occupants and themselves. Seat belts are designed to be used by only one person at a time. They are not suitable for people smaller than 150 cm.
42 Seats, restraints Three-point seat belt Height adjustment Fastening Withdraw the belt from the retractor, guide it untwisted across the body and insert the latch plate into the buckle. Tighten the lap belt regularly whilst driving by pulling the shoulder belt. Seat belt reminder 3 103. Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body.
Seats, restraints Removing Adjust the height so that the belt lies across the shoulder. It must not lie across the throat or upper arm. Do not adjust while driving. To release belt, press red button on belt buckle. Seat belts on the rear seats The seat belt for the rear centre seat can only be withdrawn from the retractor if the backrest is in the rear position.
44 Seats, restraints Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision. 9 Warning If handled improperly the airbag systems can be triggered in an explosive manner. Note The airbag systems and belt pretensioner control electronics are located in the centre console area.
Seats, restraints 45 Fit the seat belt correctly and engage securely. Only then the airbag is able to protect. Side airbag system The inflated airbags cushion the impact, thereby reducing the risk of injury to the upper body and head of the front seat occupants considerably. 9 Warning Optimum protection is only provided when the seat is in the proper position 3 37. Keep the area in which the airbag inflates clear of obstructions.
46 Seats, restraints Curtain airbag system The curtain airbag system consists of an airbag in the roof frame on each side. This can be identified by the word AIRBAG on the roof pillars. The curtain airbag system is triggered in the event of a side-on impact of a certain severity. The ignition must be switched on. 9 Warning Keep the area in which the airbag inflates clear of obstructions.
Seats, restraints Use the ignition key to choose the position: * = front passenger airbag is deactivated and will not inflate in the event of a collision. Control indicator * illuminates continuously in the centre console. A child restraint system can be installed in accordance with the chart Child restraint installation locations 3 49. No adult person is allowed to occupy the front passenger seat. V = front passenger airbag is active. A child restraint system must not be installed.
48 Seats, restraints Child restraints Child restraint systems We recommend the Vauxhall child restraint system which is tailored specifically to the vehicle. When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system. Always comply with local or national regulations. In some countries, the use of child restraint systems is forbidden on certain seats.
Seats, restraints 49 Child restraint installation locations Permissible options for fitting a child restraint system On front passenger seat Weight and age class activated airbag deactivated airbag On rear outboard seats On rear centre seat Group 0: up to 10 kg or approx. 10 months X U1 U2 U Group 0+: up to 13 kg or approx. 2 years X U1 U2 U Group I: 9 to 18 kg or approx. 8 months to 4 years X U1 U2 U Group II: 15 to 25 kg or approx.
50 Seats, restraints Permissible options for fitting an ISOFIX child restraint system Weight class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat Group 0: up to 10 kg E ISO/R1 X IL X Group 0+: up to 13 kg E ISO/R1 X IL X D ISO/R2 X IL X C ISO/R3 X IL X D ISO/R2 X IL X C ISO/R3 X IL X B ISO/F2 X IL, IUF X B1 ISO/F2X X IL, IUF X A ISO/F3 IL, IUF X Group I: 9 to 18 kg IL X = Suitable for particular ISOFIX restraint sy
Seats, restraints ISOFIX size class and seat device A – ISO/F3 B – ISO/F2 B1 – ISO/F2X C – ISO/R3 D – ISO/R2 E – ISO/R1 = = = = = = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg. Rear-facing child restraint system for children of maximum size in the weight class up to 13 kg.
52 Seats, restraints ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Specific vehicle ISOFIX child restraint system positions are marked in the table by IL. ISOFIX mounting brackets are indicated by a label on the backrest. Top-tether fastening eyes Top-Tether fastening eyes are marked with the symbol : for a child seat. In addition to the ISOFIX mounting fasten the Top-Tether strap to the Top-Tether fastening eyes.
Storage Storage Storage compartments 53 Cupholders Glovebox Storage compartments ................ 53 Load compartment ....................... 74 Roof rack system ......................... 88 Loading information ..................... 89 The glovebox features a pen holder, a credit card holder and a coin holder. The glovebox should be closed whilst driving. Cupholders are located in the centre console.
54 Storage Depending on the version, cupholders are located under a cover in the centre console. Slide cover backwards. Bottles can be stowed after folding up the intermediate shelf 3 56. Additional cupholders are located in the rear armrest. Fold down the armrest. Front storage Sunglasses storage A storage compartment is located next to the steering wheel. Fold down and open. Do not use for storing heavy objects.
Storage Underseat storage Armrest storage 55 Storage in the rear armrest Storage under the front armrest Press button in the recess and pull out drawer. Maximum load: 3 kg. To close, push in and engage. Depending on the version, the tyre repair kit is stowed in the drawer. Tyre repair kit 3 202. Press button to fold up the armrest. The armrest must be in rearmost position. Fold down armrest and open cover. Close cover before folding the armrest up.
56 Storage Centre console storage A further storage compartment is located under the intermediate shelf. Fold up the intermediate shelf and fix it in the vertical position. The frame of the cupholder can be reintegrated to stow bottles. Front console Rear console The storage container can be used to store small items. Depending on the version, a storage compartment is located under a cover. Slide cover backwards. Press button to remove the frame of the cupholder.
Storage Rear carrier system Rear carrier system for two bicycles 57 There must not be any objects on the bicycles that could become loose during transportation. Caution Do not attach bicycles with carbon pedal cranks to bicycle carriers. The bicycles might get damaged. Extending Open the tailgate. 9 Warning The rear carrier system (Flex-Fix system) allows bicycles to be attached to a pull-out carrier integrated into the vehicle floor. The transportation of other objects is not permitted.
58 Storage Completely pull out the rear carrier system until you hear it engage. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again Install the tail lamps Open out the lamp support on the back of the tail lamp completely. 9 Warning It is only permissible to fit objects to the rear carrier system if the system has been correctly engaged. If the rear carrier system will not engage correctly, do not fit objects to the system and slide the system back.
Storage 59 Lock the rear carrier system Check the cable and lamp position to make sure these are correctly installed and are securely located. Swivel the right clamping lever (1) first, followed by the left clamping lever (2), until a resistance is noticeable. The rear carrier system is locked when the clamping levers are swivelled by approx. 50°. Otherwise safe functionality is not guaranteed. Note Close the tailgate.
60 Storage Unfold pedal crank recesses Fold one or both pedal crank recesses upwards until the diagonal support engages. Adapting the rear carrier system to a bicycle Remove the pedal crank mounts from the pedal crank recesses. Press the release lever and withdraw the wheel recesses.
Storage Push the release lever on the strap retainer and remove the strap retainer. Prepare the bicycle for attachment 61 The rear bicycle must have its front wheel facing right. Attaching a bicycle to the rear carrier system If the bicycle has curved pedal cranks, screw in the pedal crank unit all the way (position 1). Note The maximum width for the pedal crank is 38.3 mm and the maximum depth is 14.4 mm. Rotate the left pedal (without a chain cog) vertically downwards.
62 Storage Put on the bicycle. The pedal crank here must be placed in the pedal crank recess opening as shown in the illustration. Place the wheel recesses such that the bicycle is more or less horizontal. Here, the distance between the pedals and the tailgate should be at least 5 cm. Both bicycle tyres must be in the wheel recesses. Caution Make sure that the pedal does not touch the surface of the rear end carrier. Otherwise the crankset might be damaged during the transport.
Storage If the two bicycles obstruct one another, the relative positions of the bicycles can be adapted by adjusting the wheel recesses and the rotary lever on the pedal crank recess until the bicycles no longer touch one another. Make sure there is sufficient clearance from the vehicle. Tighten the attachment screw for the pedal bearing mount to its maximum point by hand. Secure both bicycle wheels to the wheel recesses using the strap retainers. Check the bicycle to make sure it is secure.
64 Storage Retracting the rear carrier system Push the pedal crank mounts into the pedal crank recess like shown in the graphic. Insert the strap retainer and pull tightly downwards as far as possible. Press release lever and slide in wheel recesses all the way as far as they will go. Disengage the locking lever on the diagonal support and fold both pedal crank recesses down. 9 Warning Risk of pinching.
Storage 65 Push the clamping lever down and pull both lamp supports out of the recesses. Swivel first the left clamping lever (1), followed by the right clamping lever (2), until they stop. Fold in the lamp supports on the backs of the tail lamps. First place the front (1) tail lamp, then the rear (2) tail lamp in the recesses and push down as far as possible. Push cables all the way into all guides in order to prevent damage. Open the tailgate.
66 Storage Rear carrier system for four bicycles powered bicycles to the pull-out carrier. The maximum load per bicycle on the adapter is 20 kg. If not in use, the carrier system must be slid back into the vehicle floor. There must not be any objects on the bicycles that could become loose during transportation. 9 Warning No-one should be in the extension zone of the rear carrier system, risk of injury.
Storage Completely pull out the rear carrier system until you hear it engage. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again. 9 Warning It is only permissible to fit objects to the rear carrier system if the system has been correctly engaged. If the rear carrier system will not engage correctly, do not fit objects to the system and slide the system back. Seek the assistance of a workshop.
68 Storage Swivel both clamping levers sidewards as far as they will go. Otherwise safe functionality is not guaranteed. Assembling the bicycle rack Fold out wheel recesses Lift the rack at the rear (1) and pull it backwards. Fold up the rack (2). Fold out both wheel recesses. Push down the rack (1) and swivel handle (2) backwards to engage.
