Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. © Copyright 2012 Disclaimer The information in this document is subject to change without notice.
DLP Projector—User’s Manual Important Safety Information Important: It is strongly recommended that you read this section carefully before using the projector. These safety and usage instructions will ensure that you enjoy many years of safe use of the projector. Keep this manual for future reference. Symbols Used Warning symbols are used on the unit and in this manual to alert you of hazardous situations. The following styles are used in this manual to alert you to important information.
Preface Projector Installation Notice ¾ Place the projector in a horizontal position The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically, and may lead to other unpredictable damages. ¾ Allow at least 50 cm clearance around the exhaust vent. ¾ Ensure that the intake vents do not recycle hot air from the exhaust vent.
DLP Projector—User’s Manual Verify Installation Location ¾ To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper grounding and equalized ground potential for all of the equipment in the Projector System. ¾ The power code provided with the Projector should be used. In case of any missing item, other qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use 2-blade power cord.
Preface Choosing a Projector Edge blending application ¾ Not only brightness, bright balances, lens but stability is important too when choosing a projector. ¾ A projector need 30 to 60 minutes warm up to adjust properly. ¾ After lens shift, there should not be any optical distortion such as trapezoidal and barrel shape distortions. ¾ Quick dis-assemble lens need to be firmly secured, the electric motor cannot be mistakenly shift.
DLP Projector—User’s Manual Power Safety ¾ Only use the supplied power cord. ¾ Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. ¾ Remove the batteries from the remote control when storing or not in use for a prolonged period. Replacing the Lamp Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 41 for clear and safe instructions for this procedure.
Preface Main Features • Lightweight unit, easy to pack away and transport. • Compatible with all major video standards including NTSC, PAL, and SECAM. • A high brightness rating allows for presentations in daylight or in lit rooms. • Supports resolutions up to UXGA at 16.7 million colors to deliver crisp, clear images. • Flexible setup allows for front, rear projections. • Line-of-vision projections remain square, with advanced keystone correction for angled projections.
DLP Projector—User’s Manual Table of Contents GETTING STARTED .......................................................................................................................................................... 1 PACKING CHECKLIST ........................................................................................................................................................... 1 VIEWS OF PROJECTOR PARTS ............................................................................................
Preface LED ERROR MESSAGES ..................................................................................................................................................... 48 IMAGE PROBLEMS .............................................................................................................................................................. 48 LAMP PROBLEMS .............................................................................................................................................
GETTING STARTED Packing Checklist Carefully unpack the projector and check that the following items are included: DLP PROJECTOR WITH LENS CAP REMOTE CONTROL (WITH TWO AAA BATTERIES) (WITH TWO CHANGEABLE TIPS) RGB CABLE POWER CORD USB CABLE CD-ROM (THIS USER’S MANUAL) QUICK START GUIDE WARRANTY CARD POINTRACER CARRYING CASE Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work.
DLP Projector—User’s Manual Views of Projector Parts Front-right View 1 ITEM 23 4 5 LABEL 6 DESCRIPTION SEE PAGE: 1. IR receiver Receive IR signal from remote control 2. Height-adjuster button Push to release height adjuster 3. Height adjuster Adjusts level of projector 4. Lens Projection Lens 5. Focus ring Focuses the projected image 15 6. Function keys See Top view—On-screen Display (OSD) buttons and LEDs.
Preface Top view—On-screen Display (OSD) buttons and LEDs 10 5 MENU AUTO 2 SOURCE 4 3 12 9 1 11 6 ITEM 1. 8 7 LABEL (POWER) DESCRIPTION Turns the projector On or Off 2. SOURCE Detects the input device 3. AUTO Optimizes image size, position, and resolution 4. ▲ (Up cursor) / KEYSTONE Navigates and changes settings in the OSD Quick Menu – For Keystone 5. ► (Right cursor) Navigates and changes settings in the OSD 6. TEMP LED 7. LAMP LED 8.
