Assembly Guide X6000DA & X6200HRT/DA DUAL-ACTION ELLIPTICAL TRAINERS
X6000DA X6200HRT/DA dual-action elliptical trainers To avoid possible damage to this Elliptical Trainer, please follow these assembly steps in the correct order. Before proceeding though, find your new Elliptical Trainer’s serial number, located on the front foot axle tube, and enter here: Refer to this number when calling for service, and also enter this serial number on your Warranty Card and in your own records. Be sure to read your Owner’s Guide before using your new Elliptical Trainer.
TOOLS, HARDWARE, & PARTS INCLUDED 5 MM Allen Wrench 13 MM Wrench PINK BAG Screwdriver M8 x 45 Bolt Quantity: 2 (X6000DA only) MM M8 x 80 Bolt Quantity: 4 MM 5 MM L-Shaped Wrench PARTS BOX Rear Folding Axle, Qty: 1 • Stabilizer w/ Rubber Cover, Qty: 2 Toe Pieces, Qty: 2 • Rear Wheels, Qty: 2 Tension Control Knob, Qty: 1 (Model X6000DA only) Console, Qty: 1 • Power Supply, Qty: 1 (X6200HRT/DA only) • 13 Nut Cap, Qty: 2 • Water Bottle & Bracket, Qty: 1 • Heart Rate Chest Strap, Qty: 1 (Model X6200H
GREEN BAG BLUE BAG M8 Lock Washer Quantity: 2 M8 x 16 Bolt Quantity: 2 M16 Wavy Washer Quantity: 2 MM M8 Washer Quantity: 2 M5 x 25 Bolt Quantity: 1 (X6000DA only) M16 Washer Quantity: 2 MM M8 x 60 Bolt Quantity: 2 MM M8 Washer Quantity: 2 BLACK BAG M8 x 25 Washer Quantity: 2 M16 Wavy Washer Quantity: 2 M8 x 36 Bolt Quantity: 2 MM M6 x 12 Bolt Quantity: 2 MM M8 x 13 Nylock Nut Quantity: 2 MM M8 x 35 Washer Quantity: 2 M26 Wavy Washer Quantity: 2 M8 x 12 Bolt Quantity: 4 MM
STEP 1 ORANGE BAG • Install the left and right stabilizers with the four bolts (M8 x 16 ), using the Blue 5 Allen wrench. MM MM • Cover both stabilizers with the included rubber covers. • Insert the rear folding axle shaft into the rear tube.
STEP PINK BAG 3 • Mount the rear pedal arms to the front pedal arms using four bolts (M8 x 80 ) and four M8 NyLock nuts. Tighten with the 13 wrench. MM MM • X6000DA only: Install the foot toe pieces to the front pedal arms with two bolts (M8 x 45 ) using the Blue 5 Allen wrench.
STEP 4 STEP GREEN BAG • X6000DA only: Unfold the RPM sensor wire, located in the frame console mast bracket. Remove any kinks. • All models: Slide the rubber console mast cover onto the bottom of console mast, and slide it up as far as it will go. X6000DA • All models: Unfold the console cable and attach it to the string located at the bottom of the console mast. Guide the wire up through the mast while simultaneously sliding the console mast onto the frame bracket.
STEP BLACK BAG 5 • Slide a large wavy washer (M26) onto the console mast axle. Locate and slide the right upper handlebar bracket onto the console mast axle and attach with a washer (M8 x 35) and M8 NyLock nut, using the 13 wrench. Snap the plastic 13 nut caps over the nuts. MM MM STEP 5 • Slide a small wavy washer (M16) onto the lower pedal arm support, followed by the right lower arm. Attach with a washer (M8 x 25) and bolt (M8 x 12 ), using the Blue 5 Allen wrench.