Storage 69 1. Rotate the pedals into position as shown in the illustration and put the bicycle on the foremost wheel recess. Make sure that the bicycle stands centrally on the wheel recesses. 3. Secure both bicycle wheels to the wheel recesses using the strap retainers. 4. Check the bicycle to make sure it is secure. 2. Attach the short mounting bracket to the bicycle frame. Turn the knob clockwise to fasten.
70 Storage 2. Turn the lever (1) backwards and hold, then lower the adapter (2) at the rear. 3. Release lever and check if the adapter is engaged securely. 4. Guide the strap attached to the adapter underneath the lever for folding back the rear carrier system. Fasten the strap. Attaching further bicycles The attachment of further bicycles is similar to the attachment of the first bicycle. Additionally some steps must be considered: 1.
Storage 71 ■ Without attached adapter: It is recommended to attach a warning sign at the rearmost bicycle to increase visibility. Fold the rear carrier system backwards The rear carrier system can be folded backwards to get access to the load compartment. Push the lever (1) to disengage and hold. Pull the rack (2) backwards to fold the rear carrier system. ■ With attached adapter: 9 Warning Take care when disengaging the rear carrier system as it will tilt backwards. Risk of injury.
72 Storage Disassembling the bicycle rack Removing bicycles Undo strap retainers on both bicycle tyres. Turn knob anti-clockwise and remove mounting brackets. Detaching adapter Detach the adapter before removing the last bicycle left on the rear carrier system. 1. Fold in wheel recesses. 3. Turn the lever (1) backwards and hold. 4. Lift the adapter (2) at the rear and remove. 2. Unbutton the strap. Arrange mounting brackets as shown in the illustration.
Storage 73 Swivel both clamping levers inwards as far as they will go. Fold in tail lamps Swivel in both tail lamps. Fold in number plate holder Lift the number plate holder and fold it forwards. Retracting the rear carrier system Fold the rack backwards, then push forwards until it stops (1). Press the rack down at the rear (2). Fold in wheel recesses Fold in both wheel recesses. Stow the strap retainers accurately.
74 Storage Load compartment The rear seat backrest is divided into two parts. Both parts can be folded down. Load compartment extension, 5-door hatchback Pull release lever up and push the rear carrier system in the bumper until you hear it engage. Guide the seat belts through side supports to protect them against damage. When folding the backrests, pull the seat belts along with them. Pull the release lever on one or both sides and fold down the backrests onto the seat cushion.
Storage Ensure that the seat belts of the outboard seats are placed in the corresponding belt guides. 9 Warning Only drive the vehicle if the backrests are securely locked into position. Otherwise there is a risk of personal injury or damage to the load or vehicle in the event of heavy braking or a collision. 75 Load compartment extension, Sports tourer Folding down rear backrests Remove the load compartment cover if necessary. Press and hold the catch, then push the head restraints down.
76 Storage Pull the release lever on one or both sides and fold down the backrests onto the seat cushion. On vehicles with electric seat folding, the rear seats can also be folded from the load compartment. 9 Warning Take care when operating the electric foldable rear seats. The seat backrest is folded with considerable power. Risk of injury, particularly to children. Ensure that nothing is attached to the rear seats or located on the seat cushion.
Storage 9 Warning Raise the seat cushion and fold the backrest 77 Remove the seat cushion Only drive the vehicle if the backrests are securely locked into position. Otherwise there is a risk of personal injury or damage to the load or vehicle in the event of heavy braking or a collision. The seat belt of the centre seat could be blocked when the backrest is folded up too quickly. To unlock the retractor, push in the seat belt or pull it out by approx. 20 mm and then let go.
78 Storage To attach, apply seat cushion as shown in the illustration and engage both levers. Open the pass-through in the rear centre backrest Fold down the rear armrest. Pull the grip and open the cover. Suitable for loading long, narrow objects. Ensure that the cover engages after folding up. The closed cover can be secured from the side of the load compartment.
Storage 5-door hatchback Removing Lift cover at the rear and push it upwards at the front. Remove the cover. If the height adjustable cover is mounted in the middle or upper position, the load compartment cover can be stowed below it. Height adjustable cover 3 81. 79 Opening cover Fitting Engage cover in side guides and fold downwards. Attach retaining straps to tailgate. Sports tourer Unhook retaining straps from tailgate.
80 Storage Cover in upper position Push the handle at the end of the cover downwards. The rear of the cover is guided upwards automatically. Removing cover Open the load compartment cover. Pull the release lever on the right side up and hold it. Lift the cover first on the right side and remove from retainers. The removed cover can be stored under the rear floor cover like shown in the graphic. Rear floor storage cover 3 81.
Storage Rear floor storage cover Rear floor cover, 5-door hatchback The rear floor cover can be lifted and hooked in with the loop. Caution Only use the hook for hanging up the rear floor cover and the height adjustable cover. Height adjustable cover, 5-door hatchback The height adjustable cover can be mounted in three positions: ■ directly above the rear floor cover (1), ■ in a middle position (2) ■ in an upper position (3).
82 Storage Lowering To lower the cover, pull the strap backwards and push down the front centre of the cover at the same time. Caution Do not lower the height adjustable cover to position 1 in vehicles equipped with subwoofer. The subwoofer could be damaged. Note ■ If mounted in position 2 or 3, the space between the rear floor cover and the height adjustable cover can be used as a stowage compartment.
Storage Lashing eyes 83 ■ hooks, ■ service box, ■ strap set. The components are fitted in rails on both side panels using adapters and hooks. Installation of adapters in the rails Insert the bar into the recesses at the sidewalls. Caution Insert the bar into the rearmost recess when transporting heavy objects in the load compartment. Otherwise the rear floor cover might be damaged. The lashing eyes are designed to secure items against slippage, e.g. using lashing straps or luggage net.
84 Storage plate upwards to lock the adapter. To remove, turn the handle plate down and move out of the rail. Net pocket Installation of hooks in the rails Insert adapters into the required position in the rails. The net pocket can be suspended from the adapters. Insert the hook in the desired position first in the upper groove of the rail and then press in the lower groove. To remove, first pull out of the upper groove. Variable partition net Insert adapters into the required position in the rails.
Storage Strap set Service box Install two hooks in the upper rail. Insert the upper brackets of the box from above into the hooks. 85 Alternatively install both hooks in the lower rail. Plug in the lower brackets of the box from above into the lower hooks. Insert the adapters of the strap set in a rail. Make sure that the belt is not twisted. The strap set has two locks to open. The belt can be tightened.
86 Storage Passengers must not be transported behind the safety net. Behind the front seats Installation of the rod Attach strap to eyes underneath the rear seat cushion. Fold backrests forward. To get a flat load bay, first fold seat cushion before attaching the safety net. Move front seats forward to ease tension if necessary. There are two installation openings in the roof frame: suspend and engage rod of net at one side, compress rod and suspend and engage at other side. Load compartment 3 74.
Storage Warning triangle Sports tourer 5-door hatchback Stow the warning triangle in the space behind the strap on the right side of the load compartment. 87 First aid kit 5-door hatchback Fold down straps. Stow the warning triangle in the space behind the straps on the inside of the tailgate. Stow the first aid kit in the stowage compartment behind the warning triangle. Before first use, press in the interior trim at the top and at the sides of the perforation.
88 Storage Sports tourer Roof rack system Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended. Follow the installation instructions and remove the roof rack when not in use. Detach the cover from each mounting point by using a coin. Sports tourer with roof railing Mounting roof rack Fold down strap. Stow the first aid kit in the space behind a strap on the inside of the tailgate.
Storage Loading information ■ Heavy objects in the load compartment should be placed against the seat backrests. Ensure that the backrests are securely engaged. If objects can be stacked, heavier objects should be placed at the bottom. ■ Secure objects with lashing straps attached to the lashing eyes 3 83. Attach the height adjustable cover in the lowest position (1) 3 81. ■ Use the four hooks at the sidewalls of the load compartment for hanging up carrier bags. Maximum load: 5 kg per hook.
90 Storage vehicle weight (see identification plate 3 220) and the EC kerb weight. To calculate the payload, enter the data for your vehicle in the Weights table at the front of this manual. The EC kerb weight includes weights for the driver (68 kg), luggage (7 kg) and all fluids (tank 90 % full). Optional equipment and accessories increase the kerb weight.
Instruments and controls Instruments and controls Controls 91 Steering wheel controls Steering wheel adjustment Controls ....................................... 91 Warning lights, gauges and indicators ..................................... 98 Information displays ................... 109 Vehicle messages ...................... 113 Trip computer ............................. 117 Vehicle personalisation ..............
92 Instruments and controls Heated steering wheel Activate heating by pressing * button. Activation is indicated by the LED in the button. Horn The recommended grip areas of the steering wheel are heated quicker and to a higher temperature than the other areas. Heating is operational when the engine is running and during an Autostop. Stop-start system 3 146. Press j.
Instruments and controls Windscreen wiper/washer Adjustable wiper interval Automatic wiping with rain sensor Wiper lever in position P. Turn the adjuster wheel to adjust the desired wipe interval: short = turn adjuster wheel interval upwards long = turn adjuster wheel interval downwards P = automatic wiping with rain sensor 93 Windscreen wiper 2 1 P § = = = = fast slow interval wiping off For a single wipe when the windscreen wiper is off, press the lever down.
94 Instruments and controls Windscreen and headlight washer Adjustable sensitivity of the rain sensor Keep the sensor free from dust, dirt and ice. Turn the adjuster wheel to adjust the sensitivity: low = turn adjuster wheel sensitivity downwards high = turn adjuster wheel sensitivity upwards Pull lever. Washer fluid is sprayed onto the windscreen and the wiper wipes a few times.
