Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at 301/451 Series Built-In Dishwashers vikingrange.
Table of Contents IMPORTANT– Please Read and Follow Warnings & Important Information _____________________________________________________3 Dimensions & Cutout Dimensions _____________________________________________________6 Specifications _______________________________________________________________________7 Custom Door Panel Specifications _____________________________________________________8 Custom Door Panel Installation Option _________________________________________________9 General Information
IMPORTANT–Please Read and Follow! WARNING WARNING ELECTRICAL SHOCK HAZARD Disconnect the electrical power supply and place a tag at the disconnect switch indicating that you are working on the circuit. • Electrically ground dishwasher. • Connect ground wire to green ground connector in terminal box. • DO NOT use an extension cord. • Failure to follow these instructions, can result in death, fire or electrical shock.
Dimensions & Cutout Dimensions Specifications Built-In Dishwasher 23 Description (60-7/8 .6 ” cm ) ” 24 cm) .0 (61 2 (61 4” .0 cm ) Overall height from floor Overall depth from rear ” /8 -7 ) 33.0 cm (86 Note: A 2” (5.1 cm) cut-out is required for water supply and discharge lines. cm 35 to ) ” (89 mi .0 n. cm ) (73 .0 451 Models 23-7/8” (60.6 cm) 33-7/8” (86.0 cm) min. to 35” (89.0 cm) max. Cutout width To edge of side – 23-5/8” (60.0 cm) – includes door panel With door open – 49” (124.
Custom Door Panel Custom Door Panel (Specifications for FDB451 Models) (Installation Option) Have the overlay panel constructed per dimensions. The panel thickness MAY NOT exceed 3/4" (1.91 cm) for flush installation in most cabinets. Ensure that the design, construction, and installation of the panel overlay and its handle mounting is sufficient to reliably operate in this application with a maximum panel weight of 18 lbs. (8.2 kg.) Custom panels should not exceed 18 lbs. (8.2 kg.
Custom Door Panel 5 (Installation Option, cont.) Verify operation of the door counter balance springs after installation of the overlay panel. The additional weight of the overlay panel might require an adjustment to the preload of the counterbalance springs. If adjustment of the springs is required, please refer to the “Counter Balance Spring” section.
Hardwire Conduit Option Electrical Connections Grounding Instructions WARNING Disconnect the electrical power supply and place a tag at the disconnect switch indicating that you are working on the circuit. 2 1 4. Care should be exercised, when the appliance is installed or removed to reduce the likelihood of damage to the power supply cord. • The dishwasher comes with a 3’9” (1.1 m) electrical cord for 110-120 volts, 15/20 amp supply.
Hardwire Conduit Option (301 Models, cont.) Green (Ground) 7 Hardwire Conduit Option 8 2 (451 Models, cont.) 5 1 6 White (Neutral) 2 1 1 3 3 Connect ground wire. Tighten screws on strain relief. Note: Reinstall front plate. Hardwire Conduit Option 1 4 x4 1 Run wire through grommet on bottom pan. Replace bottom pan. 2 Black (Line) Attach UL approved 3/4” strain relief (not included) to bottom of terminal box. Run wires through strain relief. 2 Connect wires to terminal block.
Trim Installation Options (451 Models) Counter Balance Spring Adjustment 1 1a (if necessary) 2 1 1 2 2 Dishwasher ships with trim installed for flush install. If needed, attach wiper gasket to dishwasher by pulling protective film off adhesive back. Apply behind hemmed edge of side trim. Remove spring from dishwasher. Disconnect cable from hook. 1b 2b 2 3 Increase tension 4 Decrease tension 1 2 2 x6 1 To install dishwasher without trim, remove the 6 screws (3 per side) and remove trim.
Installation Installation 6 2 1 (cont.) 1 2 2 1 4 2 x4 1 2 3 Carefully lay dishwasher on its back and attach the kick plate brackets. Screws for the brackets will already be in the base. Note: Be careful not to pinch hoses or power cord beneath dishwasher. To adjust the depth of the kick plate, loosen screws on the bracket and position in the required depth. Tighten screws and repeat for other side.
Final Installation Final Installation 9a 1 9b x4 12c x2 (cont.) 12d Air Gap Air Gap x2 2 3 For installation with trim (451 model), secure dishwasher by attaching provided mounting plugs and wood screws through trim panels into cabinets. Attach screws through top brackets into cabinets. (Discharge with air gap) For installation without trim (301 model), secure dishwasher by attaching screws through top brackets into cabinets. Note: DO NOT use mounting plugs.
Performance Checklist Service & Registration Testing for Leaks Unit Reset A qualified installer should carry out the following checks: • If the unit should need to be reset for any reason, push and hold the “START” button for 4 seconds. Only authorized replacement parts may be used in performing service on the appliance. Do not repair or replace any part of the appliance unless specifically recommended in the manual. All servicing should be referred to a qualified technician.