Datasheet

ManualsBrandsVishay ManualsCapacitorsSolid Tantalum Capacitor, 47uF, 50V, 20%

597D

www.vishay.com

Vishay Sprague

Revision: 01-Apr-2019

Document Number: 40047

For technical questions, contact: tantalum@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Solid Tantalum Chip Capacitors, TANTAMOUNT™,

Ultra-Low ESR, Conformal Coated, Maximum CV

PERFORMANCE CHARACTERISTICS

www.vishay.com/doc?40194

Operating Temperature: -55 °C to +125 °C

(above 85 °C, voltage derating is required)

Capacitance Range: 10 μF to 2200 μF

Capacitance Tolerance: ± 10 %, ± 20 % standard

Voltage Rating: 4 V

to 75 V

Moisture Sensitivity Level 2a

FEATURES

• New case size offerings

• Terminations: 100 % tin (2) standard; tin / lead

available

• Extremely low ESR

• Mounting: surface mount

• Ripple current up to 4.1 A

• Material categorization: for definitions of compliance

please see www.vishay.com/doc?99912

Note

This datasheet provides information about parts that are



RoHS-compliant and / or parts that are non RoHS-compliant. For



example, parts with lead (Pb) terminations are not RoHS-compliant.



Please see the information / tables in this datasheet for details

Note

• Preferred tolerance and reel sizes are in bold.

We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. 

Low ESR solid tantalum chip capacitors allow delta ESR of 1.25 times the datasheet limits after mounting

Note

• The anode termination (D less B) will be a minimum of 0.012" [0.3 mm]

Available

ORDERING INFORMATION

597D 687 X0 6R3 E 2 T

TYPE CAPACITANCE CAPACITANCE

TOLERANCE

DC VOLTAGE RATING

AT +85 °C

CASE CODE TERMINATION REEL SIZE AND

PACKAGING

This is expressed in pF.

The first two digits are

the significant figures.

The third is the number

of zeros to follow.

X0 = ± 20 %

X9 = ± 10 %

This is expressed in V.

To complete the three-digit

block, zeros precede the

voltage rating. A decimal

point is indicated by an “R”

(6R3 = 6.3 V).

See Ratings

and Case

Codes table

2 = 100 % tin

8 = solder plated

(60/40)

special order

T = tape and reel

7" [178 mm] reel

DIMENSIONS in inches [millimeters]

CASE CODE L (MAX.) W H A B D (REF.) J (MAX.)

0.299

[7.6]

0.173 ± 0.016

[4.4 ± 0.4]

0.079

[2.0 max.]

0.051 ± 0.012

[1.3 ± 0.3]

0.181 ± 0.024

[4.6 ± 0.6]

0.252

[6.4]

0.004

[0.1]

0.299

[7.6]

0.173 ± 0.016

[4.4 ± 0.4]

0.138

[3.5 max.]

0.051 ± 0.012

[1.3 ± 0.3]

0.181 ± 0.024

[4.6 ± 0.6]

0.252

[6.4]

0.004

[0.1]

0.299

[7.6]

0.173 ± 0.016

[4.4 ± 0.4]

0.157 ± 0.016

[4.0 ± 0.4]

0.051 ± 0.012

[1.3 ± 0.3]

0.181 ± 0.024

[4.6 ± 0.6]

0.252

[6.4]

0.004

[0.1]

0.299

[7.6]

0.238 ± 0.016

[6.0 ± 0.4]

0.142 ± 0.016

[3.6 ± 0.4]

0.051 ± 0.012

[1.3 ± 0.3]

0.181 ± 0.024

[4.6 ± 0.6]

0.244

[6.2]

0.004

[0.1]

0.299

[7.6]

0.238 ± 0.016

[6.0 ± 0.4]

0.185 ± 0.016

[4.7 ± 0.4]

0.055 ± 0.016

[1.4 ± 0.4]

0.181 ± 0.024

[4.6 ± 0.6]

0.244

[6.2]

0.004

[0.1]

0.299

[7.6]

0.238 ± 0.016

[6.0 ± 0.4]

0.236 ± 0.016

[6.0 ± 0.4]

0.055 ± 0.016

[1.4 ± 0.4]

0.181 ± 0.024

[4.6 ± 0.6]

0.244

[6.2]

0.004

[0.1]

0.315

[8.0]

0.260 + 0.016 / - 0.024

[6.6 + 0.4 / - 0.6]

0.142 ± 0.016

[3.6 ± 0.4]

0.051 ± 0.012

[1.3 ± 0.3]

0.197 ± 0.024

[5.0 ± 0.6]

0.260

[6.6]

0.004

[0.1]

0.315

[8.0]

0.260 + 0.016 / - 0.024

[6.6 + 0.4 / - 0.6]

0.205 ± 0.016

[5.2 ± 0.4]

0.055 ± 0.016

[1.4 ± 0.4]

0.197 ± 0.024

[5.0 ± 0.6]

0.260

[6.6]

0.004

[0.1]

Tantalum wire

nib identies

anode (+)

terminal

Summary of content (20 pages)