Instruments and controls Rear window wiper/washer 95 The rear window washer system is deactivated when the fluid level is low. Outside temperature Press the rocker switch to activate the rear window wiper: upper = continuous position operation lower = intermittent position operation middle = off position Push lever. Washer fluid is sprayed onto the rear window and the wiper wipes a few times. Do not use if the rear window is frozen. Switch off in car washes.
96 Instruments and controls Set date and time Press the CONFIG button. The menu Settings is displayed. Select Time & Date. If outside temperature drops to 3 °C, a warning message is displayed in the Driver Information Centre with Uplevel-Display. 9 Warning The road surface may already be icy even though the display indicates a few degrees above 0 °C. Clock Date and time are shown in the Info-Display. Selectable setting options: ■ Set time: Changes the time shown on the display.
Instruments and controls Power outlets A 12 Volt power outlet is located in the front console. A further 12 Volt power outlet is located in the rear console. Fold the cover downwards. Sports tourer: A 12 Volt power outlet is located at the left sidewall in the load compartment. Do not exceed the maximum power consumption of 120 watts. With ignition off, the power outlets are deactivated. Additionally the power outlets are deactivated in the event of low battery voltage.
98 Instruments and controls Warning lights, gauges and indicators Odometer Instrument cluster In some versions, the needles of the instruments briefly rotate to the end position when the ignition is switched on. Speedometer The portable ashtray can be placed in the cupholders. The bottom line displays the recorded distance in miles. Trip odometer The top line displays the recorded distance since the last reset. To reset, hold the reset knob depressed for a few seconds with the ignition on.
Instruments and controls Tachometer Fuel gauge Displays the engine speed. Drive in a low engine speed range for each gear as much as possible. Displays the fuel level in the tank. Control indicator i illuminates if the level in the tank is low. Refuel immediately if it flashes. Never run the tank dry. Because of the fuel remaining in the tank, the top-up quantity may be less than the specified tank capacity.
100 Instruments and controls Caution If engine coolant temperature is too high, stop vehicle, switch off engine. Danger to engine. Check coolant level. Service display The engine oil life system lets you know when to change the engine oil and filter. Based on driving conditions, the interval at which an engine oil and filter change will be indicated can vary considerably. In the Uplevel-Display, the remaining oil life duration is displayed in the Vehicle Information Menu.
Instruments and controls indicators may vary. When the ignition is switched on, most control indicators will illuminate briefly as a functionality test.
102 Instruments and controls Control indicators in the instrument cluster
Instruments and controls Control indicators in the centre console Bulb replacement 3 182, Fuses 3 191. Turn signals 3 130. Seat belt reminder Seat belt reminder on front seats X for driver's seat illuminates or flashes red. k for front passenger seat illuminates or flashes red, when seat is occupied. Turn signal O illuminates or flashes green. Illuminates briefly The parking lights are switched on. Flashes A turn signal or the hazard warning flashers are activated.
104 Instruments and controls * illuminates yellow. The front passenger airbag is deactivated 3 46. 9 Danger Risk of fatal injury for a child using a child restraint system together with activated front passenger airbag. Risk of fatal injury for an adult person with deactivated front passenger airbag. Charging system p illuminates red. Illuminates when the ignition is switched on and goes out shortly after the engine starts. Illuminates when the engine is running Stop, switch off engine.
Instruments and controls Illuminates Brake pedal needs to be operated to release the electrical parking brake 3 155. Electrical parking brake fault Flashes Clutch pedal needs to be operated to start the engine 3 144. Illuminates Electrical parking brake Flashes m illuminates or flashes red. Illuminates Electrical parking brake is applied 3 155. Flashes Electrical parking brake is not fully applied or released.
106 Instruments and controls Illuminates with power steering disabled Failure in the power steering system. Consult a workshop. Lane departure warning ) illuminates green or yellow or flashes yellow. Illuminates green System is switched on and ready to operate. Illuminates yellow No lane marking is detected. Flashes yellow System recognizes an unintended lane change. Ultrasonic parking assist r illuminates yellow.
Instruments and controls Continue driving until % goes out. If possible, do not allow engine speed to drop below 2000 rpm. Illuminates The diesel particle filter is full. Start cleaning process as soon as possible. Flashes The maximum filling level of the filter is reached. Start cleaning process immediately to avoid damage to the engine. Diesel particle filter 3 148, Stop-start system 3 146. Tyre pressure monitoring system w illuminates or flashes yellow. Illuminates Tyre pressure loss.
108 Instruments and controls Flashes Fuel used up. Refuel immediately. Never run the tank dry. Catalytic converter 3 149. Bleeding the diesel fuel system 3 181. Immobiliser d flashes yellow. Fault in the immobiliser system. The engine cannot be started. Reduced engine power # illuminates yellow. The engine power is limited. Consult a workshop. Exterior light 8 illuminates green. The exterior lights are on 3 125. High beam C illuminates blue.
Instruments and controls 109 Information displays Driver Information Centre The Driver Information Centre (DIC) is located in the instrument cluster between speedometer and tachometer. It is available as Midlevel-Display or Uplevel-Display (base and extended version).
110 Instruments and controls Selecting menus and functions Press the SET/CLR button to select a function or to confirm a message. The menus and functions can be selected via the buttons on the turn signal lever. Vehicle Information Menu Press the MENU button to select the Vehicle Information Menu. Turn the adjuster wheel to select one of the submenus. Press the SET/ CLR button to confirm. Turn the adjuster wheel to highlight a menu option or to set a numeric value.
Instruments and controls ■ Remaining Oil Life: 3 100 ■ Speed Warning: If exceeding the preset speed, a warning chime will be activated Selection and indication can be different between Midlevel- and Uplevel-Display. Trip/Fuel Information Menu Press the MENU button to select the Trip/Fuel Information Menu. Turn the adjuster wheel to select one of the submenus. Press the SET/ CLR button to confirm.
112 Instruments and controls Colour-Info-Display ■ vehicle messages 3 113 ■ settings for vehicle personalisation 3 119 The type of information and how it is displayed depends on the equipment of the vehicle and the settings made. Selecting menus and settings Menus and settings are accessed via the display.
Instruments and controls Selecting with the Infotainment system Select a function via the Infotainment system buttons. The menu of the selected function is displayed. The multifunction knob is used to select an item and to confirm.
114 Instruments and controls Vehicle messages on the Midlevel-Display The vehicle messages are displayed as code numbers. No. Vehicle message 2 No radio remote control detected, depress clutch pedal for a restart No. Vehicle message No.
Instruments and controls 115 No. Vehicle message No. Vehicle message No.
116 Instruments and controls Vehicle messages on the Uplevel-Display The vehicle messages are displayed as text. Follow the instructions given in the messages.
Instruments and controls When the vehicle is parked and/ or the driver's door is opened ■ When the key is in the ignition switch. ■ With exterior lights on. If the battery cannot be recharged, have the cause of the fault remedied by a workshop. 117 Trip computer The menus and functions can be selected via the buttons on the turn signal lever. During an Autostop ■ If the driver's door is opened.
118 Instruments and controls Display. ECO drive assistant is only available on vehicles with extended Uplevel-Display.
Instruments and controls Additionally the control indicator i in the fuel gauge illuminates or flashes 3 107. Traffic sign assistant Average consumption ECO drive assistant Display of average consumption. The measurement can be reset at any time and starts with a default value. To reset, press the SET/CLR button for a few seconds. Indicates detected traffic signs for the current route section 3 162. Instantaneous consumption Display of the instantaneous consumption.
120 Instruments and controls Personal settings in the Graphic-Info-Display Press the CONFIG button. The menu Settings is displayed. The following settings can be selected by turning and pressing the multifunction knob: ■ Sport mode settings ■ Languages ■ Time Date ■ Radio settings ■ Phone settings ■ Vehicle settings In the corresponding submenus the following settings can be changed: Sport mode settings The driver can select the functions which will be activated in Sport mode 3 158.
Instruments and controls Phone settings See description for Infotainment system in the Infotainment system manual. Vehicle settings ■ Climate and air quality Auto fan speed: Modifies the fan regulation. Changed setting will be active after switching the ignition off and on again. Climate control mode: Activates or deactivates the cooling every time the ignition is switched on or uses the last chosen setting.
122 Instruments and controls Delayed door lock: Activates or deactivates the delayed door locking function. ■ Remote locking, unlocking, starting Remote unlock feedback: Activates or deactivates the hazard warning flasher feedback whilst unlocking. Remote door unlock: Changes the configuration to unlock only the driver's door or the whole vehicle whilst unlocking. Auto relock doors: Activates or deactivates the automatic relock function after unlocking without opening the vehicle.
Instruments and controls Sport mode settings The driver can select the functions which will be activated in Sport mode 3 158. ■ Sport suspension: Damping becomes harder. ■ Sport powertrain performance: Accelerator pedal and gear change characteristics become more responsive. ■ Sport steering: Steering support is reduced. ■ Swap backlight colour main instr.: Change of instrument illumination colour. Phone settings See description for Infotainment system in the Infotainment system manual.
124 Instruments and controls Rear auto wipe in reverse: Activates or deactivates automatically switching on of the rear window wiper when reverse gear is engaged. ■ Park assist / Collision detection Park assist: Activate or deactivate the ultrasonic parking assist. ■ Exterior ambient lighting Duration upon exit of vehicle: Activates or deactivates and changes the duration of exit lighting. Exterior lighting by unlocking: Activates or deactivates the welcome lighting.
Lighting Lighting Exterior lighting Light switch 125 On vehicles without automatic light control: 7 = off In the Driver Information Centre with Uplevel-Display, the current status of the automatic light control is displayed. When switching on the ignition, automatic light control is active. Control indicator 8 3 108. Exterior lighting .......................... 125 Interior lighting ........................... 132 Lighting features ........................
