Datasheet

ManualsBrandsVishay ManualsChip SMD ResistorsAEC-Q200 Pulse Proof Thick Film Chip Resistor 2.2Ohm ±5% 1206

D/CRCW-IF e3

www.vishay.com

Vishay

Revision: 17-Mar-15

Document Number: 20024

For technical questions, contact: thickfilmchip@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Pulse Proof Thick Film Chip Resistors

FEATURES

• High pulse performance, up to 10 kW

• Stability R/R  1 % for 1000 h at 70 °C

• AEC-Q200 qualified

• Material categorization: for definitions of

compliance please see www.vishay.com/doc?99912

Notes

• These resistors do not feature a limited lifetime when operated within the limits of rated dissipation, permissible operating voltage, and

permissible film temperature. However, the resistance typically increase due to the resistor’s film temperature over operating time, generally

known as drift. The drift may exceed the stability requirements of an individual application circuit and thereby limits the functional time.

• Marking: See data sheet “Surface Mount Resistor Marking” (document number 20020).

• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.

Note

(1)

The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the

printe-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.

STANDARD ELECTRICAL SPECIFICATIONS

TYPE

CASE

SIZE

IMPERIAL

CASE

SIZE

METRIC

POWER

RATING

LIMITING

ELEMENT

VOLTAGE

max.

RMS

/DC

TEMPERATURE

COEFFICIENT

ppm/K

TOLERANCE

RESISTANCE

RANGE



SERIES

D10/CRCW0402-IF 0402 RR1005M 0.063 50 ± 200

± 5

1.0 to 100K E24

± 10

D11/CRCW0603-IF 0603 RR1608M 0.10 75 ± 200

± 5

1.0 to 100K E24

± 10

D12/CRCW0805-IF 0805 RR2012M 0.125 150 ± 200

± 5

1.0 to 100K E24

± 10

D25/CRCW1206-IF 1206 RR3216M 0.25 200 ± 200

± 5

1.0 to 100K E24

± 10

CRCW1210-IF 1210 RR3225M 0.50 200 ± 200

± 5

1.0 to 100K E24

± 10

CRCW2010-IF 2010 RR5025M 0.75 400 ± 200

± 5

1.0 to 100K E24

± 10

CRCW2512-IF 2512 RR6332M 1.0 500 ± 200

± 5

1.0 to 100K E24

± 10

TECHNICAL SPECIFICATIONS

PARAMETER UNIT

D10/

CRCW0402-IF

D11/

CRCW0603-IF

D12/

CRCW0805-IF

D25/

CRCW1206-IF

CRCW1210-IF CRCW2010-IF CRCW2512-IF

Rated dissipation



(1)

W 0.063 0.1 0.125 0.25 0.5 0.75 1.0

Operating voltage



max.

RMS

/DC

V 50 75 150 200 200 400 500

Insulation voltage



ins

(1 min)

V 75 100 200 300 300 300 300

Insulation resistance



> 10

Operating temperature



range

°C -55 to +155

Failure rate h

-1

< 0.1 x 10

-9

Mass mg 0.65 2 5.5 10 16 25.5 40.5

Summary of content (8 pages)

PAGE 1
D/CRCW-IF e3 www.vishay.com Vishay Pulse Proof Thick Film Chip Resistors FEATURES • High pulse performance, up to 10 kW • Stability R/R  1 % for 1000 h at 70 °C • AEC-Q200 qualified • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 STANDARD ELECTRICAL SPECIFICATIONS LIMITING ELEMENT VOLTAGE Umax. ACRMS/DC V TEMPERATURE COEFFICIENT ppm/K CASE SIZE IMPERIAL CASE SIZE METRIC POWER RATING P70 W D10/CRCW0402-IF 0402 RR1005M 0.
PAGE 2
D/CRCW-IF e3 www.vishay.
PAGE 3
D/CRCW-IF e3 www.vishay.com Vishay DIMENSIONS in millimeters L T2 b I W a H T1 SIZE RECOMMENDED SOLDER PAD DIMENSIONS DIMENSIONS T1 WAVE SOLDERING IMPERIAL METRIC L W T2 a b l 0402 RR1005M 1.0 ± 0.05 0.5 ± 0.05 0.35 ± 0.05 0.25 ± 0.05 0.2 ± 0.1 0.4 0.6 0.5 0603 RR1608M 1.55 0.85 ± 0.1 0.45 ± 0.05 0.3 ± 0.2 0.5 0.9 0.3 ± 0.2 0.7 + 0.10 - 0.05 H REFLOW SOLDERING 0.3 ± 0.2 + 0.20 - 0.10 a b l 1.0 0.9 0.9 1.0 1.3 1.2 0.9 1.3 1.3 0805 RR2012M 2.0 + 0.
PAGE 4
D/CRCW-IF e3 www.vishay.com Vishay Pulse Power (W) Maximum pulse dissipation as a function of the pulse duration, continuous pulse loading 100 000 2512 2010 1210 1206 0805 0603 0402 10 000 1000 100 10 1 0.1 0.01 0.000001 0.00001 0.0001 0.001 0.01 0.1 1 10 100 Pulse Duration (s) Pulse Voltage Û max. (V) Maximum pulse load, continuous pulses; applicable if P ≤ P (ϑamb) and Û ≤ Ûmax.
PAGE 5
D/CRCW-IF e3 www.vishay.com Vishay Peak Voltage (V) Single-pulse high voltage overload test 1.2 µs/50 µs EN 140000 4.27 10 000 2512 2010 1210 1206 0805 0603 0402 1000 100 10 1 1 10 100 1000 10 000 100 000 Resistance Value (Ω) Pulse load rating in accordance to EN 60115-1, 4.27; 1.2 μs/50 μs; 5 pulses at 12 s intervals; for permissible resistance change 1 % Peak Voltage (V) Single-pulse high voltage overload test 10 µs/700 µs EN 140000 4.
PAGE 6
D/CRCW-IF e3 www.vishay.com Vishay Fraction of Rated Dissipation P70 (%) Derating 100 50 0 - 50 0 50 100 150 70 Ambient Temperature ϑamb (°C) TEST PROCEDURES AND REQUIREMENTS IEC EN 60082-2 60115-1 TEST CLAUSE METHOD PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R) STABILITY CLASS 1 OR BETTER TEST Stability for product type: D/CRCW-IF e3 1  to 100 k 4.5 - Resistance - ± 5 %; ± 10 % 4.7 - Voltage proof U = 1.4 x Uins; 60 s No flashover or breakdown 4.
PAGE 7
D/CRCW-IF e3 www.vishay.com Vishay TEST PROCEDURES AND REQUIREMENTS IEC EN 60082-2 60115-1 TEST CLAUSE METHOD PROCEDURE REQUIREMENTS PERMISSIBLE CHANGE (R) STABILITY CLASS 1 OR BETTER TEST Stability for product type: D/CRCW-IF e3 4.23 - Climatic sequence: - 4.23.2 2 (Ba) Dry heat 125 °C; 16 h 4.23.3 30 (Db) Damp heat, cyclic 55 °C;  90 % RH; 24 h; 1 cycle 4.23.4 1 (Aa) Cold - 55 °C; 2 h 4.23.5 13 (M) Low air pressure 1 kPa; (25 ± 10) °C; 1 h 4.23.
PAGE 8
Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product.