PAGE 1
597D www.vishay.com Vishay Sprague Solid Tantalum Chip Capacitors, TANTAMOUNT™, Ultra-Low ESR, Conformal Coated, Maximum CV FEATURES • New case size offerings • Terminations: 100 % tin (2) standard; tin / lead available Available • Extremely low ESR Available • Mounting: surface mount • Ripple current up to 4.1 A PERFORMANCE CHARACTERISTICS • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 www.vishay.
PAGE 2
597D www.vishay.com Vishay Sprague RATINGS AND CASE CODES μF 4V 6.3 V 10 V 16 V 20 V 25 V 35 V 40 V 50 V 10 63 V 75 V D R 15 E/R R R/F 22 R F Z/H F Z 33 47 R Z 68 R F 100 F F/H 150 F 220 330 E R V E F H 470 V E E H H 680 E E R H 1000 E/R R F 1500 R F 2200 R H M STANDARD RATINGS CAPACITANCE (μF) CASE CODE PART NUMBER 470 V 597D477(1)004V(2)(3) MAX. DF AT +25 °C 120 Hz (%) MAX. ESR AT +25 °C 100 kHz (m) MAX.
PAGE 3
597D www.vishay.com Vishay Sprague STANDARD RATINGS MAX. DF AT +25 °C 120 Hz (%) MAX. ESR AT +25 °C 100 kHz (m) MAX. RIPPLE 100 kHz IRMS (A) 44 8 80 1.8 597D337(1)020H(2)(3) 66 10 100 1.6 597D477(1)020H(2)(3) 94 14 100 1.6 17 6 100 1.6 597D107(1)025F(2)(3) 25 8 100 1.6 597D157(1)025F(2)(3) 38 8 80 1.8 597D227(1)025M(2)(3) 55 8 100 1.
PAGE 4
597D www.vishay.com Vishay Sprague TYPICAL CURVES ESR AND Z VS. FREQUENCY 1500 μF - 4 V, Case Size “R” 330 μF - 10 V, Case Size “E” 1 1000 Z 0.1 100 ESR 10 1000 0.01 1 10 100 1000 Z 0.1 100 ESR 0.01 0.1 1 10 Frequency (kHz) 1000 μF - 6.3 V, Case Size “R” 1 1000 1 2nd line Impedance / ESR (Ω) 10000 1st line 2nd line 2nd line Impedance / ESR (Ω) 330 μF - 6.3 V, Case Size “V” Z 100 0.1 ESR 10 1000 0.01 1 10 10 1000 Frequency (kHz) 10 0.
PAGE 5
97D www.vishay.com Vishay Sprague POWER DISSIPATION CASE CODE MAXIMUM PERMISSIBLE POWER DISSIPATION AT +25 °C (W) IN FREE AIR V 0.141 D 0.215 E 0.240 R, F, M 0.250 Z 0.265 H 0.265 STANDARD PACKAGING QUANTITY CASE CODE UNITS PER 7" REEL V 1000 D 400 E 500 R 300 F 250 Z 250 M 200 H 200 PRODUCT INFORMATION Conformal Coated Guide Pad Dimensions www.vishay.com/doc?40150 Packaging Dimensions Moisture Sensitivity (MSL) www.vishay.
PAGE 6
Conformal Coated Guide www.vishay.com Vishay Sprague Guide for Conformal Coated Tantalum Capacitors INTRODUCTION Tantalum electrolytic capacitors are the preferred choice in applications where volumetric efficiency, stable electrical parameters, high reliability, and long service life are primary considerations.
PAGE 7
Conformal Coated Guide www.vishay.com SOLID ELECTROLYTE TANTALUM CAPACITORS Solid electrolyte capacitors contain manganese dioxide, which is formed on the tantalum pentoxide dielectric layer by impregnating the pellet with a solution of manganous nitrate. The pellet is then heated in an oven, and the manganous nitrate is converted to manganese dioxide.
PAGE 8
Conformal Coated Guide www.vishay.
PAGE 9
Conformal Coated Guide www.vishay.
PAGE 10
Conformal Coated Guide www.vishay.com Vishay Sprague TAPE AND REEL PACKAGING in inches [millimeters] 0.157 ± 0.004 [4.0 ± 0.10] T2 (max.) Deformation between embossments 0.024 [0.600] max. 0.059 + 0.004 - 0.0 [1.5 + 0.10 - 0.0] Top cover tape A0 K0 B1 (max.) (6) Top cover tape For tape feeder reference only including draft. Concentric around B0 0.004 [0.10] max. 10 pitches cumulative tolerance on tape ± 0.008 [0.200] Embossment 0.079 ± 0.002 0.069 ± 0.004 [2.0 ± 0.05] [1.75 ± 0.10] 0.030 [0.
PAGE 11
