Specifications
DIP Switches shown
in the factory default
positions
DOOR ENTRY / CCTV VIDEO
/ PAGING CONTROLLER
VIKING
©
MODEL C-1000B
PWR 13.8 VAC
DOOR
STRIKE 1
DOOR
STRIKE 2
DOORBOX 2
DOORBOX
PWR OUTPUT
DOORBOX 1
123456789
10 11 12 13
14 15 16 17 18 19
EARTH
GND
PHONE LINE
INPUT
LINE OUT
TO PHONES
KEYLESS CONTACT
CLOSURE INPUT
VIKING
ELECTRONICS
HUDSON, WI 54016
EARTH
GND
C.O. LINE
INPUT
OUT TO
PHONES
KEYLESS
C.C. INPUT
DOOR
BOX 1
DOORBOX
13VAC PWR
DOOR
BOX 2
N.O. COM N.C.
DOOR STRIKE 1
SIG GND
VIDEO 1 IN
SIG GND
VIDEO 2 IN
SIG GND
VIDEO OUT
N.O. COM N.C.
DOOR STRIKE 2
TALK BATTERY
OFF ON
C
LED1
C
LED2
C
LED3
ON
1 2 3
COM N.O. N.C. - - - - AUX.
CONTACT
OUTPUT
ON
OFF
1 2 3
ON
Switch
1
1
2
2
3
3
E. Dip Switch Programming
Position
OFF
ON
OFF
ON
OFF
ON
Description
Doorstrike Activation = 0.5 seconds (factory setting)
Doorstrike Activation = 10 seconds
Normal Mode (factory setting)
Security Code Bypass Mode
Line Concentrator Mode
Normal Operation (factory setting)
F. Mode Descriptions
Entering these codes while in programming will switch the C-1000B into the corresponding mode.
Disable Special Modes (✱0): This command disables (clears) all the special modes listed below. Enter this command before pro-
gramming the rest of the selections to be sure no unwanted modes are set.
Doorbell Mode (✱1): In this mode, the ring signal from either doorbox is prevented from going through to the “LINE OUT TO
PHONES“ terminals. This is useful when a conventional door bell is connected to the auxiliary contacts. Now when someone acti-
vates a doorbox, the doorbell will chime rather than the phone ringing (see Programming section B).
Custom Ring Mode (✱2): With this mode selected, the ring signal from the device ports are interrupted in a double burst pattern,
making it easier to determine if the incoming call is from a doorbox or the C.O. line. Note: Some telephones and phone systems
are not compatible with this feature.
Multiple Relay Activation Mode (✱3): If selected, after a door strike command is entered, the phone is switched back to the door-
box port so additional doorstrike (relay activation) commands can be entered. This is useful when letting someone through your
gate with the first command then unlocking your front doorstrike with a second command. To return to the call on hold, enter “#”.
Paging Mode (✱4): In this mode a paging system that provides talk battery (Viking PA-2A or CPA-7B) can be connected to one of
the doorbox ports. When the person on the phone wants to make a page, they can enter “#” and a “1” or “2” depending on which
port the paging amplifier is on. After the announcement is made another “#” will return them to the phone conversation.
Analog PABX/KSU Station Mode (✱5): This mode is ideal when installing the C-1000B on a phone system that does not have a
spare trunk port but does have an unused analog station port. This mode allows any standard (POTS) telephone such as the E-10,
E-20A, E-30 or K-1700-3 to be used in place of Doorbox 1. Only one door phone can be used in this mode. When the door phone
goes off-hook, a hot-line dialer or ringdown station will call the desired phone system extension. The phone on that extension can
then communicate with the door phone and activate doorstrikes as needed. Note: Only a single door phone may be used. Multiple
relay activation mode cannot be used with Viking door phone models E-30 or any 1600A Series phone.
Inhibit Latching Commands Mode (✱6): In some installations it is critical that the door strike or door actuator not be turned on for
long periods of time. To prevent this from happening, enter ✱6 when in programming. In this mode, the toggle command (✱#) and
the continuous activation command (✱1) are ignored.
O
O
p
p
e
e
r
r
a
a
t
t
i
i
o
o
n
n
A. Doorbox Controller
A visitor pressing the “Call” button will cause the phones connected to the “LINE OUT TO PHONES“ terminals to ring. Simply
answer your phone to converse with the visitor. After answering the call, a single or double beep will be heard in the phone,
indicating which doorbox has called - a single beep for doorbox 1 and a double beep for doorbox 2.
1. Communicating with the Doorbox
a. Visitor Initiated Call
A doorbox may be monitored from any phone connected to the C-1000B by Touch Tone dialing a “#” followed by a Touch
Tone “1” or “2” to monitor doorbox 1 or doorbox 2 respectively. This feature is not available for pulse dialing phones. Note:
Do not attempt doorbox monitoring while a call is in progress, the call will be disconnected. Note: When monitoring, the
auxiliary contact will only work on the Continuous Mode (11).
b. Monitoring Doorboxes
(7)
If a C.O. line call is in progress and a doorbox is activated, a single or double “call waiting” tone will be heard indicating doorbox
1 or doorbox 2 is calling. To place the in-progress call on hold and answer the calling doorbox, simply dial a Touch Tone “#”,
pulse dial a “2” or hook flash twice.
2. Placing C.O. Line Calls on Hold
To activate a relay contact, you must be communicating with a doorbox. Simply Touch Tone dial “✱✱”, pulse dial a “3” or hook
flash three times. Two confirmation tones will be heard and the relay will be activated for the programmed doorstrike activation
time. The phone will then be returned to the C.O. line. If a call was in progress, the original caller will be taken off hold to con-
tinue the conversation. To return to the original call without activating a relay, Touch Tone dial “#”, pulse dial a “2” or hook flash
twice.
3. Activating a Doorstrike, Magnetic Lock or Gate Controller