OWNER'S MANUAL
VÄLKOMMEN! We trust that you will enjoy many years of safe driving in your Volvo, an automobile designed with your safety and comfort in mind. To help get the most from your Volvo, we urge you to familiarize yourself with the instructions and maintenance information in this owner’s manual. The owner’s manual can also be found in a mobile app (Volvo manual) and on Volvo Car’s support site at support.volvocars.com.
CONTENTS INTRODUCTION 2 SAFETY INSTRUMENTS AND CONTROLS On-board owner's manual 10 Occupant safety 26 Instrument overview 60 Owner's information 12 Recall information 26 Information displays – introduction 63 Contacting Volvo 13 Reporting safety defects 27 Eco Guide* and Power Meter* 66 About this manual 13 Seat belts – general 28 Information displays – indicator symbols 67 Change of ownership 17 Seat belts – buckling/unbuckling 29 Information displays – warning symbols 69
CLIMATE Active Bending Lights (ABL)* 86 Power moonroof – operation 102 Climate – general information 120 Auxiliary lights* 87 HomeLink® Wireless Control System* – introduction 103 Climate – sensors 121 Air quality HomeLink® Wireless Control System* – programming 121 104 Interior Air Quality System (IAQS)* 122 Volvo Sensus 107 Climate – menu settings 123 Information display – menu controls 108 Air distribution – general 123 Information display – menu overview 108 Electronic climat
LOADING AND STORAGE 4 LOCKS AND ALARM Storage spaces 134 Remote key and key blade 144 Alarm indicator 162 Tunnel console 136 Remote key – loss 144 Alarm – arming/disarming 163 Tunnel console – 12-volt sockets 136 Key memory 145 Alarm signal 163 Glove compartment 137 Locking/unlocking confirmation 146 Alarm – turning off 164 Vanity mirror 137 Immobilizer (start inhibitor) 146 Alarm-related functions 164 12-volt socket in the trunk* 137 Remote key – functions 147 Loading –
DRIVER SUPPORT Active chassis* (Four C) 166 Radar sensor 185 Stability system – introduction 166 Adaptive Cruise Control – limitations 186 Stability system – operation 167 Adaptive Cruise Control – symbols and messages 188 190 Stability system – symbols and messages 169 Adjustable steering force* 171 Adaptive Cruise Control – troubleshooting Road Sign Information (RSI)* – introduction 171 Distance Alert – introduction 191 Distance Alert – operation 191 Distance Alert – limitations 192
STARTING AND DRIVING Park Assist Pilot (PAP)* – function 235 Starting the engine 252 Brake lights 272 Park Assist Pilot (PAP)* – operation 236 Switching off the engine 253 Emergency Brake Assistance (EBA) 272 Park Assist Pilot (PAP)* – limitations 238 254 Parking brake – general information 273 Park Assist Pilot (PAP)* – symbols and messages 239 Engine Remote Start (ERS)* – introduction Parking brake – applying 254 273 Parking brake – releasing 274 Park assist – troubleshooting 239
WHEELS AND TIRES MAINTENANCE AND SERVICING Tires – general information 292 Tires – storage and age 293 Tires – tread wear indicator 294 Tires – tire economy 294 Changing a wheel – direction of rotation 295 Changing a wheel – removing wheel 295 Tire Pressure Monitoring System (TPMS) – general information 312 Tire Pressure Monitoring System (TPMS) – changing wheels 313 Tire Pressure Monitoring System (TPMS) – recalibrating 314 Tire Pressure Monitoring System (TPMS) – activating/deactivatin
SPECIFICATIONS 8 INDEX Wiper blades – service position 344 Label information 368 Wiper blades – windshield 345 Dimensions 371 Engine compartment – washer fluid 346 Weights 373 Battery – symbols 346 Engine specifications 375 Battery – handling 347 Oil specifications 376 Battery – maintenance 348 Oil volume 377 Battery – changing 349 Coolant – specification and volume 378 Fuses – introduction 351 378 Fuses – engine compartment 352 Transmission oil – specification and volume
INTRODUCTION
INTRODUCTION On-board owner's manual • Favorites: Quick access to frequently read • Quick Guide: A selection of articles cover- To open the owner's manual, press the MY CAR button on the center console, press OK/MENU and select Owner's manual. Select the symbol in the lower right-hand corner for additional information about the on-board owner's manual. For basic information, see "Infotainment - operating the system." The following sections also provide more detailed information.
INTRODUCTION 3. To switch from letter entry mode to the entry mode for numbers or special characters, or to go view surf history, turn TUNE to one of the selections (see the explanation in the following table) in the list for switching character entry mode (2) and press OK/MENU. 123/A BC Toggle between letters and numbers by pressing OK/MENU. => This leads to surf history. Turn TUNE to select a web address and press OK/MENU to go to the website. Go Go to the website by pressing OK/ MENU.
INTRODUCTION || such texts in the article will be displayed here. Turn TUNE to navigate among the links or scroll in an article. When you have scrolled to the beginning/end of an article, you can return to the start page or a favorite by scrolling one additional step up/down. Press OK/MENU to activate a selection or highlighted link. Press EXIT to return to the previous view. Related information • 12 Information on the Internet (p.
