Datasheet

ManualsBrandsVishay ManualsChip SMD ResistorsSMD Resistor, 0207, 10Ohm

CMB 0207

www.vishay.com

Vishay Beyschlag

Revision: 11-Feb-16

Document Number: 28755

For technical questions, contact: melf@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TEST PROCEDURES AND REQUIREMENTS

60 115-1

CLAUSE

IEC

60 068-2

(1)

TEST

METHOD

TEST PROCEDURE

REQUIREMENTS

PERMISSIBLE CHANGE (R)

Stability for product types:

CMB 0207 2.2  to 1.5 M

4.5 - Resistance - ± 5 % R; ± 2 % R; ± 1 % R

4.8 - Temperature coefficient

At (20 / -55 / 20) °C

and (20 / 125 / 20) °C

see Temperature Coefficient graph

4.25.1

Endurance at 70 °C:

standard operation mode

U = U

max.

;

whichever is the less severe;

1.5 h on; 0.5 h off;

70 °C; 1000 h ± (1 % R + 0.05)

70 C; 8000 h ± (2 % R + 0.05)

Endurance at 70 C:

power operation mode

U = U

max.

;

whichever is the less severe;

1.5 h on; 0.5 h off;

70 °C; 1000 h ± (2 % R + 0.05)

70 C; 8000 h ± (4 % R + 0.05)

4.25.3 -

Endurance at upper category

temperature

125 °C; 1000 h ± (2 % R + 0.05)

155 °C; 1000 h ± (4 % R + 0.05)

4.24 78 (Cab) Damp heat, steady state (40 ± 2C; 56 days; (93 ± 3) % RH ± (1 % R + 0.1 )

4.37 67 (Cy)

Damp heat,

steady state,

accelerated

(85 ± 2) °C

(85 ± 5) % RH

U =  100 V

and U = 0.3 x U

max.

;

(the smaller value is valid)

1000 h

± (2 % R + 0.1 )

4.23 Climatic sequence:

4.23.2 2 (Ba) dry heat UCT; 16 h

4.23.3 30 (Db) damp heat, cyclic 55 C; 24 h; 90 % RH; 1 cycle

4.23.4 1 (Aa) cold LCT; 2 h

4.23.5 13 (M) low air pressure 8.5 kPa; 2 h; (25 ± 10) C

4.23.6 30 (Db) damp heat, cyclic 55 C; 24 h; 90 % RH; 5 cycles

4.23.7 - DC load U = U

max.

; 1 min

LCT = -55 C; UCT = 155 °C ± (1 % R + 0.1 )

- 1 (Aa) Cold -55 C; 2 h ± (0.5 % R + 0.1)

4.19 14 (Na) Rapid change of temperature

30 min at LCT;

30 min at UCT;

LCT = -55 °C; UCT = 125 °C

5 cycles ± (0.5 % R + 0.1 )

1000 cycles ± (1.5 % R + 0.1 )

4.13 -

Short time overload;

standard operation mode

U = 2.5 x  2 x U

max.

;

whichever is the less severe;

5 s

± (0.25 % R + 0.1 )

Short time overload;

power operation mode

U = 2.5 x  2 x U

max.

;

whichever is the less severe;

5 s

± (0.5 % R + 0.1 )

4.22 6 (Fc) Vibration

Endurance by sweeping;

10 Hz to 2000 Hz;

no resonance;

amplitude  1.5 mm or

200 m/s

; 7.5 h

± (0.25 % R + 0.1)

x R

0.3 x P

x R