126 Lighting Automatic light control While the daytime running light is active, the tail lights are switched on or off depending on country-specific variant. High beam Automatic headlight activation During poor lighting conditions the headlights are switched on. Furthermore the headlights are switched on if the windscreen wipers have been activated for several wipes.
Lighting Headlight range adjustment Dynamic automatic headlight levelling 3 128. Manual headlight range adjustment Headlights when driving abroad 127 Vehicles with Xenon headlight system The asymmetrical headlight beam extends visibility at the edge of the road at the passenger side. However, when driving in countries where traffic drives on the opposite side of the road, adjust the headlights to prevent dazzling of oncoming traffic.
128 Lighting For deactivation operate the same procedure as described above. f will not flash when function is deactivated. Adaptive forward lighting The Adaptive forward lighting functions are only available with BiXenon headlights. Light range, light distribution and intensity of light are variably triggered depending on the light conditions, weather and road type. With the light switch in position AUTO all lighting functions are available.
Lighting Corner lighting On tight bends or when turning off, depending on the steering angle or the turn signal light, an additional left or right reflector is switched on which illuminates the road at a right angle to the direction of travel. It is activated up to a speed of 25 mph. Control indicator f 3 108. Reversing function If the headlights are on and reverse gear is engaged, both corner lights are switched on.
130 Lighting Hazard warning flashers Turn and lane-change signals When a trailer is connected, turn signal flashes six times when pressing the lever until resistance is felt and then releasing. Move the lever to the resistance point and hold for longer indication. Switch the turn signal off manually by moving the lever to its original position. Front fog lights Operated with the ¨ button. In the event of an accident with airbag deployment the hazard warning flashers are activated automatically.
Lighting Rear fog lights Parking lights 131 Reversing lights The reversing light comes on when the ignition is on and reverse gear is selected. Misted light covers The inside of the light housing may mist up briefly in poor, wet and cold weather conditions, in heavy rain or after washing. The mist disappears quickly by itself; to help switch on the headlights. Operated with the r button. Light switch in position AUTO: switching on rear fog light will switch headlights on automatically.
132 Lighting Interior lighting Instrument panel illumination control On vehicles with light sensor, the brightness can only be adjusted when the exterior lights are on and the light sensor detects night conditions. Interior lights During entry and exit of the vehicle, the front and rear courtesy lights automatically switch on and then off after a delay. Operate rocker switch: w = automatic switching on and off. press u = on. press v = off.
Lighting Reading lights Lighting features Spotlight incorporated in the interior lighting comes on when headlights are switched on. The following lights will additionally switch on when the driver's door is opened: ■ All switches ■ Driver Information Centre ■ Door pocket lights Entry lighting Exit lighting Centre console lighting Welcome lighting Operated with s and t buttons in front and rear courtesy lights. Sunvisor lights Illuminates when the cover is opened.
134 Lighting Switching on Activation, deactivation and duration of this function can be changed in the menu Settings in the Info-Display. Vehicle personalisation 3 119. The settings can be saved for the key being used 3 21. Battery discharge protection Battery state of charge function 1. Switch off ignition. 2. Remove ignition key. 3. Open driver's door. 4. Pull turn signal lever. 5. Close driver's door. If the driver's door is not closed the lights switch off after two minutes.
Climate control Climate control Climate control systems ............. 135 Air vents ..................................... 141 Maintenance .............................. 141 Climate control systems Heating and ventilation system 135 Heating will not be fully effective until the engine has reached normal operating temperature. Air distribution s = to windscreen and front door windows M = to head area via adjustable air vents K = to foot well All combinations are possible.
136 Climate control Air conditioning system The air conditioning system cools and dehumidifies (dries) as soon as the outside temperature is slightly above the freezing point. Therefore condensation may form and drip from under the vehicle. If no cooling or drying is required, switch the cooling system off to save fuel. When the cooling system is switched off, no engine restart will be requested by the climate control system during an Autostop.
Climate control Demisting and defrosting the windows V Note If the settings for demisting and defrosting are selected, an Autostop will be inhibited. If the settings for demisting and defrosting are selected while the engine is in an Autostop, the engine will restart automatically. Electronic climate control system The dual zone climate control allows different climatisation temperatures for driver and front passenger side.
138 Climate control Automatic mode AUTO All air vents are actuated automatically in automatic mode. The air vents should therefore always be open. Temperature preselection Temperatures can be set to the desired value. Each change of settings is shown in the Info-Display for a few seconds. The electronic climate control system is only fully operational when the engine is running. Basic setting for maximum comfort: ■ Press AUTO button, the air conditioning is activated automatically.
Climate control Note If the temperature is reduced 2 °C or more while the engine is in an Autostop, the engine will restart automatically. Stop-start system 3 146. Manual settings Climate control system settings can be changed by activating the buttons and rotary knobs as follows. Changing a setting will deactivate the automatic mode. Demisting and defrosting the windows V ■ Press button V. ■ Press cooling button n. ■ Temperature and air distribution are set automatically and the fan runs at high speed.
140 Climate control If no cooling or drying is required, switch the cooling system off to save fuel. When the cooling system is switched off, no engine restart will be requested by the climate control system during an Autostop. The display will indicate AC ON when cooling is activated or AC OFF when the cooling is deactivated. directed to it. If windscreen mists up from outside, activate windscreen wiper and deactivate s.
Climate control Air vents Maintenance Adjustable air vents Air intake 141 At least one air vent must be open while the cooling is on. Direct the flow of air by tilting and swivelling the slats. To close the vent, turn the adjuster wheel towards the smaller W symbol. To open the vent, turn the adjuster wheel towards the bigger W symbol. 9 Warning Do not attach any objects to the slats of the air vents. Risk of damage and injury in case of an accident.
142 Climate control Air conditioning regular operation In order to ensure continuously efficient performance, cooling must be operated for a few minutes once a month, irrespective of the weather and time of year. Operation with cooling is not possible when the outside temperature is too low.
Driving and operating Driving and operating Driving hints Control of the vehicle Driving hints ............................... 143 Starting and operating ............... 144 Engine exhaust .......................... 148 Automatic transmission .............. 150 Manual transmission .................. 153 Brakes ........................................ 154 Ride control systems ................. 156 Driver assistance systems ......... 159 Fuel ............................................ 167 Towing ........
144 Driving and operating Starting and operating Ignition switch positions New vehicle running-in Do not brake unnecessarily hard for the first few journeys. During the first drive, smoke may occur because of wax and oil evaporating off the exhaust system. Park the vehicle in the open for a while after the first drive and avoid inhaling the fumes. During the running-in period fuel and engine oil consumption may be higher and the cleaning process of the diesel particle filter may take place more often.
Driving and operating Do not operate the accelerator pedal. Diesel engine: turn the key to position 2 for preheating until control indicator ! goes out. Turn the key briefly to position 3 and release: an automatic procedure operates the starter with a short delay as long as the engine is running, see Automatic Starter Control. Before restarting or to switch off the engine, turn the key back to position 0. During an Autostop, the engine can be started by depressing the clutch pedal.
146 Driving and operating Stop-start system Deactivation The stop-start system helps to save fuel and to reduce the exhaust emissions. When conditions allow, it switches off the engine as soon as the vehicle is at a low speed or at a standstill, e.g. at a traffic light or in a traffic jam. It starts the engine automatically as soon as the clutch is depressed. A battery sensor ensures that an Autostop is only performed if the battery is sufficiently charged for a restart.
Driving and operating ■ The stop-start system is not manually deactivated ■ the bonnet is fully closed ■ the driver's door is closed or the driver's seat belt is fastened ■ the battery is sufficiently charged and in good condition ■ the engine is warmed up ■ the engine coolant temperature is not too high ■ the engine exhaust temperature is not too high, e.g.
148 Driving and operating ■ the vehicle starts to move ■ the climate control system requests an engine start ■ the air conditioning is manually switched on If the bonnet is not fully closed, a warning message is displayed in the Driver Information Centre. If an electrical accessory, e.g. a portable CD player, is connected to the power outlet, a brief power drop during restart might be noticeable. Parking ■ Do not park the vehicle on an easily ignitable surface.
Driving and operating take up to 25 minutes. Typically it needs between 7 and 12 minutes. Autostop is not available and fuel consumption may be higher during this period. The emission of smells and smoke during this process is normal. full continue driving or warning code 55 appears in the Driver Information Centre. % illuminates when diesel particle filter is full. Start cleaning process as soon as possible. % flashes when diesel particle filter has reached the maximum filling level.
150 Driving and operating rectified by a workshop as soon as possible. In an emergency, driving can be continued for a short period, keeping vehicle speed and engine speed low. Automatic transmission Selector lever The automatic transmission permits automatic gearshifting (automatic mode) or manual gearshifting (manual mode). Transmission display The mode or selected gear is shown in the transmission display.
Driving and operating Do not accelerate while engaging a gear. Never depress the accelerator pedal and brake pedal at the same time. When a gear is engaged, the vehicle slowly begins to creep when the brake is released. 151 Manual mode Engine braking To utilise the engine braking effect, select a lower gear in good time when driving downhill, see manual mode. Without brake pedal applied, the control indicator j illuminates.
152 Driving and operating In manual mode no automatic shifting to a higher gear takes place at high engine revolutions. Electronic driving programmes ■ Following a cold start, the operating temperature programme increases engine speed to quickly bring the catalytic converter to the required temperature. ■ The automatic neutral shift function automatically shifts to idling when the vehicle is stopped with a forward gear engaged and the brake pedal is pressed.
