User`s manual

ManualsBrandsVIA Technologies ManualsComputer equipmentVT8237R PLUS

User’s Manual I

ENDAT-3400M

User’s Manual

Rev. 1D

For ENDAT-3400M PCB Rev: 1C or Later

09/29/2006

The ENDAT-3400M System Board

The content of this manual has been checked for accuracy. The manufacturer

assumes no responsibility for any inaccuracies that may be contained in this

manual. The manufacturer reserves the right to make improvements or

modification to this document and/or the product at any time without prior

notice. No part of this document may be reproduced, transmitted, photocopied or

translated into any language, in any form or by any means, electronic, mechanical,

magnetic, optical or chemical, without the prior written permission of the

manufacturer.

VIA 'Luke' CoreFusion™ is registered trademark of VIA Technology Incorporation

VT8237R Plus may only be used to identify products of VIA Technology

Multiscan is a trademark of Sony Corp of America

IBM, EGA, VGA, PC/XT, PC/AT, OS/2 and PS/2 are registered trademarks of

International Business Machines Corporation

Plug and Play is registered trademarks of Intel Corporation

Microsoft, Windows and MS-DOS are trademarks of Microsoft Corporation

Award is a trademark of Phoenix Software Inc.

PCI is a registered trademark of PCI Special Interest Group

All trademarks are the properties of their respective owners.

Other product names mentioned herein are used for identification purpose only and

may be trademarks and/or registered trademarks of their respective companies.

Installation Notice

The manufacturer recommends using a grounded plug to ensure proper

motherboard operation. Care should be used in proper conjunction with a

grounded power receptacle to avoid possible electrical shock. All integrated circuits

on this motherboard are sensitive to static electricity. To avoid damaging

components from electrostatic discharge, please do not remove the board from the

anti-static packing before discharging any static electricity to your body, by wearing

a wrist-grounding strap. The manufacturer is not responsible for any damage to the

motherboard due to improper operation.

Summary of content (27 pages)