DLP Projector—User’s Manual Rear view ITEM 1. LABEL AC IN DESCRIPTION Connect the POWER cable 2. (USB) 3. 12V TRIGGER Connect the DC 12V OUT 4. LAN Connect a LAN cable from Ethernet 5. VIDEO IN Connect the composite cable from a video device 6. AUDIO IN (L and R) Connect the audio cable from audio device 7. AUDIO IN – 1 Connect an AUDIO cable from audio device 8. VGA OUT Connect the RGB cable to a display 9. VGA IN Connect the RGB cable from a computer or components 10.
Preface Bottom view 1 2 1 ITEM LABEL 4 3 DESCRIPTION SEE PAGE: 1. Ceiling support holes Contact your dealer for information on mounting the projector on a ceiling 2. Tilt adjustor Rotate adjuster lever to adjust angle position. 3. Height adjustor Adjuster drops down when adjuster button is pushed. 4. Height adjustor button Push to release adjustor. 14 14 Note: When installing, ensure that you use only UL Listed ceiling mounts.
DLP Projector—User’s Manual Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation. 2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain reflective surfaces such as projector screens. 3.
Preface ITEM LABEL DESCRIPTION 1. IR transmitter Transmits signals to projector 2. Status LED Lights when the remote control is used 3. Laser Press to operate the on-screen pointer 4. Up Up arrow when connected through USB to a PC 5. Right Right arrow when connected through USB to a PC 6. Down Down arrow when connected through USB to a PC 7. Page Down Page down when connected through USB to a PC 8. Up cursor 9. Right cursor 10. Down cursor 11.
DLP Projector—User’s Manual Remote Control Operating Range The remote control uses infrared transmission to control the projector. It is not necessary to point the remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15 degrees above or below the projector level. If the projector does not respond to the remote control, move a little closer.
Preface SETUP AND OPERATION Inserting the Remote Control Batteries 1. 2. 3. Remove the battery compartment cover by sliding the cover in the direction of the arrow. Insert the battery with the positive side facing up. Replace the cover. Caution: 1. Only use AAA batteries (Alkaline batteries are recommended). 2. Dispose of used batteries according to local ordinance regulations. 3. Remove the batteries when not using the projector for prolonged periods.
DLP Projector—User’s Manual Starting and Shutting down the Projector 1. 2. 3. Connect the power cord to the projector. Connect the other end to a wall outlet. The POWER LED on the projector light. Turn on the connected devices. Ensure the LAMP LED not a flashing POWER orange. Then press the button to turn on the projector. The projector splash screen displays and connected devices are detected. See Setting an Access Password (Security Lock) on page 12 if security lock is enabled. 4.
Preface 5. When the “Power Off? /Press Power again” message appears, press the POWER button. The projector turns off. Caution: 1. Be sure to remove the lens cap before starting projector. 2. Do not unplug the power cord until the POWER LED stops flashing–indicating the projector has cooled down.
DLP Projector—User’s Manual Setting an Access Password (Security Lock) You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector. When enabled, the password must be entered after you power on the projector. (See Navigating the OSD on page 17 and Setting the OSD Language on page 18 for help on using OSD menus.) Important: Keep the password in a safe place. Without the password, you will not be able to use the projector.
Preface 5. You can use the cursor buttons ▲▼◄► either on keypad or IR remote control for password entry. You can use any combination including the same arrow five times, but not less than five. Press the cursor buttons in any order to set the password. Push the MENU button to exit the dialog box. 6. The password confirm menu appears when user presses the power-on key in case the Security Lock is enabled. Enter the password in the order you set it at step 5.
DLP Projector—User’s Manual Adjusting the Projector Level Take note of the following when setting up the projector: • The projector table or stand should be level and sturdy. • Position the projector so that it is perpendicular to the screen. • Ensure the cables are in a safe location. You could trip over them. D A C 1. To raise the level of the projector, lift the projector [A] and press the height-adjuster button [B]. The height adjuster drops down [C]. 2. 3.
Preface Adjusting Focus and Keystone 1. 2. Use the Image-focus control (on the projector only) to adjust the projected image. Use the KEYSTONE buttons (on the projector or the remote control) to correct image-trapezoid (wider top or bottom) effect. Remote control and OSD panel 3. The keystone control appears on the display.