Driving and operating 2. Release the selector lever trim from the centre console at the front, fold it upwards and rotate it to the left. 3. Insert a screwdriver into the opening as far as it will go and move the selector lever out of P or N. If P or N is engaged again, the selector lever will be locked in position again. Have the cause of the power supply interruption remedied by a workshop. 4. Mount the selector lever trim onto the centre console and refit.
154 Driving and operating Brakes The brake system comprises two independent brake circuits. If a brake circuit fails, the vehicle can still be braked using the other brake circuit. However, braking effect is achieved only when the brake pedal is depressed firmly. Considerably more force is needed for this. The braking distance is extended. Seek the assistance of a workshop before continuing your journey.
Driving and operating Parking brake Electrical parking brake Manual parking brake 155 Before leaving the vehicle, check the electrical parking brake status. Control indicator m 3 104. Releasing Switch on ignition. Keep brake pedal depressed and then push switch m. Always apply parking brake firmly without operating the release button, and apply as firmly as possible on a downhill or uphill slope.
156 Driving and operating As soon as the switch m is released, dynamic braking will be stopped. Fault Failure mode of electrical parking brake is indicated by control indicator j and by a code number or a vehicle message which is displayed in the Driver Information Centre. Vehicle messages 3 113. Apply electrical parking brake: pull and hold the switch m for more than 5 seconds. If control indicator m illuminates, electrical parking brake is applied.
Driving and operating 9 Warning Do not let this special safety feature tempt you into taking risks when driving. Adapt speed to the road conditions. Control indicator b 3 106. Deactivation TC can be switched off when spinning of drive wheels is required: press button b briefly. Control indicator k illuminates. TC is reactivated by pressing the b button again. TC is also reactivated the next time the ignition is switched on.
158 Driving and operating ESC is reactivated by pressing the b button again. If the TC system was previously disabled, both TC and ESC are reactivated. ESC is also reactivated the next time the ignition is switched on. Interactive driving system Flex Ride Flex Ride driving system allows the driver to select between three driving modes: ■ SPORT mode: press button SPORT, LED illuminates. ■ TOUR mode: press button TOUR, LED illuminates.
Driving and operating ■ Shift points of automatic transmission occur in a comfort mode. ■ Illumination of main instruments is white. Normal mode All settings of the systems are adapted to standard values. Drive mode control Within each manual selected driving mode SPORT, TOUR or Normal, the Drive Mode Control (DMC) detects and analyses continuously the real driving characteristic, responses by the driver, and the active dynamic state of the vehicle.
160 Driving and operating Do not use the cruise control if it is not advisable to maintain a constant speed. With automatic transmission, only activate cruise control in automatic mode. Control indicator m 3 108. Switching on Press rocker switch m at the upper end, control indicator m illuminates white. Activation Accelerate to the desired speed and turn thumb wheel to SET/-, the current speed is stored and maintained. Control indicator m illuminates green. Accelerator pedal can be released.
Driving and operating Parking assist parking assist the system consists of four additional ultrasonic parking sensors in the front bumper. The system uses two different frequencies for the front and rear sensors, respectively, each with a different sound. Control indicator r 3 106. Activation The parking assist makes parking easier by measuring the distance between the vehicle and obstacles, and giving acoustic signals.
162 Driving and operating Fault In the event of a fault in the system, r illuminates or a vehicle message is displayed in the Driver Information Centre. Additionally, r illuminates or a vehicle message is displayed in the Driver Information Centre if a malfunction of the system due to temporary conditions like snow covered sensors is detected. Vehicle messages 3 113.
Driving and operating Display indication ■ end of speed limit ■ end of no passing Speed limit signs are displayed in the Driver Information Centre until the next speed limit sign or end of speed limit is detected. No passing signs have priority above speed limits. Combinations of both signs in the display are possible. 163 An exclamation mark in a frame indicates that there is an supplementary sign detected which cannot be recognised by the system.
164 Driving and operating Pop-up function If the system is deactivated, the content of the traffic sign page is cleared, indicated by the following symbol: Speed limits and no passing signs are displayed as pop-up on each page of the menu. The content of the traffic sign page is also cleared during driving by pushing the SET/CLR button on the turn signal lever. The pop-up function can be deactivated on the traffic sign page by pressing the SET/CLR button on the turn signal lever.
Driving and operating Fault Once setting page is displayed, select Off to deactivate pop-up function. Reactivate by selecting On. When switching on the ignition, pop-up function is deactivated. Pop-up indication is displayed for approx. 8 seconds in the Driver Information Centre.
166 Driving and operating changes and warns the driver in the event of an unintended lane change via visual and acoustic signals. Criteria for the detection of an unintended lane change are: ■ no operation of turn signals ■ no brake pedal operation ■ no active accelerator operation or speeding-up ■ no active steering If the driver is active, no warning will be issued. Activation The lane departure warning system is activated by pressing the ) button.
Driving and operating Fuel Fuel for petrol engines Only use unleaded fuel that complies with EN 228. Usage of fuel with quality, not complying to the Technical Regulations in effect (Decree № 118 of 27.02.2008 with amendments of 30.12.2008 № 1076) can lead to engine damage and loss of all warranty obligations. Equivalent standardised fuels with an ethanol content of max. 10 % by volume may be used. In this case only use fuel that complies with E DIN 51626-1.
168 Driving and operating The fuel filler cap can be retained in the bracket on the fuel filler flap. 9 Danger Before refuelling, switch off engine and any external heaters with combustion chambers. Switch off any mobile phones. Follow the operating and safety instructions of the filling station when refuelling. 9 Danger Fuel is flammable and explosive. No smoking. No naked flames or sparks. If you can smell fuel in your vehicle, have the cause of this remedied immediately by an authorized dealer.
Driving and operating The determination of fuel consumption is regulated by directive R (EC) No. 715/2007 (in the newest version respectively). The specification of CO2 emission is also a constituent of the directive. The figures given must not be taken as a guarantee for the actual fuel consumption of a particular vehicle. Furthermore, fuel consumption is dependent on personal driving style as well as road and traffic conditions. All values are based on the EU base model with standard equipment.
170 Driving and operating The permissible trailer loads are specified in the vehicle documents. In general, they are valid for gradients up to max. 12 %. The permitted trailer load applies up to the specified incline and up to an altitude of 1000 metres above sea level. Since engine power decreases as altitude increases due to the air becoming thinner, therefore reducing climbing ability, the permissible gross train weight also decreases by 10 % for every 1000 metres of additional altitude.
Driving and operating Fitting the coupling ball bar Disengage and fold down the socket. Remove the sealing plug from the opening for the coupling ball bar and stow it. Otherwise, the coupling ball bar must be tensioned before being inserted: ■ Unlock coupling ball bar by turning key to position c. Checking the tensioning of the coupling ball bar Press fastenings inward and remove cover. ■ Pull out rotary knob and turn clockwise as far as it will go.
172 Driving and operating Inserting the coupling ball bar Eye for break-away stopping cable ■ The coupling ball bar must be firmly engaged in the opening. ■ The coupling ball bar must be locked and the key removed. 9 Warning Towing a trailer is permitted only when a coupling ball bar is fitted correctly. If the coupling ball bar does not engage correctly, seek the assistance of a workshop. Insert the tensioned coupling ball bar in the opening and push firmly upwards until it audibly engages.
Driving and operating Open the protective flap and turn the key to position c to unlock the coupling ball bar. Pull out rotary handle and turn clockwise as far as it will go. Pull out coupling ball bar downwards. Insert sealing plug in opening. Fold away socket. Replace cover. Trailer stability assist If the system detects snaking movements, engine power is reduced and the vehicle/trailer combination is selectively braked until the snaking ceases.
174 Vehicle care Vehicle care General Information ................... 174 Vehicle checks ........................... 175 Bulb replacement ....................... 182 Electrical system ........................ 191 Vehicle tools .............................. 197 Wheels and tyres ....................... 198 Jump starting ............................. 211 Towing ....................................... 212 Appearance care .......................
Vehicle care ■ Disconnect the clamp from the negative terminal of the vehicle battery. Beware that all systems are not functional, e.g. anti-theft alarm system. Vehicle checks Performing work Putting back into operation When the vehicle is to be put back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery. Activate the electronics of the power windows. ■ Check tyre pressure. ■ Fill up the washer fluid reservoir. ■ Check the engine oil level. ■ Check the coolant level.
176 Vehicle care If the bonnet is opened during an Autostop, the engine will be restarted automatically for safety reasons. Closing Before closing the bonnet, press the support into the holder. Lower the bonnet and allow it to drop into the catch. Check that the bonnet is engaged. Push the safety catch to the right and open the bonnet. Secure the bonnet support. Caution It is the owner's responsibility to maintain the proper level of an appropriate quality oil in the engine.
Vehicle care We recommend the use of the same grade of engine oil that was used at last change. The engine oil level must not exceed the MAX mark on the dipstick. Caution 177 Coolant level Caution Too low a coolant level can cause engine damage. Overfilled engine oil must be drained or suctioned out. When the engine oil level has dropped to the MIN mark, top up engine oil. Capacities 3 236. Fit the cap on straight and tighten it. Engine coolant The coolant provides freeze protection down to approx.
178 Vehicle care 9 Warning Washer fluid In the event of minimum thickness of the brake lining, a squealing noise sounds during braking. Continued driving is possible but have the brake lining replaced as soon as possible. Once new brake linings are installed, do not brake unnecessarily hard for the first few journeys. Allow the engine to cool before opening the cap. Carefully open the cap, relieving the pressure slowly.