PAGE 1
I User’s Manual ENDAT-3400M User’s Manual II The ENDAT-3400M System Board Copyright Notice The content of this manual has been checked for accuracy. The manufacturer assumes no responsibility for any inaccuracies that may be contained in this manual. The manufacturer reserves the right to make improvements or modification to this document and/or the product at any time without prior notice.
PAGE 2
III User’s Manual IV Specification: TABLE OF CONTENTS Model ENDAT-3400M Form Factor System Chipset Mini-ITX 170 mm x 170 mm (6.69”x6.69”) CPU Supporting Memory Ethernet VGA LCD interface Duo View Video Interface Serial / Parallel Watchdog Timer IDE Connector SATA Connector AUDIO Expansion Slot I/O Port Digital IO RS-422/485 USB Port Power Supply The ENDAT-3400M System Board VIA LUKE / LUKE-Lite (NB+CPU) + VIA VT8237R Plus(SB) Supports 133MHz FSB by VIA Luke integrated Eden-N 533MHz/800MHz/1.
PAGE 3
User’s Manual V CHPATER 4. VGA, LCD, FEATURE.............................................. 34 4-1. VGA FEATURE....................................................................................... 34 4-2. LVDS PANEL FEATURE......................................................................... 35 4-3. PCI BUS AUDIO ADAPTER FEATURES................................................ 36 4-4. DRIVER UTILITY INSTALLATION GUIDE ............................................. 37 CHPATER 5. LAN ADAPTER ..........
PAGE 4
User’s Manual 1 Chapter 1. Introduction ENDAT-3400M supports high performance processor of VIA Luke CoreFusion. It also supports high speed DDR memory with 64-bit wide interfaces with non-ECC DIMM (up to 1GB). Only Double Data Rate (DDR) SDRAM memory is supported and the speed of memory can be 200, 266, 333 and 400 MHz. ENDAT-3400M provides an integrated graphics (S3 Graphics UniChrome™ Pro IGP) accelerator delivering cost competitive 3D, 2D, and video capabilities.
PAGE 5
User’s Manual 3 1-2. Unpacking The motherboard comes securely packaged in a sturdy cardboard shipping carton. In addition to the User's Manual, the motherboard package includes the following items: ENDAT-3400M System Board HDD / IO Cables CDROM Driver includes: Drivers for Windows 98, ME, 2000, XP and AMI/AWARD FLASH ROM utilities. If any of these items are missing or damage, please contact the dealer from whom you purchase the motherboard.
PAGE 6
5 User’s Manual Chapter 2. Setting up the Motherboard 2-1.
PAGE 7
User’s Manual JP8, JP9: RS232 / 422 / 485 Selector for COM2 (2.0mm) TYPE JP8 (3x4/2mm) JP9 (2x7/2mm) RS-232 * 1-2, 4-5, 7-8, 10-11 1-2 RS-422/485 2-3, 5-6, 8-9, 11-12 3-4, 5-6 JP12: Box Header for Case Panel (2.54mm) Pin No. Function HDD active LED 1(-), 2(+) External Speaker 3,6 Buzzer On/Off 4,5 Hardware Reset Switch 7,8 ATX Power On/Off 9,10 Power LED 11(-),12(+) Close: Enable WDT function 13,14 JBAT1: CMOS Data Clear (2.
PAGE 8
User’s Manual 9 J1: Power Supply Connector 2 pin wafer (3.96mm) Pin No. Function Pin No. Function 1 +12V 2 GND JUSB1 JUSB2: Box Header Type Connector for USB port (2.54mm) Pin No. Function Pin No. Function USB_VCC USB_VCC 1 2 USBD2-/4USBD3-/53 4 USBD2+/4+ USBD3+/5+ 5 6 USB_GND USB_GND 7 8 USB_GND USB_GND 9 10 CD_IN1: CD IN Box Header Connector (2.54mm) Pin No. Function Pin No. Function 1 LEFT 2 GND 3 GND 4 RIGHT SPDIF: SPDIF Box Header Connector (2.54mm) Pin No. Function +5V 1 N.C.
PAGE 9
11 User’s Manual IDE1, IDE2 Connector Pin No. Description IDE Reset# 1 IDE data7 3 IDE data6 5 IDE data5 7 IDE data4 9 IDE data3 11 IDE data2 13 IDE data1 15 17 IDE data0 19 GND 21 IDE REQ IDE IOW# 23 IDE IOR# 25 IDE Ready 27 IDE ACK# 29 IDE IRQ 31 IDE A1 33 IDE A0 35 IDECS1# 37 HDLED# 39 12 The ENDAT-3400M System Board Slim IDE2 Connector (44Pins with 2.0mm) Pin No.
PAGE 10