DLP Projector—User’s Manual Adjusting the Volume 1. Press the Volume +/buttons on the remote control. The volume control appears on the display. 2. Press the MUTE button to turn off the volume (This feature is available only on the remote). — 16 — AUTO 3. Press the Left or Right Cursor buttons on the keypad to adjust Volume +/-.
Preface ON-SCREEN DISPLAY (OSD) MENU SETTINGS OSD Menu Controls The projector has an OSD that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control cursor buttons or the buttons on the top of the projector to navigate and make changes to the OSD. The following illustration shows the corresponding buttons on the projector. 5 4 M ENU AUTO SOURCE 1 2 3 1. To enter the OSD, press the MENU button. 2. There are five menus.
DLP Projector—User’s Manual Setting the OSD Language Set the OSD language to your preference before continuing. 1. Press the MENU button. Press the cursor ◄► button to navigate to Installation I. 2. Press the cursor ▲▼ button until Language is highlighted. 3. Press the cursor ◄► button until the language you want is highlighted. 4. Press the MENU button twice to close the OSD.
Preface OSD Menu Overview Use the following illustration to quickly find a setting or determine the range for a setting.
DLP Projector—User’s Manual OSD Sub-Menu Overview — 20 —
Preface Image Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Image Menu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to change values for settings. ITEM DESCRIPTION Display Mode Press the cursor ◄► button to set the Display Mode. Brilliant Color Press the cursor ◄► button to adjust the Brilliant Color value. Brightness Press the cursor ◄► button to adjust the display brightness.
DLP Projector—User’s Manual Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲ to move to the Advanced menu and then press Enter or ►. Press ▼▲ to move up and down in the Advanced menu. ITEM DESCRIPTION Color Space Press the cursor ◄► button to adjust the color space. (Range: Auto – RGB – YPbPr – YCbCr) Color Temperature Press the cursor ◄► button to adjust the color temperature.
Preface Color Manager Press (Enter) / ► to enter the Color Manager sub menu. ITEM DESCRIPTION Red Select to enter the Red Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. Green Select to enter the Green Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. Blue Select to enter the Blue Color Manager. Press the ◄► buttons to adjust the Hue, Saturation, and Gain. Cyan Select to enter the Cyan Color Manager.
DLP Projector—User’s Manual Computer Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Computer menu. Press the cursor ▲▼ button to move up and down in the computer menu. Press ◄► to change values for settings. ITEM DESCRIPTION Horizontal Position Press the cursor ◄► button to adjust the display position to left or right. Vertical Position Press the cursor ◄► button to adjust the display position to up or down.
Preface Video/Audio Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Video/Audio menu. Press the cursor ▲▼ button to move up and down in the Video/Audio menu. Press ◄► to change values for settings. ITEM DESCRIPTION Video AGC Press the ◄► buttons to enable or disable the Automatic Gain Control for video source. Video Saturation Press the ◄► buttons to adjust the video saturation. Video Tint Press the ◄► buttons to adjust the video tint/hue.
DLP Projector—User’s Manual Audio Press ITEM (Enter) / ► to enter the Audio sub menu. DESCRIPTION Volume Press the ◄► buttons to adjust the audio volume. (Range: 0~8) Mute Press the ◄► buttons to turn on or off the speaker. Audio Input Press the cursor ◄► button to select audio input. (Range: Mini, Mini2, RCA, HDMI (It is only displayed while HDMI is active.
Preface Installation I Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installation I menu. Press the cursor ▲▼ button to move up and down in the Installation I menu. Press ◄► to change values for settings. ITEM DESCRIPTION Language Press the cursor ◄► button to select a different localization Menu. Blank Screen Press the cursor ◄► button to select different color to blank the screen.
DLP Projector—User’s Manual Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Installation I menu. Press ▲▼ to move to the Advanced menu and then press Enter or ►. Press ▲▼ to move up and down in the Advanced menu. Press ◄► to change values for setting. ITEM DESCRIPTION Security Lock Press the cursor ◄► button to enable or disable security lock function. Keypad Lock Press the cursor ◄► button to enable or disable keypad lock function.
Preface Presentation Timer The Presentation Timer function can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Press (Enter) / ► to enter the Presentation Timer sub menu. ITEM DESCRIPTION Timer Press the cursor ◄► button to enable or disable presentation timer function. Timer Period Press the cursor ◄► button to adjust the display timer period. Timer Reset Press (Enter) / ► to reset presentation timer counter.
