Datasheet

ManualsBrandsVishay ManualsChip SMD ResistorsSMD Resistor 400mW, 47kOhm, 1 %, 0204

MMU 0102, MMA 0204, MMB 0207 - Professional

www.vishay.com

Vishay Beyschlag

Revision: 09-Feb-16

Document Number: 28713

For technical questions, contact: melf@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Professional Thin Film MELF Resistors

MMU 0102, MMA 0204, and MMB 0207 professional thin

film MELF resistors are the perfect choice for most fields of

modern professional electronics where reliability and

stability is of major concern. The typical applications in the

fields of automotive, telecommunication and medical

equipment reflect the outstanding level of proven reliability.

FEATURES

• Approved according to EN 140401-803

• AEC-Q200 qualified

• Advanced metal film technology

• Excellent overall stability: exceeds class 0.25

• Best in class pulse load capability

• Intrinsic sulfur resistance

• Material categorization: 

for definitions of compliance please see

www.vishay.com/doc?99912

APPLICATIONS

• Automotive

• Telecommunication

• Industrial

• Medical equipment

Note

(1)

Please refer to APPLICATION INFORMATION below.

APPLICATION INFORMATION

When the resistor dissipates power, a temperature rise above the ambient temperature occurs, dependent on the thermal

resistance of the assembled resistor together with the printed circuit board. The rated dissipation applies only if the permitted

film temperature is not exceeded.

These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift

increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a

functional lifetime.

TECHNICAL SPECIFICATIONS

DESCRIPTION MMU 0102 MMA 0204 MMB 0207

DIN size 0102 0204 0207

Metric size code RC2211M RC3715M RC6123M

Resistance range 0.22  to 2.21 M; 0 0.22  to 10 M; 0 0.1  to 15 M; 0 

Resistance tolerance ±5 %; ± 2 %; ± 1 %; ± 0.5 % ±5 %; ± 1 %; ± 0.5 % ±5 %; ± 2 %; ± 1 %; ± 0.5 %

Temperature coefficient ± 50 ppm/K; ± 25 ppm/K

± 100 ppm/K; ± 50 ppm/K;

± 25 ppm/K

Rated dissipation, P

(1)

0.3 W 0.4 W 1.0 W

Operating voltage, U

max.

RMS

/DC 150 V 200 V 350 V

Permissible film temperature,



F max.

(1)

155 °C

Operating temperature range

(1)

-55 °C to 155 °C

Permissible voltage against ambient (insulation):

1 min, U

ins

200 V 300 V 500 V

Failure rate: FIT

observed

0.1 x 10

9

Summary of content (14 pages)