INTRODUCTION Contacting Volvo About this manual The driver is always responsible for operating the vehicle in a safe manner and for complying with current statutes and regulations. In the USA: Volvo Cars of North America, LLC Reading your owner's manual is a good way to familiarize yourself with the features and systems in your vehicle.
INTRODUCTION || There are four ways of finding information articles in the on-board owner's manual: The owner's manual in mobile devices • Searching: search for an article. • Categories: All of the articles are sorted by category. Decals • Favorites: Quick access to frequently read There are various types of decals in the vehicle whose purpose is to provide important information in a clear and concise way. The importance of these decals is explained as follows, in descending order of importance.
INTRODUCTION Risk of damage to the vehicle Types of lists used in the owner's information Information Procedures Procedures (step-by-step instructions), or actions that must be carried out in a certain order, are arranged in numbered lists in this manual. White ISO symbols and white text/image on a black or blue warning background and space for a message. If the information on decals of this type is ignored, damage to the vehicle could result.
INTRODUCTION || Bullet lists Bullets are used to differentiate a number of components/functions/points of information that can be listed in random order. WARNING If your vehicle is involved in an accident, unseen damage may affect its drivability and safety. For example: • • Coolant Engine oil Continues on next page } }This symbol can be found at the lower right corner to indicate that the current topic continues on the following page.
INTRODUCTION operation in the U.S., Canada and other countries. • • • All information, illustrations and specifications contained in this manual are based on the latest product information available at the time of publication. Please note that some vehicles may be equipped differently, depending on special legal requirements. Optional equipment described in this manual may not be available in all markets.
INTRODUCTION || tinely acquired during a crash investigation. To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. Rockleigh, New Jersey 07647 Volvo Structural Parts Statement 1-800-458-1552 Volvo has always been and continues to be a leader in automotive safety. Furthermore, your vehicle is equipped with a number of computers whose task is to continuously control and monitor the vehicle’s operation.
INTRODUCTION quality of these used parts may also have been affected due to environmental exposure. Related information • • • Information on the Internet Additional information regarding your vehicle can be found at www.volvocars.com. Important warnings (p. 22) Support on the Internet Information on the Internet (p. 19) Go to support.volvocars.com or use the QR code below to visit the site, which is available in most markets. Contacting Volvo (p.
INTRODUCTION Volvo ID Open Source Software Notice This is your personal ID that can be used to access a number of services1 The systems in your Volvo contain certain free/ open source and other software.
INTRODUCTION Volvo and the environment Volvo is committed to the well being of its customers. As a natural part of this commitment, we care about the environment in which we all live. Concern for the environment means an everyday involvement in reducing our environmental impact. Volvo's environmental activities are based on a holistic view, which means we consider the overall environmental impact of a product throughout its complete life cycle.
INTRODUCTION Important warnings • Driver distraction A driver has a responsibility to do everything possible to ensure his or her own safety and the safety of passengers in the vehicle and others sharing the roadway. Avoiding distractions is part of that responsibility. Driver distraction results from driver activities that are not directly related to controlling the vehicle in the driving environment. Your new Volvo is, or can be, equipped with many feature-rich entertainment and communication systems.
INTRODUCTION Volvo On Call Roadside Assistance Technician certification Your new Volvo comes with a four year ON CALL roadside assistance. In addition to Volvo factory training, Volvo supports certification by the National Institute for Automotive Service Excellence (A.S.E.). Additional information, features, and benefits of this program are described in a separate information package in your glove compartment. If you require assistance, dial: In the U.S.
SAFETY
SAFETY • • Never drink and drive. Recall information Our concern for safety dates back to 1927 when the first Volvo rolled off the production line. Three-point seat belts (a Volvo invention), safety cages, and energy-absorbing impact zones were designed into Volvo vehicles long before it was fashionable or required by government regulation. If you are taking any medication, consult your physician about its potential effects on your driving abilities.
SAFETY Reporting safety defects The following information will help you report any perceived safety-related defects in your vehicle. Reporting safety defects in the U.S. If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Volvo Cars of North America, LLC.
SAFETY Seat belts – general Seat belts should always be worn by all occupants of your vehicle. Children should be properly restrained, using an infant, car, or booster seat determined by age, weight and height. Volvo also believes no child should sit in the front seat of a vehicle. collision, limits the peak forces exerted by the seat belt on the occupant. WARNING • Seat belt maintenance Check periodically that the seat belts are in good condition. Use water and a mild detergent for cleaning.
SAFETY • • • Seat belts – buckling/unbuckling Seat belts should be used by all occupants in the vehicle when it is in motion. Buckling a seat belt Pull the belt out far enough to insert the latch plate into the receptacle until a distinct click is heard. The seat belt retractor is normally "unlocked" and you can move freely, provided that the shoulder belt is not pulled out too far.
SAFETY || Unbuckling the seat belt Seat belt reminder Rear seats To remove the seat belt, press the red section on the seat belt receptacle. Before exiting the vehicle, check that the seat belt retracts fully after being unbuckled. If necessary, guide the belt back into the retractor slot. The seat belt reminder is intended to alert all occupants of the vehicle that their seat belts should be fastened before the vehicle begins to move.
