Instruction manual

© 2013 Directed. All rights Reserved. 1
Quick Reference Install Guide
Responder LCD, LED & 1-way systems
+ -
LIGHT FLASH POLARITY
(10A (MAXIMUM) FUSE JUMPER)
+ -
Bitwriter
Port
D2D Port (for external
Xpresskit interface module)
Detail
Optional Mux Port
(GWA Zone 4)
Optional Mux Port
(Zone 7)
10A FUSE
MINI ATM
RPN: 8540
10A FUSE
MINI ATM
RPN: 8540
Control Center
RF Port
for IVU
Door Lock
Harness
Auxiliary Harness
Main HarnessStarter Kill Harness
Wiring Connections
Main Harness, 12-pin connector
1 RED/WHITE (-) 200mA TRUNK RELEASE OUTPUT
2 RED (+)12VDC CONSTANT INPUT
3 BROWN (+) SIREN OUTPUT
4 WHITE/BROWN PARKING LIGHT ISOLATION WIRE - PIN 87a of onboard relay
5 BLACK (-) CHASSIS GROUND
6 VIOLET (+) DOOR TRIGGER INPUT
7 BLUE (-) TRUNK PIN/ INSTANT TRIGGER INPUT (N/C OR N/O)
8 GREEN (-) DOOR TRIGGER INPUT (N/C OR N/O)
9 BLACK/WHITE FLEX RELAY OUTPUT
10 WHITE/BLUE (-) 200mA AUX 1 OUTPUT
11 WHITE PARKING LIGHT OUTPUT
12 ORANGE (-) 500mA GROUND WHEN ARMED OUTPUT
Important: NEVER connect 200mA low current outputs directly to a motor or high
current device WITHOUT a relay
Auxiliary Harness, 7-pin connector
1 ORANGE/BLACK (-) 200mA AUX 4 OUTPUT
2 WHITE/BLACK (-) 200mA AUX 3 OUTPUT
3 VIOLET/BLACK (-) 200mA AUX 2 OUTPUT
4 LIGHT GREEN/BLACK (-) 200mA FACTORY ALARM DISARM OUTPUT
5 YELLOW (+) IGNITION INPUT
6 BROWN (-) 200mA HORN HONK OUTPUT
7 GREY N/O or N/C (-) HOOD PIN SWITCH INPUT
Door Lock Harness, 8-pin connector
1 VIOLET UNLOCK #87 NORMALLY OPEN (INPUT)
2 BLUE/BLACK UNLOCK #30 COMMON (OUTPUT)
3 BROWN/BLACK UNLOCK #87a NORMALLY CLOSED
4 VIOLET/BLACK LOCK #87 NORMALLY OPEN (INPUT)
5 GREEN/BLACK LOCK #30 COMMON (OUTPUT)
6 WHITE/BLACK LOCK #87a NORMALLY CLOSED
7 WHITE/VIOLET FLEX RELAY #87 NORMALLY OPEN (INPUT)
8 WHITE/BROWN FLEX RELAY #87a NORMALLY CLOSED
Starter Kill Harness, 3-pin connector
1 GREEN/WHITE STARTER - COMMON (KEY SIDE)
2 GREEN STARTER - NORMALLY OPEN (MOTOR SIDE)
3 GREEN/BLACK STARTER - NORMALLY CLOSED (MOTOR SIDE)
Installation Points
Adjusting the Shock Sensor
Adjusting with the LE (2-way ) or companion (1-way) remote control:
1. Make sure the ignition is off, and the system is disarmed with all open zones
closed.
2. Press and hold the
button of the remote control for 8 seconds until the trans-
mit LED turns on and then release it (If programmed to operate two systems,
ignore the transmit LED flashes at 3 seconds).
3. Press and hold the
button until the transmit LED flashes off then on and the
siren emits a long chirp. Adjustment mode is ready.
4. Adjust the sensitivity:
• Press and release the
button to increase the sensitivity. The siren chirps
two times.
• Press and release the
button to decrease the sensitivity. The siren
chirps one time.
• Press and release the
button to reset sensitivity to default setting. The
siren chirps three times.
Note: The remote control may or may not emit sounds during this operation.
Adjusting with the LCD remote control:
1. Make sure the ignition is off, and the system is disarmed with all open zones
closed.