PAGE 1
MMU 0102, MMA 0204, MMB 0207 - Professional www.vishay.com Vishay Beyschlag Professional Thin Film MELF Resistors FEATURES • Approved according to EN 140401-803 • AEC-Q200 qualified • Advanced metal film technology • Excellent overall stability: exceeds class 0.25 • Best in class pulse load capability • Intrinsic sulfur resistance • Material categorization:  for definitions of compliance please see www.vishay.
PAGE 2
MMU 0102, MMA 0204, MMB 0207 - Professional www.vishay.com Vishay Beyschlag MAXIMUM RESISTANCE CHANGE AT RATED DISSIPATION OPERATION MODE Rated dissipation, P70 STANDARD POWER MMU 0102 0.2 W 0.3 W MMA 0204 0.25 W 0.4 W MMB 0207 0.4 W 1.0 W -55 °C to 125 °C -55 °C to 155 °C 125 °C 155 °C MMU 0102 0.22  to 221 k 0.22  to 221 k MMA 0204 0.22  to 332 k 0.22  to 332 k MMB 0207 0.1  to 1 M 0.1  to 1 M 1000 h 0.15 %  0.25 % 8000 h 0.3 %  0.5 % 225 000 h 1.
PAGE 3
MMU 0102, MMA 0204, MMB 0207 - Professional www.vishay.com Vishay Beyschlag PACKAGING TYPE/SIZE MMU 0102 MMA 0204 CODE QUANTITY PACKAGING STYLE WIDTH PITCH B3 = BL 3000 Antistatic blister tape acc. IEC 60286-3, Type 2a 8 mm 4 mm Bulk case acc. IEC 60286-6 - - Antistatic blister tape acc. IEC 60286-3, Type 2a 8 mm 4 mm Bulk case acc. IEC 60286-6 - - Antistatic blister tape acc.
PAGE 4
MMU 0102, MMA 0204, MMB 0207 - Professional www.vishay.com Vishay Beyschlag DESCRIPTION MATERIALS Production is strictly controlled and follows an extensive set of instructions established for reproducibility. A homogeneous film of metal alloy is deposited on a high grade ceramic body (Al2O3) and conditioned to achieve the desired temperature coefficient. Nickel plated steel termination caps are firmly pressed on the metallised rods.
PAGE 5
MMU 0102, MMA 0204, MMB 0207 - Professional www.vishay.com Vishay Beyschlag Power Dissipation P FUNCTIONAL PERFORMANCE 1 MMB 0207 MMA 0204 MMU 0102 W 0.5 0 - 50 0 50 70 C 100 150 Ambient Temperature ϑ amb Power Dissipation P Derating - Standard Operation Mode 1 MMB 0207 MMA 0204 MMU 0102 W 0.5 0 - 50 0 50 70 100 C 150 Ambient Temperature ϑ amb Pulse Load Pmax. Derating - Power Operation Mode MMB 0207 MMA 0204 MMU 0102 100 W 10 1 0.
PAGE 6
MMU 0102, MMA 0204, MMB 0207 - Professional Continuous Pulse Load Pmax. www.vishay.com Vishay Beyschlag MMB 0207 MMA 0204 MMU 0102 100 W 10 1 0.1 1 µs 10 µs 100 µs 1 ms 10 ms 100 ms 1s 10 s Pulse Duration ti Maximum pulse load, continuous pulse; applicable if P ≤ P (ϑamb) and U ≤ Umax.; for permissible resistance change ± (0.5 % R + 0.01 Ω) Pulse Load P Continuous Pulse for R < 10 Ω 1000 MMB 0207 MMA 0204 MMU 0102 W 100 10 1 0.
PAGE 7
MMU 0102, MMA 0204, MMB 0207 - Professional Pulse Voltage Umax. www.vishay.com Vishay Beyschlag MMB 0207 MMA 0204 MMU 0102 V 1000 100 1 µs 10 µs 100 µs 10 ms 1 ms 100 ms 1s 10 s Pulse Duration ti Maximum pulse voltage, single and continuous pulses; applicable if P ≤ Pmax.; for permissible resistance change ± (0.5 % R + 0.
PAGE 8
MMU 0102, MMA 0204, MMB 0207 - Professional Current Noise Voltage Ratio www.vishay.com Vishay Beyschlag 1 µV/V 0.1 MMB 0207 MMA 0204 MMU 0102 0.01 100 Ω 1 kΩ 10 kΩ 100 kΩ 1 MΩ 10 MΩ Resistance Value R In accordance with IEC 60195 IZI/R Current Noise Voltage Ratio 2.0 1.5 1.0 MMB 0207 MMA 0204 MMU 0102 0.5 0.1 0.3 1 GHz 3 Frequency f |Z|/R for 49.9 Ω MELF resistors RF - Behavior Revision: 09-Feb-16 Document Number: 28713 8 For technical questions, contact: melf@vishay.
PAGE 9
MMU 0102, MMA 0204, MMB 0207 - Professional www.vishay.com Vishay Beyschlag TESTS AND REQUIREMENTS All tests are carried out in accordance with the following specifications: EN 60115-1, generic specification EN 60115-8 (successor of EN 140400), sectional specification EN 140401-803, detail specification The testing also covers most of the requirements specified by EIA/ECA-703 and JIS-C-5201-1. The tests are carried out under standard atmospheric conditions in accordance with IEC 60068-1, 4.
PAGE 10
MMU 0102, MMA 0204, MMB 0207 - Professional www.vishay.com Vishay Beyschlag TEST PROCEDURES AND REQUIREMENTS IEC EN 60 068-2 (1) 60 115-1 TEST CLAUSE METHOD TEST Stability for product types: STABILITY CLASS 0.5 OR BETTER STABILITY CLASS 1 OR BETTER STABILITY CLASS 2 OR BETTER MMU 0102 10  to 221 k 1  to < 10  <1 > 221 k MMA 0204 10  to 332 k 1  to < 10  <1 > 332 k MMB 0207 10  to 1 M 1  to < 10  <1 > 1 M ± (0.15 % R + 10 m) ± (0.
PAGE 11
MMU 0102, MMA 0204, MMB 0207 - Professional www.vishay.com Vishay Beyschlag TEST PROCEDURES AND REQUIREMENTS IEC EN 60 068-2 (1) 60 115-1 TEST CLAUSE METHOD TEST REQUIREMENTS PERMISSIBLE CHANGE (R) PROCEDURE Stability for product types: 4.39 - Periodic electric overload: Standard operation mode Periodic electric overload: Power operation mode 4.22 6 (Fc) Vibration 4.40 - Electrostatic discharge (Human Body Model) 4.17 58 (Td) 4.18 58 (Td) 4.29 45 (XA) 4.30 45 (XA) 4.
PAGE 12
MMU 0102, MMA 0204, MMB 0207 - Professional www.vishay.com Vishay Beyschlag DIMENSIONS L K L1 D D1 DIMENSIONS AND MASS TYPE/SIZE L (mm) D (mm) L1 min. (mm) MMU 0102 2.2 + 0/- 0.1 1.1 + 0/- 0.1 MMA 0204 3.6 + 0/- 0.2 1.4 + 0/- 0.1 MMB 0207 5.8 + 0/- 0.15 2.2 + 0/- 0.2 D1 (mm) K (mm) MASS (mg) 1.2 D + 0/- 0.1 0.4 ± 0.05 8 1.8 D + 0/- 0.15 0.75 ± 0.1 22 3.2 D + 0/- 0.2 1.1 ± 0.
PAGE 13
MMU 0102, MMA 0204, MMB 0207 - Professional www.vishay.com Vishay Beyschlag HISTORICAL 12NC INFORMATION Last Digit of 12NC Indicating Resistance Decade • The resistors had a 12-digit numeric code starting with 2312. RESISTANCE DECADE LAST DIGIT 0.1  to 0.999  7 • The subsequent 4 digits indicated the resistor type, specification and packaging; see the 12NC table. 1  to 9.99  8 • The remaining 4 digits indicated the resistance value: 10  to 99.9  9 100  to 999.
PAGE 14
Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product.