SAFETY Seat belts – pregnancy Related information • • • Seat belts – buckling/unbuckling (p. 29) Seat belt reminder (p. 30) Child restraints (p. 47) Supplemental Restraint System (SRS) As an enhancement to the three-point seat belts (p. 28), your Volvo is equipped with a Supplemental Restraint System (SRS). G020998 The seat belt should always be worn during pregnancy. However, it is crucial that it be worn correctly.
SAFETY || Volvo's SRS consists of seat belt pretensioners, front airbags (p. 33), side impact airbags (p. 39), a front passenger occupant weight sensor (p. 36), and inflatable curtains (p. 40). All of these systems are monitored by the SRS control module. An SRS warning light in the instrument panel (see the illustration) illuminates when the ignition is in modes I or II, and will normally go out after approximately 6 seconds if no faults are detected in the system.
SAFETY Front airbags WARNING The front airbags supplement the three-point seat belts (p. 28). For these airbags to provide the protection intended, seat belts must be worn at all times. • • • G018665 Location of the passenger's side front airbag The front airbag system The front airbag system includes gas generators surrounded by the airbags, and deceleration sensors that activate the gas generators, causing the airbags to be inflated with nitrogen gas.
SAFETY || certain non-frontal collisions where rapid deceleration occurs. • The SRS (p. 31) sensors, which trigger the front airbags, are designed to react to both the impact of the collision and the inertial forces generated by it, and to determine if the intensity of the collision is sufficient for the seat belt pretensioners and/or airbags to be deployed. • • However, not all frontal collisions activate the front airbags. • If the collision involves a nonrigid object (e.g.
SAFETY NOTE • • • Airbag decals Volvo's front airbags use special sensors that are integrated with the front seat buckles. The point at which the airbag deploys is determined by whether or not the seat belt is being used, as well as the severity of the collision. WARNING • Deployment of front airbags occurs only one time during an accident. In a collision where deployment occurs, the airbags and seat belt pretensioners activate. Some noise occurs and a small amount of powder is released.
SAFETY || Related information • • • • Occupant Weight Sensor (p. 36) Side impact protection (SIPS) airbags (p. 39) Inflatable Curtain (IC) (p. 40) Supplemental Restraint System (SRS) (p. 31) Occupant Weight Sensor The Occupant Weight Sensor (OWS) is designed to meet the regulatory requirements of Federal Motor Vehicle Safety Standard (FMVSS) 208 and is designed to disable (will not inflate) the passenger's side front airbag under certain conditions.
SAFETY NOTE • When the ignition is switched on, the OWS indicator light will illuminate for several seconds while the system performs a self-diagnostic test. • However, if a fault is detected in the system: • • The OWS indicator light will stay on • The message Pass. Airbag OFF Service urgent will be displayed in the information display. PASSENGER AIRBAG OFF indicator lamp is lit. Make sure the child restraint is properly installed.
SAFETY || Modifications If you are considering modifying your vehicle in any way to accommodate a disability, for example by altering or adapting the driver's or front passenger's seat(s) and/or airbag systems, please contact Volvo at: WARNING • In the USA Volvo Cars of North America, LLC Customer Care Center 1 Volvo Drive • P.O. Box 914 Rockleigh, New Jersey 07647 1-800-458-1552 In Canada Volvo Cars of Canada Corp.
SAFETY • Supplemental Restraint System (SRS) (p. 31) Side impact protection (SIPS) airbags As an enhancement to the structural side impact protection built into your vehicle, it is also equipped with Side Impact Protection System (SIPS) airbags. Driver's side SIPS airbag G032949 Related information Location of the side impact (SIPS) airbags (front seats only) The SIPS airbag system is designed to help increase occupant protection in the event of certain side impact collisions.
SAFETY || NOTE WARNING SIPS airbag deployment (one airbag) occurs only on the side of the vehicle affected by the impact. The airbags are not designed to deploy in all side impact situations. • Components in the SIPS airbag system • This SIPS airbag system consists of a gas generator, the side airbag modules built into the outboard sides of both front seat backrests, and electronic sensors/wiring.
SAFETY WARNING • • • • The IC system is a supplement to the Side Impact Protection System. It is not designed to deploy during collisions from the rear of the vehicle. Never try to open or repair any components of the IC system. This should be done only by a trained and qualified Volvo service technician. Never hang heavy items from the ceiling handles. This could impede deployment of the Inflatable Curtain. The rear seat should not be loaded to a level higher than 2 in.
SAFETY || backrest/head restraint to help support the occupant's head before moving slightly rearward. This movement helps absorb some of the forces that could result in whiplash. WARNING • WARNING • • In the event of a rear-end collision, the hinges and brackets of the front seat backrests are designed to change position slightly to allow the 42 The WHIPS system is designed to supplement the other safety systems in your vehicle.
SAFETY WARNING • • Boxes, suitcases, etc. wedged behind the front seats could impede the function of the Whiplash Protection System. If the rear seat backrests are folded down, cargo must be secured to prevent it from sliding forward against the front seat backrests in the event of a collision from the rear. This could interfere with the action of the Whiplash Protection System.