Vehicle care Battery The vehicle battery is maintenancefree provided that the driving profile allows sufficient charging of the battery. Short-distance-driving and frequent engine starts can discharge the battery. Avoid the use of unnecessary electrical consumers. The brake fluid level must be between the MIN and MAX marks. When topping up, ensure maximum cleanliness as contamination of the brake fluid can lead to brake system malfunctions. Have the cause of the loss of brake fluid remedied by a workshop.
180 Vehicle care Charging the battery 9 Warning On vehicles with stop-start system, ensure that the charging potential does not exceed 14.6 volts when using a battery charger. Otherwise the battery might be damaged. Jump starting 3 211. An AGM battery can be identified by the label on the battery. We recommend the use of an original Vauxhall battery. Note Using an AGM battery different from the original Vauxhall battery might result in a lower performance of the stop-start system.
Vehicle care Diesel fuel system bleeding If the tank has been run dry, the diesel fuel system must be bled. Switch on the ignition three times for 15 seconds at a time. Then start the engine for a maximum of 40 seconds. Repeat this process after no less than 5 seconds. If the engine fails to start, seek the assistance of a workshop. Lift the wiper arm until it stays in the raised position, press button to disengage the wiper blade and remove.
182 Vehicle care Bulb replacement Switch off the ignition and switch off the relevant switch or close the doors. Only hold a new bulb at the base! Do not touch the bulb glass with bare hands. Use only the same bulb type for replacement. Replace headlight bulbs from within the engine compartment. Headlights have separate systems for low beam 1 (outer bulbs) and high beam 2 (inner bulbs). Low beam 2. Rotate the bulb holder anticlockwise to disengage. Withdraw the bulb holder from the reflector.
Vehicle care 3. Detach the bulb from the bulb holder and replace the bulb. 4. Insert the bulb holder, engaging the two lugs into the reflector and rotate clockwise to secure. 5. Fit the cap and rotate clockwise. High beam 183 3. Detach the bulb from the bulb holder and replace the bulb. 4. Insert the bulb holder, engaging the two lugs into the reflector and rotate clockwise to secure. 5. Fit the cap and rotate clockwise. Sidelights/Daytime running light 2.
184 Vehicle care 3. Remove the bulb from the socket and replace the bulb. 4. Insert the bulb holder into the reflector. Fit the cap and rotate clockwise. 3. Disengage the bulb holder from the plug connector by pressing the retaining lug. 4. Remove and replace the bulb holder with bulb. 5. Attach the plug connector. 6. Insert the bulb holder into the reflector. 7. Swivel the spring clip forwards and engage. Front turn signal 1. Disengage the spring clip and then swivel it backwards. 2.
Vehicle care Fog lights The bulbs are accessible from beneath the vehicle. 1. Turn the bulb holder anticlockwise and remove it from the reflector. 2. Disengage the bulb holder from the plug connector by pressing the retaining lug. 3. Remove and replace the bulb holder with bulb. 4. Attach the plug connector. 5. Insert the bulb holder into the reflector. 6. Turn the bulb holder clockwise and engage. 185 Tail lights Saloon/Hatchback 1. Release the cover and remove it.
186 Vehicle care 2. Unscrew the plastic securing nut from the inside by hand. 3. Carefully withdraw the light assembly from retaining pins and remove. Make sure that the cable duct remains in position. 4. Detach the cable from the retainer. 5. Detach the wiring plug from the bulb carrier. 6. Unscrew the three screws with a coin and remove the bulb carrier. 7. Remove and replace the bulb. Tail lights (1) Brake light (2) Turn signal light (3) 8.
Vehicle care Sports tourer 1. Open the tailgate and remove the three covers. 2. Unscrew the three screws and remove. 3. Remove the tail light assembly. Make sure that the cable duct remains in position. 4. Press the retaining lug and remove the bulb carrier from the tail light assembly. 187 5. To replace the tail light (1), remove and replace the bulb To replace the rear fog light (2), push the bulb slightly into the socket, rotate anticlockwise, remove and replace the bulb. 6.
188 Vehicle care 2. Remove cover. 4. Carefully remove tail light assembly. Take care that the cable duct remains in position. Detach wiring plug from bulb holder. When assembling press the blind into the rubber grommets to reach full retention force. 7. Switch on the ignition, operate and check all lights. 3. Unscrew two plastic securing nuts from the inside by hand. 5. Remove and replace the bulb. Tail lights (1 + 2) Turn signal light (3) Brake light (4) 6.
Vehicle care Tail light in the tailgate 1. Open the tailgate and remove the covers. 2. Unscrew the screws and remove. 3. Remove the tail light assembly. 189 Rear fog light / reverse light in the tailgate 4. Remove and replace the bulb. 5. Install the tail light assembly in the tailgate and tighten the screws. Attach the covers. 6. Switch on the ignition, operate and check all lights. 1. Remove cover.
190 Vehicle care 2. Remove and replace the bulb of rear fog light. 3. Close cover. For replacing reverse light bulb on the right side of the tailgate, proceed in the same way. 2. Remove the bulb holder downwards, taking care not to pull on the cable. Courtesy light, reading lights Have bulbs replaced by a workshop. Load compartment light Have bulbs replaced by a workshop. Side turn signal lights Instrument panel illumination Have bulbs replaced by a workshop.
Vehicle care Electrical system Fuses Data on the replacement fuse must match the data on the defective fuse. There are three fuse boxes in the vehicle: ■ in the front left of the engine compartment, ■ in left-hand drive vehicles, in the interior behind the storage compartment, or, in right-hand drive vehicles, behind the glovebox, ■ behind a cover on the left side of the load compartment. Before replacing a fuse, turn off the respective switch and the ignition.
192 Vehicle care Engine compartment fuse box Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse. The fuse box is in the front left of the engine compartment. Disengage the cover, lift it upwards and remove.
Vehicle care No. Circuit No. Circuit No.
194 Vehicle care No. Circuit Instrument panel fuse box 50 Headlamp levelling 51 Air shutter 52 Auxiliary heater, diesel engine 53 Transmission control module, Engine control module 54 Wiring monitoring After having changed defective fuses close the fuse box cover and press until it engages. If the fuse box cover is not closed correctly, malfunction may occur. In right-hand drive vehicles, the fuse box is located behind a cover in the glovebox. Open the glovebox, then open the cover and fold it down.
Vehicle care No. Circuit No.
196 Vehicle care Fuse assignments Fold down the blind and remove. No. Circuit 1 Trailer module 2 Trailer outlet 3 Parking assist 4 – 5 – 6 – 7 – 8 Anti-theft alarm system 9 – 10 – 11 Trailer module, Trailer socket 12 – 13 Trailer outlet 14 – 15 – Remove the cover.
Vehicle care No. Circuit Vehicle tools 18 – Tools 19 Steering wheel heating 197 Vehicles with tyre repair kit 20 Sunroof 21 Seat heating 22 – 23 – 24 – 25 – 26 – When assembling press the blind into the rubber grommets to reach full retention force. 27 – 28 – 29 – 30 – 31 Amplifier, Subwoofer 32 Active damping system, Lane departure warning The tools and tyre repair kit are in a storage compartment below the floor cover in the load compartment.
198 Vehicle care Vehicles with spare wheel, variant 1 The jack, the tools and a strap for securing a damaged wheel are in a storage compartment below the spare wheel in the load compartment. Spare wheel 3 208. Vehicles with spare wheel, variant 2 The jack and the tools are in a storage compartment below the spare wheel in the load compartment. The wheel wrench and the extension bar for securing a damaged wheel are in a tool bag located in the spare wheel well. Spare wheel 3 208.
Vehicle care Speed code letter: Q = up to 100 mph S = up to 112 mph T = up to 118 mph H = up to 130 mph V = up to 150 mph W = up to 168 mph Tyre pressure Check the pressure of cold tyres at least every 14 days and before any long journey. Do not forget the spare wheel. This also applies to vehicles with tyre pressure monitoring system. Unscrew the valve cap. Tyre pressure 3 237 and on the label on the front left door frame. The tyre pressure data refers to cold tyres.
200 Vehicle care Press the MENU button to select the Vehicle Information Menu. Turn the adjuster wheel to select the tyre pressure monitoring system. System status and small pressure differences are displayed by a warning message with the corresponding tyre flashing in the Driver Information Centre. Furthermore considerable pressure differences between the tyres on one axle are displayed by a warning message in the Driver Information Centre.
Vehicle care Changing tyre and wheel size If problems occur during the relearn process a warning message is displayed in the Driver Information Centre. If tyres of a different size than those fitted at the factory are used, it may be necessary to reprogramme the speedometer as well as the nominal tyre pressure and make other vehicle modifications. After converting to a different tyre size, have the label with tyre pressures replaced.
202 Vehicle care If the wheel covers and tyres used are not factory approved, the tyres must not have a rim protection ridge. Wheel covers must not impair brake cooling. 9 Warning Use of unsuitable tyres or wheel covers could lead to sudden pressure loss and thereby accidents. Tyre chains Tyre chains are only permitted on the front wheels. Always use fine mesh chains that add no more than 10 mm to the tyre tread and the inboard sides (including chain lock). 9 Warning Damage may lead to tyre blowout.
Vehicle care 203 The tyre repair kit is in a compartment under the floor cover in the load compartment or in the underseat storage compartment 3 55. 1. Take the tyre repair kit from the compartment. 2. Remove the compressor. 3. Remove the electrical connection cable and air hose from the stowage compartments on the underside of the compressor. 4. Screw the compressor air hose to the connection on the sealant bottle. 5. Fit the sealant bottle into the retainer on the compressor.