DLP Projector—User’s Manual Installation II Menu Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installation II menu. Press the cursor ▲▼ button to move up and down in the Installation II menu. ITEM DESCRIPTION Auto Source Press the cursor ◄► button to enable or disable automatic source detection. (Range: On ~ Off) Auto Power Off (min.) Press the cursor ◄► button to enable or disable automatic shutdown of lamp when no signal.
Preface Advanced Feature Press the Menu button to open the OSD menu. Press ◄► to move to the Installation II menu. Press ▲▼ to move to the Advanced menu and then press Enter or ►. Press ▲▼ to move up and down in the Advanced menu. Press ◄► to change values for setting. ITEM DESCRIPTION OSD Menu Setting Press Enter / ► to enter the OSD setting menu. See page 32 for more information on OSD Menu Setting. Peripheral Test Press Enter/ ► to enter the Peripheral Test menu.
DLP Projector—User’s Manual OSD Menu Setting ITEM DESCRIPTION Menu Position Press ◄► button to select different OSD location. Translucent Menu Press ◄► button to select OSD background translucent level. Menu Display Press ◄► button to select OSD timeout delay. Peripheral Test ITEM DESCRIPTION Remote Control Test Press (Enter) / ► to test the IR remote controller for diagnostic. Color Test Press (Enter) / ► to select different colors on screen.
Preface Lamp Hour Reset Please refer to Resetting the Lamp on page 44 to reset the lamp hour counter.
DLP Projector—User’s Manual 3D ITEM DESCRIPTION 3D Press ◄► to select Off, DLP-Link or IR. 3D Sync Invert Press ◄► to turn 3D Sync Invert On or Off. Note: 1. The 3D OSD menu item is gray if there is no appropriate 3D source. This is the default setting. 2. When the projector is connected to an appropriate 3D source, the 3D OSD menu item is enabled for selection. 3. Use 3D glasses to view a 3D image. 4. You need 3D content from a 3D DVD or 3D media file. 5.
Preface Network ITEM DESCRIPTION Network State Displays the network connection status. DHCP Press ◄► to turn DHCP On or Off. Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and DNS fields. IP Address Enter a valid IP address if DHCP is turned off. Subnet Mask Enter a valid Subnet Mask if DHCP is turned off. Gateway Enter a valid Gateway address if DHCP is turned off. DNS Enter a valid DNS name if DHCP is turned off. Apply Press (Enter) / ► to confirm settings.
DLP Projector—User’s Manual For simplicity and ease of operation, the projector provides diverse networking and remote management features. The LAN/RJ45 function of the projector through a network, such as remotely manage: Power On/Off, Brightness and Contrast settings. Also, projector status information, such as: Video-Source, Sound-Mute, etc. LAN_RJ45 1. Connect an RJ45 cable to RJ45 ports on the projector and the PC (Laptop). 2. On the PC (Laptop), select Start → Control Panel → Network Connections.
Preface 3. Right-click on Local Area Connection, and select Properties. 4. In the Properties window, select the General tab, and select Internet Protocol (TCP/IP). 5. Click Properties. 6. Click Use the following IP address and fill in the IP address and Subnet mask, then click OK.
DLP Projector—User’s Manual 7. Press the Menu button on the projector. 8. Select Installation II → Advanced → Network. 9. After getting into Network, input the following: ` DHCP: Off ` IP Address: 10.10.10.10 ` Subnet Mask: 255.255.255.0 ` Gateway: 0.0.0.0 ` DNS Server: 0.0.0.0 10. Press (Enter) / ► to confirm settings. Open a web browser (for example, Microsoft Internet Explorer with Adobe Flash Player 9.0 or higher). 11. In the Address bar, input the IP address: 10.10.10.10. 12. Press (Enter) / ►.
Preface CATEGORY Crestron Control Projector Network Configuration User Password Admin Password ITEM INPUT-LENGTH IP Address 14 IP ID 3 Port 5 Projector Name 10 Location 9 Assigned To 8 DHCP (Enabled) (N/A) IP Address 15 Subnet Mask 15 Default Gateway 15 DNS Server 15 Enabled (N/A) New Password 15 Confirm 15 Enabled (N/A) New Password 15 Confirm 15 For more information, please visit http://www.crestron.com.