SAFETY || If the vehicle has been involved in a collision, the text Safety mode See manual may appear in the information display. NOTE This text can only be shown if the display is undamaged and the vehicle's electrical system is intact. Crash mode is a feature that is triggered if one or more of the safety systems (e.g. front (p. 33) or side airbags (p. 39), an inflatable curtain (p. 40), or one or more of the seat belt pretensioners) has deployed.
SAFETY Crash mode – moving the vehicle Child safety If the message Normal mode appears after an attempt has been made to start the engine, Starting the vehicle after a crash (p. 44), the vehicle may be moved carefully from its present position, if for example, it is blocking traffic. It should, however, not be moved farther than is absolutely necessary. Children should always be seated safely when traveling in the vehicle.
SAFETY || When a child has outgrown the child safety seat, you should use the rear seat with the standard seat belt fastened. The best way to help protect the child here is to place the child on a cushion so that the seat belt is properly located on the hips (see Booster cushions (p. 53) for illustration). Legislation in your state or province may mandate the use of a child seat or cushion in combination with the seat belt, depending on the child's age and/or size. Please check local regulations.
SAFETY Child restraints Suitable child restraints should always be used when children travel in the vehicle. G022840 Convertible seat Infant seat There are three main types of child restraint systems: infant seats (p. 48), convertible seats (p. 51), and booster cushions (p. 53). They are classified according to the child's age and size.
SAFETY WARNING • • When not in use, keep the child restraint system secured or remove it from the passenger compartment to help prevent it from injuring passengers in the event of a sudden stop or collision. A small child's head represents a considerable part of its total weight and its neck is still very weak. Volvo recommends that children up to age 4 travel, properly restrained, facing rearward.
SAFETY Attach the seat belt to the infant seat according to the manufacturer's instructions. WARNING A child seat should never be used in the front passenger seat of any vehicle with a front passenger airbag – not even if the "Passenger airbag off" symbol near the rear-view mirror is illuminated (on vehicles equipped with Occupant Weight Sensor). If the severity of an accident were to cause the airbag to inflate, this could lead to serious injury or death to a child seated in this position.
SAFETY || NOTE WARNING It should not be possible to move the child restraint (child seat) more than 1 in. (2.5 cm) in any direction along the seat belt path. The locking retractor will automatically release when the seat belt is unbuckled and allowed to retract fully. G022846 5. Press the infant seat firmly in place, let the seat belt retract and pull it taut. A sound from the seat belt retractor's automatic locking function will be audible at this time and is normal.
SAFETY Convertible seats WARNING Suitable child restraints should always be used when children (depending on their age/size) are seated in the vehicle. • G022847 Securing a convertible seat with a seat belt • • Route the seat belt through the convertible seat G018630 WARNING Do not place the convertible seat in the front passenger's seat Always use a convertible seat that is suitable for the child's age and size. See the convertible seat manufacturer's recommendations. 1. 2.
SAFETY || 3. Pull the shoulder section of the seat belt out as far as possible to activate the belt's automatic locking function. NOTE WARNING It should not be possible to move the child restraint (child seat) more than 1 in. (2.5 cm) in any direction along the seat belt path. The locking retractor will automatically release when the seat belt is unbuckled and allowed to retract fully. 5. Press the convertible seat firmly in place, let the seat belt retract and pull it taut.
SAFETY Related information Child safety (p. 45) Booster cushions 3. Child restraints (p. 47) Booster cushions should be properly positioned in the vehicle. Infant seats (p. 48) Securing a booster cushion Fasten the seat belt by inserting the latch plate into the buckle (lock) until a distinct click is audible. ISOFIX/LATCH lower anchors (p. 54) G022852 Top tether anchors (p. 55) G022851 • • • • • Position the child correctly on the booster cushion Positioning the seat belt 4.
SAFETY || Related information • • • • • • Child safety (p. 45) Child restraints (p. 47) Infant seats (p. 48) Convertible seats (p. 51) ISOFIX/LATCH lower anchors (p. 54) ISOFIX/LATCH lower anchors 2. Lower anchors for ISOFIX/LATCH-equipped child seats are located in the rear, outboard seats, hidden below the backrest cushions. Kneel on the child restraint to press down the seat cushion and locate the anchors by feel. 3.
SAFETY Related information • • • Child safety (p. 45) Infant seats (p. 48) Convertible seats (p. 51) Top tether anchors Your Volvo is equipped with child restraint top tether anchorages in the rear seat. They are located on the rear parcel shelf. G018631 Child restraint anchorages Fasten the attachment correctly to the ISOFIX/LATCH lower anchors WARNING • • Be sure to fasten the attachment correctly to the anchor (see the illustration).
SAFETY || Securing a child seat WARNING 1. Place the child restraint on the rear seat. • 2. Fold up the plastic cover over the anchorage to be used. • 3. Route the top tether strap under the head restraint and attach it to the anchor. 4. Fold down the outboard head restraints or lower the center head restraint for easier access to the ISOFIX/LATCH anchor. 5. Attach lower tether straps to the lower ISOFIX/LATCH anchors.