204 Vehicle care 10. Set the rocker switch on the compressor to I. The tyre is filled with sealant. 11. The compressor pressure gauge briefly indicates up to 6 bar whilst the sealant bottle is emptying (approx. 30 seconds). Then the pressure starts to drop. 12. All of the sealant is pumped into the tyre. Then the tyre is inflated. 13. The prescribed tyre pressure should be obtained within 10 minutes. Tyre pressure 3 237. When the correct pressure is obtained, switch off the compressor.
Vehicle care If tyre pressure is more than 1.3 bar, set it to the correct value. Repeat the procedure until there is no more loss of pressure. If the tyre pressure has fallen below 1.3 bar, the vehicle must not be used. Seek the assistance of a workshop. 18. Stow away tyre repair kit in load compartment. Note The driving characteristics of the repaired tyre are severely affected, therefore have this tyre replaced.
206 Vehicle care ■ Clean wheel nuts and thread with a clean cloth before mounting the wheel. place a soft cloth between the screwdriver and the alloy wheel. 2. Variant 1: 9 Warning Do not grease wheel bolt, wheel nut and wheel nut cone. Install the wheel wrench ensuring that it locates securely and loosen each wheel nut by half a turn. Variant 2: 1. Disengage wheel nut caps with a screwdriver and remove. Pull off the wheel cover with the hook. Vehicle tools 3 197.
Vehicle care 207 3. Ensure the jack is correctly positioned under the relevant vehicle jacking point. 4. Variant 1: Set the jack to the necessary height. Position it directly below the jacking point in a manner that prevents it from slipping. Attach jack handle and with the jack correctly aligned rotate handle until wheel is clear of the ground. Variant 2: Set the jack to the necessary height. Position it directly below the jacking point in a manner that prevents it from slipping.
208 Vehicle care Attach wheel wrench and with the jack correctly aligned rotate wheel wrench until wheel is clear of the ground. 5. Unscrew the wheel nuts. 6. Change the wheel. 7. Screw on the wheel nuts. 8. Lower vehicle. 9. Install the wheel wrench ensuring that it locates securely and tighten each nut in a crosswise sequence. Tightening torque is 140 Nm. 10. Align the valve hole in the wheel cover with the tyre valve before installing. Install wheel nut caps. 11.
Vehicle care The use of a spare wheel that is smaller than the other wheels or in combination with winter tyres could affect driveability. Have the defective tyre replaced as soon as possible. The spare wheel is located in the load compartment beneath the floor covering. It is secured with a wing nut. The spare wheel well is not designed for all permissible tyre sizes.
210 Vehicle care Replace the long bolt before fitting the spare wheel in the well after renewing or repairing the defective wheel. 9 Warning ■ Install the hexagon key of the wheel wrench ensuring that it locates securely on the bolt. ■ Turn the wheel wrench anticlockwise to loosen the bolt. Remove the bolt. ■ Take the long bolt from the tool box and screw it in hand-tight using the wheel wrench. ■ Store the tool box and the damaged wheel and secure it by turning the wing nut clockwise.
Vehicle care Jump starting Do not start with quick charger. A vehicle with a discharged battery can be started using jump leads and the battery of another vehicle. 9 Warning Be extremely careful when starting with jump leads. Any deviation from the following instructions can lead to injuries or damage caused by battery explosion or damage to the electrical systems of both vehicles. 9 Warning Avoid contact of the battery with eyes, skin, fabrics and painted surfaces.
212 Vehicle care 3. Connect the black lead to the negative terminal of the booster battery. 4. Connect the other end of the black lead to a vehicle grounding point, such as the engine block or an engine mounting bolt. Connect as far away from the discharged battery as possible, however at least 60 cm. Route the leads so that they cannot catch on rotating parts in the engine compartment. To start the engine: 1. Start the engine of the vehicle providing the jump. 2. After 5 minutes, start the other engine.
Vehicle care Caution 213 Towing another vehicle Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. Screw in the towing eye as far as it will go until it stops in a horizontal position. Attach a tow rope – or better still a tow rod – to the towing eye. The towing eye must only be used for towing and not for recovering the vehicle. Switch on ignition to release steering wheel lock and to permit operation of brake lights, horn and windscreen wiper. Transmission in neutral.
214 Vehicle care Caution Drive slowly. Do not drive jerkily. Excessive tractive force can damage the vehicle. After towing, unscrew the towing eye. Insert cap at the bottom and engage. Screw in the towing eye as far as it will go until it stops in a horizontal position. The lashing eye at the rear underneath the vehicle must never be used as a towing eye. Attach a tow rope – or even better a tow bar – to the towing eye. The towing eye must only be used for towing and not for recovering a vehicle.
Vehicle care If using a vehicle wash, comply with the vehicle wash manufacturer's instructions. The windscreen wiper and rear window wiper must be switched off. Remove antenna and external accessories such as roof racks etc. If you wash your vehicle by hand, make sure that the insides of the wheel housings are also thoroughly rinsed out. Clean edges and folds on opened doors and the bonnet as well as the areas they cover. Have the door hinges of all doors greased by a workshop.
216 Vehicle care Paintwork damage Rectify minor paintwork damage with a touch-up pen before rust forms. Have more extensive damage or rust areas repaired by a workshop. Underbody Some areas of the vehicle underbody have a PVC undercoating while other critical areas have a durable protective wax coating. After the underbody is washed, check the underbody and have it waxed if necessary. Bitumen/rubber materials could damage the PVC coating. Have underbody work carried out by a workshop.
Service and maintenance Service and maintenance General information ................... 217 Recommended fluids, lubricants and parts .................................... 218 General information Service information In order to ensure economical and safe vehicle operation and to maintain the value of your vehicle, it is of vital importance that all maintenance work is carried out at the proper intervals as specified. The detailed, up-to-date service schedule for your vehicle is available at the workshop.
218 Service and maintenance Make sure that the Service and Warranty Booklet is completed correctly as continuous proof of service is essential if any warranty or goodwill claims are to be met, and is also a benefit when selling the vehicle. Service interval with remaining engine oil life duration The service interval is based on several parameters depending on usage. The service display lets you know when to change the engine oil. Service display 3 100.
Service and maintenance Select the appropriate engine oil based on its quality and on the minimum ambient temperature 3 222. Additional engine oil additives The use of additional engine oil additives could cause damage and invalidate the warranty. Engine oil viscosity grades The SAE viscosity grade gives information of the thickness of the oil. Multigrade oil is indicated by two figures, e.g. SAE 5W-30.
220 Technical data Technical data Vehicle identification .................. 220 Vehicle data ............................... 222 Vehicle identification Identification plate Vehicle Identification Number The identification plate is located on the front left door frame. The Vehicle Identification Number is visible through the windscreen.
Technical data Information on identification label: 1 = Manufacturer 2 = Type approval number 3 = Vehicle Identification Number 4 = Permissible gross vehicle weight rating in kg 5 = Permissible gross train weight in kg 6 = Maximum permissible front axle load in kg 7 = Maximum permissible rear axle load in kg 8 = Vehicle-specific or countryspecific data Identification plate for Russia: 1 2 3 4 5 6 7 = = = = = = = 8 = 9 = 10 = 11 = 12 = 13 = Type approval number Manufacturer Model name Vehicle Identif
222 Technical data Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries (except Belarus, Moldova, Russia, Serbia, Turkey) Engine oil quality Only Israel Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (including CNG, LPG, E85) Diesel engines dexos 1 – – ✔ – dexos 2 ✔ ✔ – ✔ In case dexos quality is unavailable you may use max. 1 litre engine oil quality ACEA C3 once between each oil change.
Technical data 223 International service schedule Required engine oil quality All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines (including CNG, LPG, E85) Diesel engines Petrol engines (including CNG, LPG, E85) Diesel engines dexos 1 ✔ – – – dexos 2 – ✔ ✔ ✔ In case dexos quality is unavailable you may use the oil qualities listed below: All countries outside Europe except Israel Engine oil quality Only Belarus, Moldov
224 Technical data All countries outside Europe except Israel Engine oil quality Only Belarus, Moldova, Russia, Serbia, Turkey Petrol engines Diesel engines Petrol engines (including CNG, LPG, E85) (including CNG, LPG, E85) Diesel engines ACEA A3/B3 ✔ – ✔ – ACEA A3/B4 ✔ ✔ ✔ ✔ ACEA C3 ✔ ✔ ✔ ✔ API SM ✔ – ✔ – API SN resource conserving ✔ – ✔ – Engine oil viscosity grades All countries outside Europe (except Israel), including Belarus, Moldova, Russia, Serbia, Turkey Ambient tempe
Technical data 225 Engine data Sales designation 1.4 1.4 1.4 1.4 1.6 1.
226 Technical data Sales designation 1.3 1.7 1.7 1.7 1.7 Engine identifier code A13DTE A17DTE A17DTC A17DTF A17DTS Number of cylinders 4 4 4 4 4 1248 1686 1686 1686 1686 Engine power [kW] 70 81 81 96 96 at rpm 4000 4000 4000 4000 4000 Torque [Nm] 190 280 280 300 300 at rpm 1750-3250 1750-2500 1750-2500 2000-2500 2000-2500 Fuel type Diesel Diesel Diesel Diesel Diesel Oil consumption [l/1000 km] 0.6 0.6 0.6 0.6 0.
Technical data Sales designation 1.7 1.7 2.0 Turbo Engine identifier code A17DTJ A17DTR A20DTH at rpm 1700-2550 2000-2700 1750-2500 Fuel type Diesel Diesel Diesel Oil consumption [l/1000 km] 0.6 0.6 0.