DLP Projector—User’s Manual Factory Reset Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the Factory (Enter) / ► to reset all the menu items to the factory default values Reset sub menu and press (except Language and Security Lock). Status Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the (Enter) / ► to enter the Status sub menu. Installation II sub menu and press ITEM DESCRIPTION Active Source Display the activated source.
Preface MAINTENANCE AND SECURITY Replacing the Projection Lamp The projection lamp should be replaced when it burns out. It should only be replaced with a certified replacement part, which you can order from your local dealer. Important: a. The projection lamp used in this product contains a small amount of mercury. b. Do not dispose this product with general household waste. c. Disposal of this product must be carried out in accordance with the regulations of your local authority.
DLP Projector—User’s Manual 2. 3. Remove the lamp compartment cover. Remove the three screws from the lamp module. 4. Lift the module handle up. 5. Pull firmly on the module handle to remove the lamp module.
Preface 6. Reverse steps 1 to 5 to install the new lamp module. While installing, align the lamp module with the connector and ensure it is level to avoid damage. Note: The lamp module must sit securely in place and the lamp connector must be connected properly before tightening the screws.
DLP Projector—User’s Manual Resetting the Lamp After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following: 1. 2. 3. 4. Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the Installation II menu. Press the cursor button to move down to Advanced. Press the cursor ▼▲ button to move down to Lamp Hour Reset. Press the cursor ► or Enter button. A message screen appears. 5. 6. Press ▼▲◄► buttons to reset the lamp hour.
Preface Cleaning the Projector Cleaning the projector to remove dust and grime will help ensure trouble-free operation. Warning: 1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so could result in a severe burn. 2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings on the projector. 3.
DLP Projector—User’s Manual Using the Kensington® Lock & Using the Security Bar Using the Kensington® Lock If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable. Note: Contact your vendor for details on purchasing a suitable Kensington security cable. The security lock corresponds to Kensington’s MicroSaver Security System. If you have any comment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A.
Preface TROUBLESHOOTING Common problems and solutions These guidelines provide tips to deal with problems you may encounter while using the projector. If the problem remains unsolved, contact your dealer for assistance. Often after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Check the following before proceeding to the problem-specific solutions. • Use some other electrical device to confirm that the electrical outlet is working.
DLP Projector—User’s Manual LED Error Messages POWER LED BLINK OVER TEMP LED LAMP LED BLINK ON 0 0 Over temperature 0 ON 0 Thermal break status error 4 0 0 Lamp error 0 0 ON Fan1 error 6 0 1 Fan2 error 6 0 2 Fan3 error 6 0 3 Lamp door open 7 0 0 DMD error 8 0 0 Color wheel error 9 0 0 ERROR CODE MESSAGES Standby mode In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector.
Preface Lamp Problems Problem: There is no light from the projector 1. Check that the power cable is securely connected. 2. Ensure the power source is good by testing with another electrical device. 3. Restart the projector in the correct order and check that the Power LED is green. 4. If you have replaced the lamp recently, try resetting the lamp connections. 5. Replace the lamp module. 6. Put the old lamp back in the projector and have the projector serviced. Problem: The lamp goes off 1.
DLP Projector—User’s Manual HDMI Q & A Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI cable? Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or HighSpeed cables. ․Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or up to 2.25Gbps, which is the equivalent of a 720p/1080i signal. ․ High Speed (or “category 2”) HDMI cables have been tested to perform at speeds of 340Mhz or up to 10.
Preface SPECIFICATIONS Specifications Model D856STPB D858WTPB Display type TI DMD 0.55” TI DMD 0.65” XGA 1024x768 WXGA 1280x800 Resolution 0.66m ~ 1.69m Projection distance Projection screen size 49.9" ~ 127.9" Manual Focus/Fix Zoom Projection lens Fix Zoom ratio +/- 40 steps Vertical keystone correction Projection methods 58.4" ~ 149.