SAFETY Related information • Detachable key blade – general information (p. 149) • Locking/unlocking – from inside (p.
INSTRUMENTS AND CONTROLS
INSTRUMENTS AND CONTROLS Instrument overview This overview shows the location of the instrument panel and center console displays, and controls/buttons/switches.
INSTRUMENTS AND CONTROLS }} 61
INSTRUMENTS AND CONTROLS || 62 Function See Function See Function See Controls for menus and messages, turn signals, high/low beams, trip computer (p. 71), (p. 90), (p. 83), (p. 110) In-door control panels (power windows, mirrors, central locking button) (p. 96), (p. 97), (p. 158) Power seat* adjustment controls (p. 76) Paddles for manually shifting gears* (p. 258) Hazard warning flashers (p. 89) (p. 83), (p. 282), (p. 160) Cruise control (p. 173) Horn, airbag (p. 82), (p.
INSTRUMENTS AND CONTROLS Information displays – introduction Gauges and indicators: analog instrument panel The displays show information on some of the vehicle's functions, such as cruise control, the trip computer and messages. The information is shown with text and symbols. Information displays: digital instrument panel* More detailed information can be found in the descriptions of the functions that use the information displays.
INSTRUMENTS AND CONTROLS || Gauges and indicators: digital instrument panel* Refueling – fuel requirements (p. 279) for additional information. Different themes (display alternatives) can be selected for the digital instrument panel: Coolant temperature gauge • • • Tachometer (engine speed in thousands of revolutions per minute (rpm)) Elegance Eco Performance To change themes, press the OK button on the left steering wheel lever and use the thumb wheel to scroll to Themes.
INSTRUMENTS AND CONTROLS Related information Power Meter (see Eco Guide* and Power Meter* (p. 66)). • • Gear indicator: Shows the currently selected gear • Indicator and warning symbols Instrument overview (p. 60) Information displays – indicator symbols (p. 67) Information displays – warning symbols (p.
INSTRUMENTS AND CONTROLS Eco Guide* and Power Meter* Average The average reading changes gradually according to changes in the current reading to indicate how economically the vehicle has been driven recently. The higher the average reading, the more economically the vehicle has been driven. Eco guide and Power guide are two gauges in the instrument panel that help improve driving economy.
INSTRUMENTS AND CONTROLS Utilized power The larger, lower indicator shows the amount of engine power that has been utilized2. The higher the reading on the scale, the greater the amount of power that is being utilized. The larger the gap between the two indicators, the greater the amount of power remaining.
INSTRUMENTS AND CONTROLS || Malfunction Indicator Light As you drive, a computer called On-Board Diagnostics II (OBDII) monitors your vehicle's engine, transmission, electrical and emission systems. If the indicator light remains on, the vehicle should be driven to a trained and qualified Volvo service technician for inspection, see Brakes – general (p. 269) for additional information. The malfunction indicator light will illuminate if the computer senses a condition that potentially may need correcting.
INSTRUMENTS AND CONTROLS Related information • • Information displays – introduction (p. 63) Information displays – warning symbols (p. 69) Information displays – warning symbols The warning lights alert the driver that an important function is activated or that a serious fault has occurred.
INSTRUMENTS AND CONTROLS || Engine temperature Engine overheating can result from low oil or coolant levels, towing or hard driving at high heat and altitude, or mechanical malfunction. Engine overheating will be signaled with text and a red warning triangle in the middle of the instrument display. The exact text will depend on the degree of overheating. It may range from High engine temp Reduce speed to High engine temp Stop engine.
INSTRUMENTS AND CONTROLS Reminder – doors not closed If one of the doors is not closed properly, the information or warning symbol illuminates (depending on the vehicle's speed), a graphic will be displayed in instrument panel and an explanatory text message3 will also be displayed in the instrument panel. Stop the vehicle in a safe place as soon as possible and close the door. Related information • • Information displays – introduction (p. 63) Information displays – indicator symbols (p.
INSTRUMENTS AND CONTROLS || OK/MENU: Press the button on the center console or the thumb wheel on the steering wheel keypad to select a menu alternative or to store a selected function in the system's memory. Information displays – ambient temperature sensor TUNE: Turn this control on the center console or the thumb wheel on the steering wheel keypad to navigate up/down in a menu.
INSTRUMENTS AND CONTROLS Information displays – trip odometer and clock Inserting/removing remote key Clock The trip odometers T1 and T2 and clock are displayed in the instrument panel. The remote key is used to start the engine or to use various electrical functions without starting the engine.
INSTRUMENTS AND CONTROLS || CAUTION Foreign objects in the ignition slot can impair function or cause damage. Removing the remote key The remote key can be removed from the ignition slot by pulling it out. Related information • Ignition modes (p. 74) Ignition modes The vehicle's ignition has 3 modes: 0, I, and II that can be used without starting the engine. The following table shows examples of which functions are available in the respective modes.
