5”/17”TFT-LCD MONITOR V150/ V171 USER’ S MANUAL Rev. 1.1 www.viewera.
CONTENTS 1. Introduction Product Description ........................................................................................ Page 1 Package Contents Product Features …......................................................................................... Screen Cleaning Techniques Additional 2. Control Functions ……………………………………………………...….. 3. Input Diagrams ............................................................................................. 4. Installation.................................
1. Introduction Product Description Congratulations on your purchasing ViewEra 15”/17”LCD monitor. It incorporates high quality display into a small light weighted module. It has power-saving capabilities and emits no radiation. You will certainly benefit from this monitor in lots of ways; to name some of them: comfort, safety and environmental protection. This LCD monitor incorporates color active matrix thin-film-transistor (TFT) liquid crystal display to provide superior display performance.
Product Features High brightness, high contrast ratio and quick response tiem. Built-in speakers. Power management system conforms to VESA DPMS standard. Support Plug & Play, no need for driver installation. Advanced OSD controls for picture quality adjustment. Detachable stand for wall-mounting with VESA 75 (mm) bracket.
Additional Read all of these instructions and save them for later use. Follow all warnings and instructions on the product. Product ♦Do not cover block the vent holes in the case. ♦Do not insert sharp objects or spill liquid into the LCD monitor through cabinet slots. They may cause accident fire, electric shock or failure. ♦Disconnect the power plug from the AC outlet if you will not use it for an extended period of time.
Power and extension cords ♦Do not allow anything to rest on the power cord. ♦Do not locate this product where persons will walk on the cord. ♦Use the proper power cord with correct attachment plug type. If the power source is 120V AC, use a power cord that has UL and C-UL approvals. If the power source is a 240V AC supply, use the tandem (T blade) type attachment plug with ground conductor power cord that meets the respective European country’ s safety regulations, such as VDE for Germany.
2. Control Functions a.【PC,Audio,DVI】 Control Button Front View (Model : V150、V171 series) ﹝2﹞ ﹝5﹞ ﹝1﹞ ﹝3﹞ ﹝4﹞ 1. Power switch Power switch & LED. 2. Auto adjust Press this button to obtain the best display quality. 3. Adjust (decrease －) This button is used to decrease the value of selected function. 4. Adjust (increase ＋) This button is used to increase the value of selected function. 5. OSD menu / Enter Press this button and the OSD menu pops up on the screen.
OSD Controls Monitor Function Selection Menu： AUTO ADJUST BRIGHTNESS CONTRAST CLOCK PHASE H-POSITION V-POSITION Press this button to obtain the best display quality. Adjust the brightness by using ＋ and － buttons. Adjust the contrast by using ＋ and － buttons. Adjust the clock by using ＋ and － buttons. Adjust the phase by using ＋ and － buttons. Press ＋ to move the image to right. Press － to move the image to left. Press ＋ to move the image upward. Press － to move the image downward.
Tools Menu： Adjust the volume by using ＋ and － buttons. VOLUME MUTE Speakers are inactive.
Color Temperature and RGB Adjusting Menu： COLOR TEMP. Adjust the color temperature of the display. RED Adjust red pixel luminance. GREEN Adjust green pixel luminance. BLUE Adjust blue pixel luminance.
OSD Function Selection Menu： EXIT OSD OSD–H–POSITION OSD–V–POSITION OSD DURATION LANGUAGE Exit the OSD menu. Press Press Press Press ＋ － ＋ － to move the OSD menu to right. to move the OSD menu to left. to move the OSD menu upward. to move the OSD menu downward. Set the OSD display time. Set the OSD display language.
3. Input Diagrams Inputs 【PC】 1 2 3 【1】DC IN This is for connecting the adapter DC 12V/3A (4A) cable. 【2】LINE IN This can be connected to the audio-out jack of any sound card. 【3】VGA (Analog) IN This can be connected with the D-sub 15 pin signal connector.
4. Installation Electrical Connection Please follow the instruction below to properly connect the LCD monitor to external electrical source. 1. Connect the female-end of the power cable to the transformer. Connect the male-end of the power cable to the wall outlet or extension cable. 2. Connect the cable from the other end of the transformer to the LCD monitor DC IN located at the back of the LCD monitor. Signal Connection 1. Power off both the LCD monitor and PC system before connecting them. 2.