13 User’s Manual LVDS1: Dual LVDS Channel (2.0mm) Pin No. 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 Signal VBL (+12V) GND DISP.ON/OFF LCD Power GND TxO0+ TxO1+ TxO2+ TxO3+ TxOC+ GND TxE0+ TxE1+ TxE2+ TxE3+ TxEC+ LCD Power GND GND VBL (+12V) Pin No. 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 14 The ENDAT-3400M System Board 2-2.
PAGE 11
15 User’s Manual In the PCI Bus design, the BIOS is automatically assigned an IRQ to a PCI slot that has a card in it which requires an IRQ. To install PCI cards via riser card, you need to set the correct "ADSEL" and "INT" (interrupt) assignment on the jumper of riser card.
PAGE 12
17 User’s Manual 2-7. Digital I/O 1) Pin out of digital I/O header (JP11): Pin No. 1 3 5 7 9 11 13 Function DIO-O0 DIO-O1 +12V KEY GND DIO-O2 DIO-O3 Pin No. 2 4 6 8 10 12 14 Function DIO-I0 DIO-I1 +12V +5V GND DIO-I2 DIO-I3 2) Digital I/O port address: This function is support by onboard super I/O chip; it can be control easily by change the register of super I/O chip via I/O port “2Eh” and “2Fh”. Please see the sample code of below for implement. Voltage tolerance: +/- 5% with 0V to +5V.
PAGE 13
19 User’s Manual 20 The ENDAT-3400M System Board 3-1. Standard CMOS Features 3-2. Advanced BIOS Features The Standard Setup is used for the basic hardware system configuration. The main function is for Data/Time and Hard Disk Drive settings. This section allows you configuring your system for basic operation. You have the opportunity to select the system’s default speed, boot-up priority, keyboard operation and security.
PAGE 14
21 User’s Manual 3-3. Advanced Chipset Features This section allows you to configure the system based on the specific features of the installed chipset. This chipset manages bus speeds and the access to the system memory resources, such as DRAM and the external cache. It also coordinates the communications with the PCI bus. It must be stated that these items should never be altered. The default settings have been chosen because they provide the best operating conditions for your system.
PAGE 15
23 User’s Manual ․Panel Type ID No. 0 1 2 3 4 5 6 7 24 The ENDAT-3400M System Board ․V-Link mode selection Resolution 640 x 480 800 x 600 1024 x 768 1280 x 768 1280 x 1024 1400 x 1050 1600 x 1200 1366 x 768 Channel 1 1 1 1 2 2 2 1 If you apply one of the standard panels shown above, select the appropriate option according to the type of panel that you apply. Or, please contact your dealer or sales representative for custom-made BIOS that will suit the panel that you apply.
PAGE 16
25 User’s Manual 26 The ENDAT-3400M System Board VIA OnChip IDE Device Item OnChip SATA SATA Mode OnChip IDE Channel0 OnChip IDE Channel1 IDE Prefetch Mode Primary Master PIO Primary Slave PIO Secondary Master PIO Secondary Slave PIO Primary Master UDMA Primary Slave UDMA Secondary Master UDMA Secondary Slave UDMA IDE HDD Block Mode Available Options: Enabled IDE Enabled Enabled Enabled Auto Auto Auto Auto Auto Auto Auto Auto Enabled ․SATA Mode These fields are used to select the RAID/IDE mode of the
PAGE 17
27 User’s Manual SuperIO Device Item Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select RxD, TxD Acitve IR Transmission Delay UR2 Duplex Mode Use IR Pins Onboard Parallel Port Parallel Port Mode EPP Mode Select ECP Mode Use DMA 28 The ENDAT-3400M System Board 3-5. Power Management Setup Available Options: 3F8/IRQ4 2F8/IRQ3 Normal Hi,Lo Enabled Half IR-Rx2Tx2 378/IRQ7 Normal EPP1.7 3 ․UART Mode Select Select an operating mode for the serial port.
PAGE 18
29 User’s Manual 30 The ENDAT-3400M System Board IRQ/Event Activity Detect Item PS2KB Wakeup Select PS2KB Wakeup from S3/S4/S5 PS2MS Wakeup from S3/S4/S5 USB Resume from S3 VGA LPT & COM HDD & FDD PCI Master Modem Ring Resume RTC Alarm Resume Date (of Month) Resume Time (hh:mm:ss) IRQs Activity Monitoring Available Options: Hot key Disable Disabled Disabled OFF LPT/COM ON OFF Disabled Disabled 0 0: 0: 0 Press Enter ․PS2KB Wakeup Select When selecting “Password”, press to change password.
PAGE 19