INSTRUMENTS AND CONTROLS Ignition mode I – With the remote key fully pressed into the ignition slot8, press START/STOP ENGINE briefly. Front seats WARNING The front seats can be adjusted in a number of ways to help provide the most comfortable seating position. • Ignition mode II – With the remote key fully pressed into the ignition slot8, press START/STOP ENGINE for approximately 2 seconds. • Returning to mode 0 To return to mode 0 from mode II or I, press START/STOP ENGINE briefly.
INSTRUMENTS AND CONTROLS Front seats – folding backrest*10 Without releasing the catches, push the backrest forward. The front passenger's seat backrest can be folded down to make it easier to transport long objects. Move the seat as far forward as possible so that the head restraint slides under the glove compartment. Return the seat to its upright position in the reverse order. WARNING • • The front passenger seat backrest can be folded to a horizontal position to make room for a long load.
INSTRUMENTS AND CONTROLS Operation Button for storing a position NOTE • Only one of the power seat's controls can be used at the same time. • The power seats have an overload protector that activates if a seat is blocked by any object. If this occurs, switch off the ignition (key in position 0) and wait for a short period before operating the seat again.
INSTRUMENTS AND CONTROLS Key memory – power driver's seat* and door mirrors Each remote key has a memory that enables it to store (remember) the position of the power driver's seat and door mirrors when the vehicle is locked with that remote key. Remote key memory and the power driver's seat* and door mirrors13 3. To activate the remote key memory feature, press ENTER (check the box). > The remote key is now ready to store the position of the power driver's seat and door mirrors.
INSTRUMENTS AND CONTROLS Returning the seat/mirrors to the stored positions To move the seat and door mirrors to the position stored in the remote key: 1. 2. Emergency stop WARNING • Unlock the driver's door with the same remote key (the one used to lock the doors). For models equipped with the optional keyless drive, you must have the same remote key in your possession. • • Open the driver's door within 2 minutes.
INSTRUMENTS AND CONTROLS || Automatically folding down the rear seat’s outboard head restraints CAUTION The rear head restraints should not be kept folded down for prolonged periods. This could result in pressure marks in leather upholstery. WARNING For safety reasons, no one should be allowed to sit in the outboard rear seat positions if the head restraints are folded down. If these positions are occupied, the head restraints should be in the upright (fixed) position.
INSTRUMENTS AND CONTROLS Rear seats – folding backrest The rear seat head restraints and backrests can be folded down. The center head restraint can be raised/lowered according to the passenger's height. CAUTION WARNING • To help avoid damage to the upholstery, there should be no objects on the rear seat and the seat belt should not be buckled when the backrest is folded down.
INSTRUMENTS AND CONTROLS Steering wheel 3. The steering wheel can be adjusted to various positions and has controls for the horn, cruise control*, menus, the infotainment system and Bluetooth®-connected cell phone. Push back the lever to lock the steering wheel in place. If the lever is difficult to push into place, press the steering wheel lightly at the same time as you push the lever. trol*, see Adaptive Cruise Control – introduction (p. 176).
INSTRUMENTS AND CONTROLS Electrically heated* steering wheel Lighting panel The steering wheel can be heated electrically. The lighting panel is used to control the daytime running lights, parking lights, etc., and to adjust the instrument panel lighting and "theater" lighting (p. 88).
INSTRUMENTS AND CONTROLS NOTE Volvo recommends the use of Daytime Running Lights in the United States. The use of these lights is mandatory in Canada. High/low beam headlights High beam flash When the engine is started, the low beams are activated automatically if the headlight control is . in position Pull the lever toward the steering wheel to position 1. The high beams come on until the lever is released.
INSTRUMENTS AND CONTROLS Active high beams (AHB)* AHB uses a camera at the upper edge of the windshield to detect the headlights of oncoming vehicles or the taillights of a vehicle directly ahead. When this happens, the headlights will automatically switch from high beams to low beams. When the camera no longer detects the headlights/taillights of other vehicles, your headlights will switch back to high beams after several seconds.
INSTRUMENTS AND CONTROLS || • • • • In bright moonlight In freezing rain In areas with dim street lighting When oncoming vehicles have dim front lighting • If there are pedestrians on or near the road • If there are reflective objects, such as signs, near the road • When oncoming vehicles' lights are obscured by e.g., fences, bushes, etc. • When there are vehicles on connecting roads • • At the top of hills or in dips in the road In sharp curves See The camera’s limitations (p.
INSTRUMENTS AND CONTROLS This function is only active in twilight or dark conditions, and only when the vehicle is in motion. If a fault should occur in the system, the symbol will illuminate and a message will be displayed as shown in the table. Symbol Auxiliary lights* and NOTE Display Explanation Headlamp failure Service required The system is not functioning properly and should be inspected/repaired by a trained and qualified Volvo service technician.
INSTRUMENTS AND CONTROLS Instrument and "theater" lighting Parking lights Instrument lighting position Turn the headlight switch to the (the license plate lighting comes on at the same time). Illumination of the display and instrument lights will vary, depending on ignition mode. The display lighting is automatically subdued in darkness and the sensitivity is set with the thumb wheel. The intensity of the instrument lighting is adjusted with the thumb wheel.