DLP Projector—User’s Manual Projection Distance vs. Projection Size Projection Distance and Size Table D856STPB IMAGE DIAGONAL (INCH) IMAGE WIDTH (INCH) IMAGE HIGHT (INCH) PROJECTION DISTANCE (MM) FROM OFFSET-A ( MM ) 49.9 39.92 29.94 659.1 108.4 60 48 36 792.5 130.3 80 64 48 1056.6 173.7 100 80 60 1320.8 217.2 120 96 72 1585.0 260.6 127.9 102.32 76.74 1689.3 277.
Preface Timing Mode Table SIGNAL RESOLUTION H-SYNC (KHZ) V-SYNC (HZ) COMPOSITE / S-VIDEO COMPONENT RGB DVI/ HDMI NTSC - 15.734 60.0 O - - - - 15.625 50.0 O - - - 720 x 400 37.9 85.0 - - O O 640 x 480 31.5 60.0 - - O O 640 x 480 37.9 72.0 - - O O 640 x 480 37.5 75.0 - - O O 640 x 480 43.3 85.0 - - O O 800 x 600 35.2 56.0 - - O O 800 x 600 37.9 60.0 - - O O 800 x 600 48.1 72.0 - - O O 800 x 600 46.9 75.
DLP Projector—User’s Manual SIGNAL RESOLUTION H-SYNC (KHZ) V-SYNC (HZ) COMPOSITE / S-VIDEO COMPONENT RGB DVI/ HDMI 1600 x 1200 75.0 60.0 - - O O 640 x 480 35.0 66.68 - - O O 832 x 624 49.725 74.55 - - O O 1024 x 768 60.24 75.0 - - O O 1152 x 870 68.68 75.06 - - O O 480i 15.734 60.0 - O - O 576i 15.625 50.0 - O - O 480p 31.469 60.0 - O - O 576p 31.25 50.0 - O - O 720p 37.5 50.0 - O - O 720p 45.0 60.0 - O - O 1080i 33.8 60.
Preface Projector Dimensions – 55 –
DLP Projector—User’s Manual REGULATORY COMPLIANCE FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Preface APPENDIX I RS-232C Protocol RS232 Setting Baud rate: Parity check: Data bit: Stop bit: 9600 None 8 1 Flow Control None Minimum delay for next command: 1ms Control Command Structure Header code HEX ASCII `V’ Command code Command Command Data code Data Data End code 0Dh CR Operation Command Note: XX=00-98, projector's ID, XX=99 is for all projectors Return Result P=Pass / F=Fail n: 0:Disable/1: Enable/Value(0~9999) ASCII VXXS0001 VXXS0002 VXXS0003 VXXG0004 VXXS0006 Command Group 00 Funct
DLP Projector—User’s Manual VXXS0105n Set Sharpness VXXG0106 Get Color Temperature VXXS0106n Set Color Temperature VXXG0107 VXXS0107n ASCII VXXS0201 VXXS0202 VXXS0203 VXXS0204 VXXS0205 VXXS0206 VXXS0207 VXXG0220 0~31 0:Cold 1:Normal 2:Warm 0:Cold 1:Normal 2:Warm P/F Pn/F P/F Get Gamma 0:PC 1:MAC 2:Video 3:Chart 4: B&W Pn/F Set Gamma 0:PC 1:MAC 2:Video 3:Chart 4: B&W P/F Command Group 02 Function Description Select RGB Select RGB2 Select DVI Select Video Select S-Video Select HDMI Select B
Preface VXXG0303 VXXS0303n VXXG0304 VXXS0304n VXXG0305 VXXS0305n Auto Keystone On Auto Keystone On Freeze On Freeze On Volume Volume VXXG0308 Projection Mode n=0~8 n=0~8 0:Front 1:Rear 2:Ceiling 3:Rear+Ceiling Pn/F P/F Pn/F P/F Pn/F P/F Pn/F VXXS0308n Projection Mode 0:Front 1:Rear 2:Ceiling 3:Rear+Ceiling VXXG0309 Get vertical keystone value n= -40~40 Pn/F VXXS0309n Set vertical keystone value n= -40~40 P/F VXXG0311 VXXS0311n Adjust the zoom Adjust the zoom n=-10~10 n=-10~10 Pn/F P/F A