Conformal Coated Guide www.vishay.com Vishay Sprague CARRIER TAPE DIMENSIONS in inches [millimeters] TAPE WIDTH W D0 8 mm 0.315 + 0.012 / - 0.004 [8.0 + 0.3 / - 0.1] 12 mm 0.479 + 0.012 / - 0.004 [12.0 + 0.3 / - 0.1] 16 mm 0.635 + 0.012 / - 0.004 [16.0 + 0.3 / - 0.1] 24 mm 0.945 ± 0.012 [24.0 ± 0.3] P2 F 0.078 ± 0.0019 [2.0 ± 0.05] 0.059 + 0.004 / - 0 [1.5 + 0.1 / - 0] E1 0.14 ± 0.0019 [3.5 ± 0.05] 0.216 ± 0.0019 [5.5 ± 0.05] 0.078 ± 0.004 [2.0 ± 0.1] E2 min. 0.246 [6.25] 0.324 ± 0.
PAGE 12
Conformal Coated Guide www.vishay.
PAGE 13
Conformal Coated Guide www.vishay.com Vishay Sprague PAD DIMENSIONS in inches [millimeters] B C B A CASE CODE WIDTH (A) PAD METALLIZATION (B) SEPARATION (C) 592D / W - 591D A 0.075 [1.9] 0.050 [1.3] 0.050 [1.3] B 0.118 [3.0] 0.059 [1.5] 0.059 [1.5] C 0.136 [3.5] 0.090 [2.3] 0.122 [3.1] D 0.180 [4.6] 0.090 [2.3] 0.134 [3.4] M 0.256 [6.5] R 0.240 [6.1] Anode pad: 0.095 [2.4] Cathode pad: 0.067 [1.7] Anode pad: 0.095 [2.4] Cathode pad: 0.067 [1.7] 0.138 [3.5] 0.118 [3.0] S 0.
PAGE 14
Conformal Coated Guide www.vishay.com Vishay Sprague PAD DIMENSIONS in inches [millimeters] B C B A CASE CODE WIDTH (A) PAD METALLIZATION (B) SEPARATION (C) 0.50 [1.3] 0.70 [1.8] 0.70 [1.8] 0.70 [1.8] 0.70 [1.8] 0.70 [1.8] 0.70 [1.8] 0.90 [2.3] 0.040 [1.0] 0.055 [1.4] 0.120 [3.0] 0.070 [1.8] 0.120 [3.0] 0.140 [3.6] 0.170 [4.3] 0.170 [4.3] 0.059 [1.5] 0.090 [2.3] 0.090 [2.3] 0.090 [2.3] 0.040 [1.02] 0.040 [1.02] 0.065 [1.65] 0.059 [1.5] 0.120 [3.1] 0.136 [3.47] 0.140 [3.6] 0.040 [1.02] 0.040 [1.
PAGE 15
Conformal Coated Guide www.vishay.com Vishay Sprague RECOMMENDED REFLOW PROFILES Capacitors should withstand reflow profile as per J-STD-020 standard, three cycles. TEMPERATURE (°C) Tp tp Max. ramp-up rate = 3 °C/s Max. ramp-down rate = 6 °C/s TL Ts max. TC - 5 °C tL Preheat area Ts min. ts 25 Time 25 °C to peak TIME (s) PROFILE FEATURE SnPb EUTECTIC ASSEMBLY LEAD (Pb)-FREE ASSEMBLY Temperature min. (Ts min.) 100 °C 150 °C Temperature max. (Ts max.
PAGE 16
Conformal Coated Guide www.vishay.com Vishay Sprague GUIDE TO APPLICATION 1. AC Ripple Current: the maximum allowable ripple current shall be determined from the formula: I R MS = 5. Power Dissipation: power dissipation will be affected by the heat sinking capability of the mounting surface. Non-sinusoidal ripple current may produce heating effects which differ from those shown. It is important that the equivalent IRMS value be established when calculating permissible operating levels.
PAGE 17
Typical Performance Characteristics www.vishay.com Vishay Sprague Conformal Coated Tantalum Capacitors ELECTRICAL PERFORMANCE CHARACTERISTICS ITEM PERFORMANCE CHARACTERISTICS Category temperature range -55 °C to +85 °C (to +125 °C with voltage derating) Capacitance tolerance ± 20 %, ± 10 %, tested via bridge method, at 25 °C, 120 Hz Dissipation factor Limits per Standard Ratings table. Tested via bridge method, at 25 °C, 120 Hz ESR Limits per Standard Ratings table.
PAGE 18
Typical Performance Characteristics www.vishay.com Vishay Sprague TYPICAL LEAKAGE CURRENT TEMPERATURE FACTOR 100 Leakage Current Factor +125 °C 10 +85 °C +55 °C +25 °C 1.0 0 °C 0.1 -55 °C 0.01 0.
PAGE 19
Typical Performance Characteristics www.vishay.com Vishay Sprague MECHANICAL PERFORMANCE CHARACTERISTICS ITEM CONDITION POST TEST PERFORMANCE Terminal strength / Shear force test Apply a pressure load of 5 N for 10 s ± 1 s horizontally to the center of capacitor side body AEC-Q200-006 Capacitance change Dissipation factor Leakage current Within ± 10 % of initial value Initial specified limit Initial specified limit There shall be no mechanical or visual damage to capacitors post-conditioning.
PAGE 20
Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product.