INSTRUMENTS AND CONTROLS Rear fog lights NOTE The rear fog lights are considerably brighter than the normal taillights and should be used only when conditions such as fog, rain, snow, smoke or dust reduce visibility for other vehicles to less than 500 ft. (150 meters). • • The rear fog lights are considerably brighter than the normal taillights and should be used only when conditions such as fog, rain, snow, smoke or dust reduce visibility for other vehicles to less than 500 ft. (150 meters).
INSTRUMENTS AND CONTROLS || Related information • Turn signals (p. 90) Turn signals When turning The turn signals are controlled by the left steering wheel lever. Move the lever as far up or down as possible to start the turn signals. The turn signals will be cancelled automatically by the movement of the steering wheel, or the lever can be returned to its initial position by hand.
INSTRUMENTS AND CONTROLS Front interior lighting Overhead courtesy lighting The passenger compartment lighting is switched on and off automatically when button (3) is in the neutral position. The lighting in the front part of the passenger compartment is controlled with the buttons in the ceiling console. Related information • Rear interior lighting (p.
INSTRUMENTS AND CONTROLS Home safe lighting Approach lighting When you leave your vehicle at night, you can make use of the home safe lighting function to illuminate the area in front of the vehicle. Approach lighting activates the parking lights, door mirror lights, license plate lighting, dome lighting and door step lighting when you approach the vehicle. G021150 Rear interior lighting The lights are switched on or off by pressing each respective button.
INSTRUMENTS AND CONTROLS Windshield wipers Move the lever toward the steering wheel to start the windshield and headlight washers. After the lever is released the wipers make several extra sweeps. CAUTION • Use ample washer fluid when washing the windshield. The windshield should be thoroughly wet when the wipers are in operation. • Before using the wipers, ice and snow should be removed from the windshield/ rear window. Be sure the wiper blades are not frozen in place.
INSTRUMENTS AND CONTROLS Rain sensor* The rain sensor automatically regulates wiper speed according to the amount of water on the windshield. The sensitivity of the rain sensor can be adjusted moving the thumb wheel up (the wipers will sweep the windshield more frequently) or down (the wipers will sweep the windshield less frequently). NOTE The wipers will make an extra sweep each time the thumb wheel is adjusted upward.
INSTRUMENTS AND CONTROLS the windshield is washed within a 10-minute period. • Parking lights on. Optional Active Bending Lights will be washed once for every five times the windshield is washed. Normal halogen headlights will not be washed. CAUTION • Use ample washer fluid when washing the windshield. The windshield should be thoroughly wet when the wipers are in operation. • When approx. 1 US quart (1 liter) of washer fluid remains in the reservoir, the headlights will no longer be washed.
INSTRUMENTS AND CONTROLS Power windows All power windows can be operated using the control panel in the driver's door. The control panels in the other doors only operate the window in the respective doors. WARNING • • • Always remove the ignition key when the vehicle is unattended to put the ignition in mode 0 (see Ignition modes (p. 74) for information about the ignition modes). Never leave children unattended in the vehicle.
INSTRUMENTS AND CONTROLS Sun shades Power door mirrors Retractable power door mirrors* A sun shade can be integrated into the rear parcel shelf. The control on the driver's door is used to adjust the position of the door mirrors. The mirrors can be retracted for parking/driving in narrow spaces: Integrated rear sun shade* 1. Press down the L and R buttons at the same time. 2. Release them after approximately one second. The mirrors automatically stop in the fully retracted position.
INSTRUMENTS AND CONTROLS || Tilting the door mirrors when parking* The door mirrors can be tilted down to help give the driver a better view along the sides of the vehicle, for example when parallel parking. To activate this function, select reverse gear and press the L or R mirror control button to tilt the mirror down. The function can be activated/deactivated in MY CAR under Settings Car settings Side mirror settings Tilt left mirror or Tilt right mirror. See My Car – introduction (p.
INSTRUMENTS AND CONTROLS Resetting to neutral Mirrors that have been moved out of position by an external force must be electrically reset to the neutral position for electric retracting/extending to work. • • Heated windshield*, rear window and door mirror defrosters the ignition is switched off) if the ambient temperature remains below 45 °F (7 °C). The heating function is used to defrost/de-ice the windshield and/or the rear window and door mirrors.
INSTRUMENTS AND CONTROLS Interior rearview mirror Digital compass* Calibration The interior rearview mirror has an auto-dim function that helps reduce glare from following vehicle's headlights. The rear-view mirror has an integrated display that shows the compass direction in which the vehicle is traveling.
INSTRUMENTS AND CONTROLS Press the button repeatedly until the number of the desired magnetic zone (1-15) is displayed. See the magnetic zones on the map in the following section "Selecting a magnetic zone"). 6. Wait until C is again displayed in the mirror. 7. Drive slowly in a circle at a speed of no more than 6 mph (10 km/h) until a direction is displayed. This indicates that calibration is complete. 8. Drive around in a circle an additional two times to fine-tune the calibration. 9.
INSTRUMENTS AND CONTROLS || Wind blocker Power moonroof – operation The moonroof controls are located in the ceiling console near the rearview mirror. The moonroof's sun visor opens automatically but has to be closed manually. There is a wind blocker in the moonroof's front edge. Sliding moonroof Manual opening – Pull the switch back to the first stop (the position for manual opening) and hold it until the moonroof has opened to the position of your choice.
