Owner's manual

ManualsBrandsVestil ManualsEquipmentCP Series

Cable Puller Manual 1010 10/14/2010 update

Page 1 of 8

CP-SERIES CABLE PULLERS

INSTRUCTION MANUAL

MODEL CP-15 & -30

VESTIL MANUFACTURING CORP.

2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703

TELEPHONE: (260) 665-7586 -OR- TOLL FREE (800) 348-0868

FAX: (260) 665-1339

URL: WWW.VESTILMFG.COM EMAIL: SALES@VESTIL.COM

NOTE: COMPLIANCE WITH REGULATIONS, CODES, AND/OR STATUTORY (NON-VOLUNTARY) STANDARDS

ENFORCED IN THE LOCATION WHERE THE DEVICE IS USED IS EXCLUSIVELY THE RESPONSIBILITY OF THE END-USER. IF

LAW ENFORCED WHERE THE CABLE PULLER IS USED CONTRADICTS AN INSTRUCTION(S) OR PART OF AN

INSTRUCTION(S), VESTIL IS NOT RESPONSIBLE FOR ANY CONSEQUENTIAL DAMAGES SUSTAINED AS A RESULT.

Table of Contents Table of Figures

Product Introduction……………………………….... 2 Fig. 1A “Side view”……........................................................... 4

Safety Principles……………………........................ 2 Fig. 1B “Top view”…................................................................ 4

Safety Guidelines………………….......................... 3 Fig. 1C “View of cable opening”………………………………… 4

Use Instructions……………………………………… 5-6 Fig. 2 “Product label placement”.…………….………………....

Maintenance Recommendations…………............. 6-8

Summary of content (8 pages)

PAGE 1
Cable Puller Manual 1010 10/14/2010 update CP-SERIES CABLE PULLERS INSTRUCTION MANUAL MODEL CP-15 & -30 VESTIL MANUFACTURING CORP. 2999 NORTH WAYNE STREET, P.O. BOX 507, ANGOLA, IN 46703 TELEPHONE: (260) 665-7586 -OR- TOLL FREE (800) 348-0868 FAX: (260) 665-1339 URL: WWW.VESTILMFG.COM EMAIL: SALES@VESTIL.COM NOTE: COMPLIANCE WITH REGULATIONS, CODES, AND/OR STATUTORY (NON-VOLUNTARY) STANDARDS ENFORCED IN THE LOCATION WHERE THE DEVICE IS USED IS EXCLUSIVELY THE RESPONSIBILITY OF THE END-USER.
PAGE 2
PRODUCT INTRODUCTION Thank you for purchasing a CP-series cable puller (“cable puller,” “CP,” or “puller”). Our cable pullers are durable, high-quality products that have been rigorously engineered to provide both dependable operation and simplicity. Although use and maintenance procedures are relatively intuitive, any person who might use or maintain this product must be familiar with the instructions provided in this manual.
PAGE 3
SAFETY GUIDELINES Failure to read and understand the instructions included in this manual before using or servicing the cable puller constitutes misuse of the product. Study the entire manual before installing the product. Read the manual to refresh your understanding of the safe use and maintenance procedures explained on p. 5-8. DO NOT attempt to resolve any problem(s) with the device unless you are both authorized to do so and certain that it will be safe to use afterwards.
PAGE 4
Labeled Photographs **Note: Vestil does NOT provide replacement parts for this product. The following diagram is solely intended to clarify terms that appear in the Use (p. 5-6) and Maintenance Instructions (p. 6-8).** FIG. 1A: Side View B D E C A F Openings for mounting pin G FIG. 1B: Top View F B C D E G A ITEM LETTER FIG.
PAGE 5
Use Instructions: The operating instructions in this manual should supplement the operation recommendations of ASME B30.21. Only trained, designated persons should use the cable puller. “Designated person” means someone selected by his or her employer, or by a representative of the employer, as competent to use the cable puller. Maintenance persons and personnel who perform tests also may use the cable puller when necessary to fulfill their employment responsibilities.
PAGE 6
Step 7: Slide the operator handle onto the forward ratcheting lever; then work the forward ratcheting lever back-andforth until approximately 5 feet of cable has passed through the puller. Operator handle Notch for retaining pin (Handle) retaining pin Open end of operator handle Step 8: Connect the load to the cable hook by suitable means. The cable must form a straight line between the puller and the load. Test the soundness of the connection.
PAGE 7
Inspections before EACH use: visual examination should be performed by a person qualified and selected to evaluate the condition of cables and cable pullers prior to each use. In particular, the selected person should inspect the following items and prepare a written record describing the findings of the inspections: 1. Cable puller: visually inspect the puller for loose bolts/nuts, excessive wear of the mounting pin or cable guide.
PAGE 8
 A modification is a change that alters the puller from normal operating condition, like bending the structural members. NEVER modify the puller without the express, written approval of Vestil, because modifications might render it unsafe to use. Step 4: Perform complete “Before each use” and “Periodic” inspections. Step 5: Make a dated record of the repairs and/or adjustments made. Markings: Only use the cable puller if all labels are readable and undamaged. FIG.