2. Press and hold the
button of the remote control until a long beep is emit-
ted and
Main Menu
is displayed. (if programmed to operate two systems,
ignore the car 1 or car 2 text and beeps at 3 seconds).
3. Release the
button to view the main menu.
Setup Remote
is displayed.
4. Press and release the
button.
Sensor Adjust
is displayed.
5. Press and hold the
button until a long beep is emitted and the siren emits
a long chirp. The current sensitivity
Sen ##
is displayed, adjustment mode
is ready.
6. Adjust the sensitivity:
a. Press and release the
AUX
and buttons change the sensitivity.
b. Press and hold the
button. The adjustment is sent to the system and the
remote control emits a long beep as confirmation.
c. Release the button.
Note: After each adjustment the sensitivity can be tested by cautiously impacting
the vehicle with increasing intensity. The siren will chirp to indicate the impact level
required to fully trigger the alarm.
Exit adjustment mode:
• Press and release the
button any time to exit adjustment mode, and then
press and hold to return the remote control to normal operation (transmit LED
turns off).
• Open the hood or trunk
• Tu rn the ignition on
• Wait for 30 seconds between steps
The siren will emit one long chirp when exiting adjustment mode.
Long Term Event History
The system stores the last six full triggers in memory. These are not erasable. To ac-
cess long term event history:
1. With the ignition off, press and hold the control center button.
2. Turn the ignition on.
3. Release the control center button.
4. Within 5 seconds, press and release the control center button. The control cen-
ter LED flashes in groups indicating the last six zones that triggered the unit for
1 minute or until the ignition is turned off (indicated in the order of most recent
first to oldest last). Refer to Table of Zones.
Note: The Warn Away triggers are not stored to memory and is not reported.
Table of Zones
A zone is represented by the number of control center LED flashes used by
the system to identify a particular type of input.
Zone Description Input Description
1 Trunk Pin H1/7 Blue wire
2 Instant trigger: a heavier impact
detected by the onboard shock sensor
On board shock sensor.
3 Door switch trigger H1/8 Green or H1/6 Violet wire
4 Instant trigger: For optional sensors 3 pin optional GWA MUX port
5 Ignition trigger H3/5 Yellow wire
6 Hood Pin H3/7 Grey wire
7 Instant trigger: For optional sensors 4 pin optional MUX port
Basic Remote Functions
Button
Level
Direct Access
x 1
LEVEL 1
x 2
LEVEL 2
x 3
LEVEL 3
x 4
LEVEL 4
Arm/Lock
(Panic)
Silent Arm Sensor
Bypass
Sensor Silent
Arm
Full Silent
Arm
Disarm/Unlock Silent Disarm Remote Valet Car Finder
Remote Start*/
Aux 1/4**
A U X
Aux/Trunk AUX 1 AUX 2 AUX 3 AUX 4
Advance Level
Change Car
(3s), Enter
programming
(8s)
Arm Status
(2-way only)
* Available only with optional Remote Start module installation
** This button can command either Aux 1 or Aux 4 if turned on by an
authorized Directed dealer.
Important: If the IVU (control center) has been replaced, all remote controls
must be re-paired with the system. See Remote Pairing for details.
See full Installation Guide for more
detailed information. Such informa-
tion and more can be found online
at: www.directechs.com
Bitwriters with a date code of 6a or older require an
IC upgrade (p/n 998M). Some bitwriters with a date
code of 6B do not require the IC upgrade, refer to tech
tip # 1112 for more information.
The Bitwriter® (p/n 998U)
requires chip version 2.7 or
newer to program this unit.
GWA Mux Harness, 3-pin connector
1 RED +12 VDC TO SENSOR
2 BLACK GND TO SENSOR
3 BLUE/WHITE MUX WIRE INPUT
Guide Translations
For a Spanish or French version of the Installation Guide, please download it from
www.directechs.com under “Resources”.
Traducción de los manuales:
Para obtener una versión en Español o Francés del Manual de Instalación, descár-
guela de www.directechs.com bajo el título “Recursos” (“Resources”).
Traduction du guide:
Pour une version française ou espagnole du guide d’installation, veuillez le té-
lécharger à www.directechs.com sous «Resources»..