Operating Instructions

ManualsBrandsVertrax ManualsElectronicsSENSOR

Mopeka Products LLC www.mopeka.com

M2000003A

Manuel & Operating Instructions

Standard Sensor Models M2008 (Propane)

INTENDED USE OF THE M2008 SENSOR IS TO MEASURE THE AMOUNT OF LIQUID PROPANE INSIDE A PROPANE

TANK MEETING THE SPECIFATIONS BELOW, UNDER THE CONDITIONS LISTED BELOW.

THIS DEVICE IS INTENDED FOR OUTDOOR USE ONLY.

WARNING

USE OF THIS DEVICE IN A MANNER OTHER THAN STATED IN THIS MANUAL, MAY RESULT IN IMPAIRMENT OF

THE DESIGNED SAFETY PROTECTION AND THUS AN UNSAFE CONDITION.

SPECIFICATIONS

MEASUREMENT METHOD

Ultrasonic

FLUID

Propane

TANK TYPES

Steel Tanks

Note: Also works with aluminum tanks with alternate mounting.

Not intended for use on composite cylinders.

TANK SIZES

Vertical DOT Cylinders of 20 -100 lb (5 - 25 gal)

Horizontal tanks up to 11’ diameter

Envelope Dimensions

97 x 61 x 17.2 mm (3.8 x 2.4 x 0.68 in)

Mounting location

Tank Bottom

Suitable for these locations

CLASS 1, DIVISION 2, GROUP D

CLASS 1, ZONE 2, GROUP IIA

OPERATING TEMPERATURE RANGE

-40° TO 60°C

TEMPERATURE CODE

BATTERY

2 AA (non replaceable)

HUMIDITY RANGE

0 - 100%

MAX ALTITUDE

4000m

AMBIENT CONDITIONS FOR TESTING

23°C, 14.7 PSIA

WARNING

THIS DEVICE IS NOT TO BE REPAIRED OR OTHERWISE MODIFIED.

MOPEKA PRODUCTS LLC

MAILING ADDRESS: 445 FM 1983, COLORADO CITY, TX 79512

www.mopeka.com

support@mopeka.com

Summary of content (8 pages)

PAGE 1
Manuel & Operating Instructions Standard Sensor Models M2008 (Propane) INTENDED USE OF THE M2008 SENSOR IS TO MEASURE THE AMOUNT OF LIQUID PROPANE INSIDE A PROPANE TANK MEETING THE SPECIFATIONS BELOW, UNDER THE CONDITIONS LISTED BELOW. THIS DEVICE IS INTENDED FOR OUTDOOR USE ONLY. WARNING USE OF THIS DEVICE IN A MANNER OTHER THAN STATED IN THIS MANUAL, MAY RESULT IN IMPAIRMENT OF THE DESIGNED SAFETY PROTECTION AND THUS AN UNSAFE CONDITION.
PAGE 2
General Instructions & Warnings Only install this device as described below. No field assembly is required. The sync process to the app on your smart device, as described below, should occur in an area clearly out of any explosive atmosphere. Once device is synced to the smart device/app, the device is “in service” and operating normally. Device will then operate continually until battery is exhausted. There is no “Power Off” mode from that point forward.
PAGE 3
OPERATING INSTRUCTIONS Smart Device/App Users 1. 2. Go to your app store. Search for Mopeka Tank Check app and install. Launch the app. When it starts it will automatically start a search for Mopeka 3. Press and hold SYNC button until sensor appears on app. (up to 10 seconds) Mopeka Products LLC ✓ sensors. www.mopeka.
PAGE 4
. The sensor will then appear on your app as a new device. 5. Sensor is now Sync’d . You may now proceed to installing the sensor on the tank. Mopeka Products LLC www.mopeka.
PAGE 5
6. 7. 8. Install Sensor on Tank Clean the bottom of the tank of any debris, excess paint, and rust. Check your tank for adequate bottom clearance to install the sensor. (If using on a small vertical tank like 20, 30, or 40 lbs., or certain 100lb tanks, then you will need to place wood blocks, pavers, or similar under the tank to provide clearance. But in all other cases this should not be an issue. Apply ultrasonic grease to the contact pad between the magnets.
PAGE 6
Mopeka Products LLC www.mopeka.
PAGE 7
REVISION TABLE REVISION A DESCRIPTION RELEASE Mopeka Products LLC DATE 2019.09.19 www.mopeka.
PAGE 8
Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generate, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.