228 Technical data Engine A13DTE A17DTE A17DTC A17DTF A17DTS Manual transmission 109 4) 4) 4) 4) Automatic transmission – – – – – Maximum speed2) [mph] Engine A17DTJ A17DTR A20DTH Manual transmission 113 122 134 Automatic transmission – – 131 Maximum speed2) [mph] Sports tourer Engine A14XER A14NEL A14NET A16LET A16XER Manual transmission 109 119 125 138 116 Automatic transmission – – 124 131 113 Maximum speed 2) 4) 5) [mph]5) The maximum speed indi
Technical data Engine A13DTE A17DTJ A17DTR A20DTH Manual transmission 108 113 120 133 Automatic transmission – – – 129 Maximum speed 229 2)[mph] Vehicle weight Kerb weight, basic model without any optional equipment 5-door hatchback Engine Manual transmission Automatic transmission without/with air conditioning [kg] A14XEL 1373/1388 – A14XER 1373/1388 – A14NEL 1393/1408 – A14NET 1393/1408 –/1453 A16LET –/1490 –/1503 A16XER 1393/1408 –/1443 A13DTE 1393/1408 – A17DT
230 Technical data 5-door hatchback Engine Manual transmission Automatic transmission without/with air conditioning [kg] A17DTE 1503/1518 – A17DTF 1503/1518 – A17DTJ 1503/1518 – A17DTR 1503/1518 – A17DTS 1503/1518 – A20DTH 1503/1518 –/1590 A20DTH6) 1503/1518 – 6) With stop-start function.
Technical data Kerb weight, basic model with all optional equipment 5-door hatchback Engine Manual transmission Automatic transmission without/with air conditioning [kg] A14XEL –/1545 – A14XER –/1545 – A14NEL –/1611 – A14NET –/1611 –/1613 A16LET –/1613 –/1665 A16XER –/1578 –/1613 A13DTE –/1571 – A17DTC –/1664 – 231
232 Technical data 5-door hatchback Engine Manual transmission Automatic transmission without/with air conditioning [kg] A17DTE –/1664 – A17DTF –/1664 – A17DTJ –/1684 – A17DTR –/1689 – A17 DTS –/1664 A20DTH –/1711 –/1731 A20DTH6) –/1701 – 6) With stop-start function.
Technical data Kerb weight, basic model without any optional equipment Sports tourer Engine Manual transmission Automatic transmission without/with air conditioning [kg] A14XER 1393/1408 – A14NEL 1471/1486 –/1503 A14NET 1437/1452 –/1503 A16LET –/1503 –/1550 A16XER 1437/1452 –/1503 A13DTE 1471/1486 – A17DTJ 1503/1518 – A17DTR 1503/1518 – A20DTH 1550/1565 –/1613 A20DTH6) 1571/1586 – 6) With stop-start function.
234 Technical data Kerb weight, basic model with all optional equipment Sports tourer Engine Manual transmission Automatic transmission without/with air conditioning [kg] A14XER –/1571 – A14NEL –/1664 –/1664 A14NET –/1664 –/1664 A16LET –/1664 –/1701 A16XER –/1613 –/1664 A13DTE –/1664 – A17DTJ –/1733 – A17DTR –/1733 – A20DTH –/1733 –/1733 A20DTH6) –/1733 – 6) With stop-start function.
Technical data Vehicle dimensions 5-door hatchback Sports tourer Length [mm] 4419 4698 Width without exterior mirrors [mm] 1814 1814 Width with two exterior mirrors [mm] 2013 2013 Height (without antenna) [mm] 1510 1535 Length of load compartment floor [mm] 836 1069 Length of load compartment with folded rear seats [mm] 1549 1835 Load compartment width [mm] 1027 1026 Load compartment height [mm] 554 721 Wheelbase [mm] 2685 2685 Turning circle diameter [m] 11.5 11.
236 Technical data Capacities Engine oil Engine A14XEL, A14XER A14NEL, A14NET A16LET, A16XER A13DTE ecoFlex including Filter [l] 4.0 4.0 4.5 3.2 between MIN and MAX [l] 1.0 1.0 1.0 1.0 Engine A17DTE, A17DTC A17DTF, A17DTS A17DTJ, A17DTR A20DTH including Filter [l] 4.0 4.0 5.4 4.5 between MIN and MAX [l] 1.0 1.0 1.0 1.0 Fuel tank Petrol/diesel, nominal capacity [l] 7) A13 DTE diesel engine with stop-start system reduced capacity: 46 litres.
Technical data 237 Tyre pressures Engine Tyres A14XER, 205/55 R16, A14XEL 205/60 R16, Comfort with up to 3 people ECO with up to 3 people With full load front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 220/2.2 (32) 220/2.2 (32) 270/2.7 (39) 270/2.7 (39) 230/2.3 (33) 270/2.
238 Engine Technical data Tyres A16LET 205/65 R16, 9)8) 215/60 Comfort with up to 3 people ECO with up to 3 people With full load front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 230/2.3 (33) 230/2.3 (33) 270/2.7 (39) 270/2.7 (39) 240/2.4 (35) 280/2.8 (41) R16,8) 225/50 R17,8) 235/45 R18 235/40 R19 240/2.4 (35) 220/2.2 (32) – – 250/2.5 (36) 290/2.9 (42) 205/60 R16, 9) 250/2.5 (36) 230/2.
Technical data Engine Tyres A17DTE, 205/65 R16, 9)10) A17DTC, 215/60 R16, 10) A17DTF, 225/50 R17, 10) A17DTS 235/45 R18 205/55 R16, Comfort with up to 3 people ECO with up to 3 people With full load front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 239 230/2.3 (33) 230/2.3 (33) 270/2.7 (39) 270/2.7 (39) 240/2.4 (35) 280/2.8 (41) 240/2.4 (35) 220/2.2 (32) – – 250/2.5 (36) 290/2.9 (42) 250/2.
240 Engine Technical data Tyres A17DTJ 205/65 R16, 9)8) 215/60 R16, Comfort with up to 3 people ECO with up to 3 people With full load front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 230/2.3 (33) 230/2.3 (33) 270/2.7 (39) 270/2.7 (39) 240/2.4 (35) 280/2.8 (41) 10) 225/50 R17, 8) 235/45 R18 205/55 R16, 240/2.4 (35) 220/2.2 (32) – – 250/2.5 (36) 290/2.9 (42) 250/2.5 (36) 230/2.
Technical data Engine Tyres A17DTR 205/65 R16, 9)8) 215/60 R16, Comfort with up to 3 people ECO with up to 3 people With full load front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 241 230/2.3 (33) 230/2.3 (33) 270/2.7 (39) 270/2.7 (39) 240/2.4 (35) 280/2.8 (41) 8) 225/50 R17, 235/45 R18 205/55 R16, 240/2.4 (35) 220/2.2 (32) – – 250/2.5 (36) 290/2.9 (42) 250/2.5 (36) 230/2.3 (33) – – 260/2.
242 Engine Technical data Tyres A20DTH 205/65 R16, 9)8) Comfort with up to 3 people ECO with up to 3 people With full load front rear front rear front rear [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) [kPa/bar] ([psi]) 230/2.3 (33) 230/2.3 (33) 270/2.7 (39) 270/2.7 (39) 240/2.4 (35) 280/2.8 (41) 215/60 R16, 225/50 R17, 235/45 R18 235/40 R19 240/2.4 (35) 220/2.2 (32) – – 250/2.5 (36) 290/2.9 (42) 205/60 R16, 9) 250/2.5 (36) 230/2.
Technical data Towing hitch installation dimensions 243
244 Customer information Customer information Vehicle data recording and privacy ....................................... 244 Vehicle data recording and privacy Event data recorders The vehicle has a number of sophisticated systems that monitor and control several vehicle data.
Customer information In addition, the manufacturer may use the collected or received diagnostic data: ■ for the manufacturer's research needs ■ to make it available for research needs where appropriate confidentiality is maintained and need is shown ■ to share summary data which is not tied to a specific vehicle with other organisations for research purposes Radio Frequency Identification (RFID) RFID technology is used in some vehicles for functions such as tyre pressure monitoring and ignition system secu
246 Index A Accessories and vehicle modifications .......................... 174 Active head restraints................... 36 Adaptive forward lighting ... 108, 128 Adjustable air vents ................... 141 Airbag and belt tensioners ......... 103 Airbag deactivation .............. 46, 103 Airbag system .............................. 44 Air conditioning regular operation ................................ 142 Air conditioning system .............. 136 Air intake ....................................
247 Climate control ............................. 15 Climate control systems............. 135 Clock............................................. 96 Code........................................... 113 Control indicators........................ 100 Control of the vehicle ................. 143 Controls........................................ 91 Convex shape .............................. 28 Coolant and antifreeze............... 218 Cruise control .................... 108, 159 Cupholders .......................
248 Headlights when driving abroad 127 Head restraint adjustment ............. 8 Head restraints ............................ 35 Heated ......................................... 29 Heated rear window ..................... 32 Heated steering wheel ................. 92 Heating ........................................ 40 Heating and ventilation system . 135 Height adjustable rear floor cover 81 High beam ......................... 108, 126 Hill start assist ........................... 156 Horn .................
249 Q Quickheat................................... 140 R Radio Frequency Identification (RFID)..................................... 245 Radio remote control ................... 20 Reading lights ............................ 133 Rear carrier system...................... 57 Rear floor storage cover .............. 81 Rear fog light ............................. 108 Rear fog lights ........................... 131 Rear seats.................................... 40 Rear window wiper/washer ..........
250 U Ultrasonic parking assist ............ 106 Underseat storage ....................... 55 Upshift........................................ 105 Using this manual .......................... 3 V Vehicle checks............................ 175 Vehicle data................................ 222 Vehicle data recording and privacy..................................... 244 Vehicle dimensions .................... 235 Vehicle Identification Number .... 220 Vehicle jack................................
