VIVOTEK Fixed Dome & PTZ Series Wall-mount Bracket User’s Manual Using AM-214 wall-mount bracket and compatible accessories Rev. 1.
AM-214 Wall-mount Bracket I Compatible VIVOTEK Cameras Fixed Dome series FD8133, FD8134, FD8133V, FD8134V, FD8161, FD7132, FD7131, FD8162, FD8135H, FD8362E, FD8362, FD8372, FD8335H, FD8361, FD8361L, FD8131 PTZ series PZ7111, PZ7112, PZ7121, PZ7122, PZ7131, PZ7132, PZ7151, PZ7152, PZ81x1W, PZ81x1 You may also refer to VIVOTEK's website for the list of supported models. Support for other models can be available through time.
English II Accessories Adaptor ring for FD8162 III Installation Mounting Hole Definitions Above are the locations of different groups of mounting holes for matching different cameras: Hole Type A B C D E1 E2 E3 Applicable Cameras Screw No.
Refer to the table below for the description of the included screws: Screw Description Quantity M4X15 Phillips pan head 4 Applies to A holes M3X4 Phillips pan head (black) 2 D holes for PZ and PT series M4X8XD6 Phillips pan head 3 B holes M4X25XD9 Phillips pan head 4 Securing the bracket to wall M3x6 Phillips pan head 2 C holes Plastic anchors 4 Securing the bracket to wall NOTE: 1.
English Wall Mount Installation - FD8134V Below is a general, sample procedure using a wall mount bracket: 1. Locate the position where you want to install the wall mount bracket and camera. Drill holes on the wall for securing the bracket and for routing the cables. 2. Secure the bracket by hammering anchors into the wall and then fasten screws through the four mounting holes on the bracket. 3. Route power lines and other cables through the wall and the bracket. 4.
5. Proceed with initial setup such as enabling network access, focus tuning, or zooming. When done, secure the outer dome cover. NOTE: Use the correct type of screws when installing cameras to the mounting cap. Refer to page 3 for the screw type.
English Wall Mount Installation - FD8134 Below is a sample procedure using wall mount bracket and an FD8134: 1. Determine a hard surface wall location, and use the four mounting holes on the wall mount bracket to mark the positions where holes will be drilled to secure the bracket. M3X6 Screws 2. Drill holes on the wall for passing cables and for securing the wall mount bracket. 3. Secure the bracket by hammering anchors into the wall and then fasten screws. 4.
Wall Mount Installation - FD8162 Below is a sample procedure using wall mount bracket and an FD8162: 1. Determine a hard surface wall location, and use the four mounting holes on the bracket to mark the positions where holes will be drilled to secure the bracket. A* holes M4X15 Camera Lens Orientation 2. Drill holes on the wall for securing the bracket and for routing cables. 3. Route cables through the wall and bracket. 4.
English 6. Secure the camera to the adaptor ring using the included screws. 7. Connect power lines and cables to the camera. 8. Proceed with initial setup such as enabling network access, focus tuning, or zooming. When done, secure the outer dome cover. Wall Mount Installation - PZ7151 (and Applies to All PZ Series) Below is a general, sample procedure for installing a PZ pr PT series camera with the wall mount bracket: 1. Detach the mount panel by loosening 5 screws from the wall mount bracket.
2. Secure the camera from the inner side of the mount panel by driving M3 screws to the bottom of camera. 3. Locate the position where you want to install the wall mount bracket. Drill holes on the wall for securing the bracket and for routing cables. 4. Route power lines and other cables through the wall and the bracket. 5. Secure the wall mount bracket to the wall using the included fasteners and screws. 6.
English Wall Mount Installation - FD8161 Below is a general, sample procedure using a wall mount bracket with the FD8161 camera: 1. Locate the position where you want to install the wall mount bracket and camera. Drill holes on the wall for securing the bracket and for routing cables. 2. You can route cables through the hole in the center of the bracket and the space beneath the camera. 3. Secure the wall mount bracket to the wall using the included plastic anchors and screws.
6. Attach dome cover to the camera.
Below is a general, sample procedure using a wall mount bracket with the FD8362E, FD8335H, and FD8372 cameras: 1. Locate the position where you want to install the wall mount bracket and camera. Drill holes on the wall for securing the bracket and for routing cables. 2. You can route cables through the hole in the center of the bracket. 3. Secure the wall mount bracket to the wall using the included plastic anchors and screws. 4.
This page is intentionally left blank.
English This page is intentionally left blank.