31 User’s Manual 3-6. PnP/PCI Configurations This section describes the configuration of the PCI bus system. PCI is a system that allows I/O device to operate at speeds nearing the speed of the CPU itself, when communicating with its own special components. This section covers some very technical items. It is strongly recommended that only experienced users make any changes to the default settings.
PAGE 20
33 User’s Manual 3-8. Frequency / Voltage Control Frequency/Voltage Control Item VIA C3 Clock Ratio Auto Detect PCI/DIMM Clk Spread Spectrum CPU Host/3V66/PCI Clock Available Options: Default Enabled Disabled Default ․VIA C3 Clock Ratio This item is for VIA C3 CPU Ratio adjustment. ․Auto Detect DIMM/PCI Clk When enabled, the system will automatically send clock signals to existing PCI devices. ․Spread Spectrum Leave this field in its default setting.
PAGE 21
User’s Manual 4-2. 35 LVDS Panel Feature 36 The ENDAT-3400M System Board 4-3. PCI Bus Audio Adapter Features The on-board graphic controller supports industry standard LCD panel, LVDS interface only, with 1 channel (18 or 24) and 2 channels (36 or 48bit) data width. The Chipset built-in SoundBlaster Pro Hardware and Direct Sound Ready AC97’ Digital Audio Controller LVDS interface provides low voltage, high speed and low EMI serial DC-balanced differential data via optional onboard LVDS.
PAGE 22
User’s Manual 4-4. 37 Driver Utility Installation Guide 5- When finishing the installation of Windows platform (95/98/2000/NT), please install the relative VIA driver (4in1) utilities for compliance compatibility of hardware environment. 6- Insert the support CD that supplied with motherboard into CD-ROM driver which enable the access with auto-run mode; or double –click the CD driver icon in “My Computer” to bring up the screen.
PAGE 23
User’s Manual 39 Chapter 5. LAN Adapter The on-board LAN adapter integrated of Single Chip Fast Ethernet Controller with options of one or dual LAN solution, and also the LAN chip option of VIA VT6103 solution. It is highly integrated and requires no “glue” logic external memory on board. It runs in the bus master mode and directly sending/receiving Ethernet packet to/from memory. The On-board LAN adapter can directly fetch the system CPU.
PAGE 24
User’s Manual 41 5-3. Connecting 100Base-TX Fast Ethernet Network The system board provides an RJ-45 port for connection to 100Base-TX Fast Ethernet or 10Base-T Ethernet Network with a single connection over unshielded twisted-pair (UTP). The adapter automatically operates at 10Mbps or 100Mbps when the appropriate 10/100Base hub is connected. To connect the adapter to 100Base-TX Fast Ethernet Network, you need a twisted-pair Category 5 cable with RJ-45 modular jacks at both ends.
PAGE 25
43 User’s Manual Appendix A: FLASH Memory Utility Using this utility to update the system BIOS from a disk file to the on board Flash memory. Be aware the improper change of the system BIOS will cause the system to malfunction. Using utility as follows: 1. Insert the FLASH memory utility distribution floppy diskette in drive A: 2. At the DOS prompt, type A:>AWDFLASH and press AwardBIOS FLASH Utility V8.36E C>Phoenix Technologies Ltd.
PAGE 26
45 User’s Manual Appendix C: UC-COM56 Jumper Setting JP1: COM3, 4 Voltage Selector (2.0mm) Voltage +12V(DC) R.I. * COM4 (JP1) 1-2 3-4 COM3 (JP1) 7-8 9-10 +5V(DC) 5-6 11-12 JP2: COM5, 6 Voltage Selector (2.0mm) Voltage +12V(DC) R.I. * COM6 (JP2) 1-2 3-4 COM5 (JP2) 7-8 9-10 +5V(DC) 5-6 11-12 J2: Digital I/O Box Header Connector (2.54mm) Pin No. Function Pin No.
PAGE 27
47 User’s Manual z RMA SERVICE REQUEST FORM When requesting RMA service, please fill out this “RMA Service Request Form”. This form needs to be shipped with your returns. Service cannot begin until we have this information. RMA NO.: Company: Person to Contact: Phone No: Purchase Date : Fax No. : 48 Applied Date : Issue Code of defect. 01 Second Times R.M.A.