5. Product Specifications a. 15”LCD monitor Model Spec Display type 15”active matrix TFT LCD panel Pixel pitch 0.297(H) x 0.297(V) mm Max. resolution 1024(H) x 768(V) XGA Contrast ratio 400 : 1 Brightness 250 cd/m2 Response time 25 ms V150 Display color 16.
V150 Display Modes Mode 1 2 3 4 5 6 7 8 9 10 11 12 Resolution 640 × 350 640 × 480 640 × 480 640 × 480 720 × 400 800 × 600 800 × 600 800 × 600 800 × 600 1024 × 768 1024 × 768 1024 × 768 H Freq (KHz) 31.469 31.469 37.861 37.500 31.469 35.156 37.879 48.077 46.875 48.363 56.476 60.023 Page 13 V Freq (Hz) 70.0 59.9 72.8 75.0 70.0 56.2 60.3 72.1 75.0 60.0 70.0 75.
b. 17〞LCD monitor. Model V171 Spec LCD Display 17”Active matrix TFT LCD panel Pixel Pitch 0.264(H) x 0.264(V) mm Max. Resolution 1280(H) x 1024(V) SXGA Contrast Ratio 400 : 1 Brightness 250 cd/m2 Response Time 25 ms Display Color 16.
V171 Display Modes Mode 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Resolution 640 × 350 640 × 480 640 × 480 640 × 480 720 × 400 800 × 600 800 × 600 800 × 600 800 × 600 1024 × 768 1024 × 768 1024 × 768 1280 × 1024 1280 × 1024 H Freq (KHz) 31.469 31.469 37.861 37.500 31.469 35.156 37.879 48.077 46.875 48.363 56.476 60.023 63.981 79.760 Page 15 V Freq (Hz) 70.0 59.9 72.8 75.0 70.0 56.2 60.3 72.1 75.0 60.0 70.0 75.0 60.0 75.
6. Dead Pixel Policy Dead pixels on the TFT LCD panel are sometimes inevitable. ViewEra guarantees that the monitor will be replaced if the number of dead pixels on our monitor exceeds 5 pixels within the first year from the date of purchase. 7. Warranty and Customer Service Warranty ViewEra warrants the 15” /17”TFT-LCD monitors for one year LCD panel and backlight, three years parts and labor from the date of purchase. For detail information, please refer to our website. (http:// www.viewera.com/warranty.
8. Windows setup For the best display quality, please set the monitor type in Windows. Control Panel > Display > Settings > Advanced > List All Modes For V150, please set to “XGA 1024 × 768 @ 75Hz.
For V171, please set to “SXGA 1280 × 1024@75Hz.
9. Trouble Shooting 1) Power on but no picture → Make sure the VGA cable is tightly connected from the video output connector on the video card to the video input connector on the monitor. → Make sure you are using the standard power adapter coming with the monitor. → Ch e c ky ourvi de oc a r di ft h edr i v e ri sc or r e c t l yi ns t a l l e d.I ft h e r ei sn ovi de os i gn a lf r omt h evi de oc a r d,“ NO INPUT SIGNAL”will show on the screen.
4) Display position is incorrect → Us e“ Auto Tuning”function to adjust image position on the OSD menu or you can hold button 2 for 3 seconds to do auto tuning. 5) Speakers have no sound → Ma kes ur et h ea udi oc a bl ei st i gh t l yc onn e c t e df r omt h ea udi oou t pu tj a c kont h ePCt ot h ea u di oi nputj a c k on the monitor. 6) Residue image →I fa ni ma ger e ma i nsont h es c r e e nf ora ne x t e n de dpe riod of time, it may be imprinted in the screen and leave a residue image.
Boot the computer into VGA Mode (F8) [repeatedly] at startup. Go to “ Control Panel” , double click on “ Display” , click on the SETTINGS TAB, and click on the ADVANCED button. Then Click on the Adapter TAB, click “ List All Modes”and change the screen resolution to 1280x1024. (You can select 16 bit or 32 bit color which depends on your video card capability.) Select “ 1280 by 1024, High Color (16 bit), Default Refresh” Click on the “OK”and “ APPLY”.
