fea VIGOR INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE (MODEL VG06061) /\ SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated by these symbols. /A\ WARNING Instructions that, if ignored, could result in death or serious personal injury caused by incorrect handling or installation of the product. These instructions must be observed for safe installation. /\ CAUTION The instructions for the following unit is b
INSTALLATION INSTRUCTIONS FOR STANDING SHOWER CABIN I ee er ras OWNER'S MANUAL PLEASE READ INSTRUCTIONS BEFORE PROCEEDING Packing List 1. Wall connector {2pc) 2. Structural arm {2pc) 3. Support assembly (2pc} 4. Side glass panel (with hinge slots, 1pc} 5. Side glass panel (without hinge slots, 1pc) 6. Side seal strip (2pc) 7. Glass support (4pc) 8. Hinge (2pc) 9. Bottom rail(3 pc) 10. Door magnetic seal strip (2pc} 11. Bottom comer joint (2pc) 12. Handle assembly {1pc) 19 13. Door (1pc) 14.
HTTP. /Industriousness. com 1-866-591-7792 1. WALL CONNECTOR | 2. STRUCTURAL ARM 3.SUPPORT ASSEMBLY| 4. SIDE GLASS PANEL |5. SIDE GLASS PANEL 98001 98002-38 88003 97001-3868 7006-38 88002-38 97001-38 87008-38 50) 88002-40 87001-40 97006-40 = B88002-42 87001-42 7006-42 & 6. SIDE SEAL STRIP 7.GLASS SUPPORT 8. HINGE ASSEMBLY | 9. BOTTOM RAIL 3pc. 10. DOOR MAGNETIC 85001-368 SEAL STRIP 98001 88004 28015 95001-38 85001-42 11. BOTTOM CORNER 12. DOOR HANDLE 13. DOOR 14. DOOR SIDE 15.
HTTP. /Industriousness. com 1-866-591-7792 /\ WARNING WE STRONGLY RECOMMEND THAT A LICENSED PROFESSIONAL INSTALL THIS SHOWER CABIN AND INCLUDE THE ASSISTANCE OF A SECOND PERSON TO INSTALL THE DOOR UNIT. INSTALLATION OF THE SHOWER DOORS BY AN INEXPERIENCED PERSON MAY RESULT IN GLASS BREAKAGE AND, CONSEQUENTLY, CAUSE PERSONAL INJURY OR DEATH. BEFORE STARTING Compare items on your invoice with what you have received. Carefully review the Packing List on page 2.
HTTP. /Industriousness. com 1-866-591-7792 PREPARATION STEPS TO FOLLOW BEFORE INSTALLATION 1. Remove the plastic layer from the base border (if needed). Do NOT remove the plastic layer off the plastic platform of the base. 2. Properly apply silicone to the wall and base joints. & IMPORTANT . To prevent damage to the finish, you should protect the shower cabin bottom with a cardboard protector before beginning the installation. .
HTTP. /Industriousness. com 1-866-591-7792 by “THIS EDGE LOOKS ~ INSIDE OF THE SHOWER \ { TOP REMOVES TO | 4 INSTALL 3/4" screw THIS EDGE LOOKS —11 = OUTSIDE OF THE SHOWER = FIG B. INSTALLING SIDE GLASS PANEL 1. Arrange glass to the preferred configuration. (see diagram on page 4) 2. Select the door opening location on the shower cabin. 3. Install the side seal strip (#6) to the wall side of the hinged side glass panel [SEE FIG.3] 4.
C. GLASS SUPPORT (7) / J SCREW (17) ac(j-— HEX Sore W SIDE GLASS PANEL | GASKET VIEW FROM THE TOP FIG HANDLE INSTALLATION 1. Assemble the door handles (#12) to the door [SEE FIG 5] HINGE INSTALLATION 13 12 HTTP. /Industriousness. com 1-866-591-7792 FIG Clean the glass surface on the side glass panel (#4) where the hinges (#8) are to be installed with rubbing alcohol. Position hinges on the side glass panel. [SEE FIG.6] Place washers on each side of the side glass panel.
industriousness com INSTALLING THE WATER SEAL STRIP 1-866-591-7792 Clean the side glass panel (#4) edges where the door side seal strip (#14) and the door bottom seal strip (#15) are to be installed with rubbing alcohol. Cut the seal strips according to the diagram. [SEE FIG.7] Verify that the lips of both seal strips face toward the inside of the shower cabin before seal strip installation. Install the seal strips according to the diagram.
hip /Avow industriousness 1-866-581-7792 /\ WARNING DOOR PANEL INSTALLATION REQUIRES TWO OR MORE PEOPLE TO ASSIST F. INSTALLING THE DOOR 1. 2. 3. Clean the door (#13) glass surfaces where the hinges (#8) are to be installed with rubbing alcohol. Position the door onto the hinges. Hold securely in place. Place a thin gasket (supplied) on each side of the door between the glass and hinge while holding the door in place. Install the hinges as illustrated [SEE FIG.8]. Use the hex key supplied.
H. hip /Avow industriousness 1-866-691-7792 APPLYING THE SILICONE Apply clear silicone caulking to the inside between the wall and side seal strip. Apply clear silicone caulk to the inside between the bottom of side glass panels (#4, #5) and bottom rail. Apply clear silicone caulk around the inside perimeter of the bottom rail. [SEE FIG.10] INSTALLING HEX SCREW COVERS Install hex screw covers (#21) to the hex screws that mount the hinges, wall connectors, and glass supports. FIG.10 /I\ IMPORTANT e WAIT 24 H
hip /Avow industriousness 1-866-691-7792 CLEANING INSTRUCTIONS FOR THE SHOWER CABIN AND DOOR PANEL A. Use mild liquid household cleaners to keep metal surface bright and clean. Rinse well and dry with a clean cloth. B. Remove dust with a soft, damp cloth. C. Use rubbing alcohol to clean and remove grease, oil, paint, and ink. D. Accidental scratches or stains will rarely show. If they do show, they can be easily removed with a liquid automobile polish. A IMPORTANT .
HTTP. /Industriousness. com 1-866-591-7792 VIGOR INDUSTRIES, LLC ("VIGOR) SHOWER ENCLOSURE LIMITED LIFETIME WARRANTY EFFECTIVE JANUARY 1, 2010 VIGOR offers the following limited warranty on sate of its Shower Enclosure products* (the Product’) and the components thereof. This warranty extends only to the original owner or end-user for personal household use. For commercial uses, additional imitations apply.