INSTRUMENTS AND CONTROLS Automatic closing – Push the switch as far forward as possible (the position for automatic closing) and release it to automatically close the moonroof. HomeLink® Wireless Control System* – introduction Tilt position HomeLink® can be used to open garage doors, gates, etc. • • • • • During manual closing, if the moonroof is obstructed, immediately open it again. Never open or close the moonroof if it is obstructed in any way. Never allow a child to operate the moonroof.
INSTRUMENTS AND CONTROLS || WARNING • • • If you use HomeLink® to open a garage door or gate, be sure no one is near the gate or door while it is in motion. When programming a garage door opener, it is advised to park outside of the garage. Do not use HomeLink® with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982).
INSTRUMENTS AND CONTROLS 1. Position the end of your hand-held transmitter 1–3 inches (5–14 cm) away from the HomeLink button you wish to program while keeping the indicator light in view. 2. Simultaneously press and hold both the chosen HomeLink and hand-held transmitter buttons until the HomeLink indicator light changes from a slow to a rapidly blinking light. Now you may release both the HomeLink and hand-held transmitter buttons. 3.
INSTRUMENTS AND CONTROLS || Gate Operator/Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “timeout” in the same manner.
INSTRUMENTS AND CONTROLS Volvo Sensus Volvo Sensus is the core of the contact interface with your vehicle. Sensus provides information, entertainment and offers access to functions that make owning and operating a Volvo easier. Internet connected vehicle. lock and alarm functions, automatic blower speed, setting the clock, etc. Pressing the source buttons on the center con, NAV* and CAM*, sole (RADIO, MEDIA, TEL, etc.) make it possible to select e.g.
INSTRUMENTS AND CONTROLS Information display – menu controls Information display – menu overview The controls on the left steering wheel lever are used to access the menus (p. 108) that are displayed in the instrument panel (p. 63). The menus displayed depend on the current ignition mode (p. 74). The menus displayed depend on the current ignition mode (p. 74). The following menu alternatives may vary, depending on the equipment installed in the vehicle. Analog instrument panel Digital speed Trip comp.
INSTRUMENTS AND CONTROLS Information display – messages Message Description Message Description The controls on the left steering wheel lever are used to scroll among messages displayed in the instrument panel and to confirm selections. Stop engineA Stop and switch off the engine as soon as possible. Serious risk of damage. Contact an authorized Volvo workshop. Maintenance overdue If the service intervals are not followed, the warranty does not cover any damaged parts.
INSTRUMENTS AND CONTROLS Trip computer – introduction Related information The content and appearance of the trip computer varies depending on whether the vehicle is equipped with an Analog or Digital instrument panel. Digital information displays and controls Analog information display and controls The instrument panel illuminates as soon as the vehicle is unlocked and trip computer settings can be made.
INSTRUMENTS AND CONTROLS Trip computer – functions, analog instrument panel OK–press to access the trip computer's functions or acknowledge/confirm/erase a message Thumb wheel–turn to access the list of trip computer information headings and to scroll among the alternatives RESET–press to cancel/reset/exit a function after a selection has been made The trip computer has two different menu groups: • • Information display and controls Trip computer functions Trip computer information headings in the instr
INSTRUMENTS AND CONTROLS || Function Description Digital speed This displays the vehicle's speed digitally in the center of the instrument panel – km/h • Open by pressing OK, scroll using the thumb wheel, confirm by pressing OK and exit by pressing ENTER. – mph – None Trip comp. opt. – Distance to empty – Fuel consumption – Average speed – Trip odometer T1 and total dist. Selections among the trip computer information headings are made here.
INSTRUMENTS AND CONTROLS Information headings in the instrument panel Description Trip odometer T1 and total dist. • Press and hold RESET to reset trip odometer T1. Trip odometer T2 and total dist. • Press and hold RESET to reset trip odometer T2. Distance to empty See Distance to empty in Trip computer – Supplementary information (p. 116). Fuel consumption Current fuel consumption. Average speed Press and hold RESET to reset Average speed. - No information will be displayed.
INSTRUMENTS AND CONTROLS Trip computer – functions, digital instrument panel OK–press to access the trip computer's functions or to activate a selection Thumb wheel–turn to access the list of trip computer information headings and to scroll among the alternatives Ensure that none of the trip computer controls are being used in a command sequence; reset them by pressing RESET twice. 2. Press OK to open the list of functions.
INSTRUMENTS AND CONTROLS Function Description Contrast mode/Color mode Adjust the instrument panel's contrast and color. Service status Shows the number of months and mileage until the next scheduled service. Information headings 1. Three trip computer headings can be displayed at the same time; one in each of the displays (see the previous illustration). One of the combinations of information headings in the following table can be displayed. To do so: 2.
INSTRUMENTS AND CONTROLS Trip computer – Supplementary information economical driving style will generally increase this distance. General information for both Analog and Digital trip computer functions. See Economical driving (p. 284) for information about driving economically. Average fuel consumption Digital speed display* Fuel consumption since the last time this function was reset. Average speed The vehicle's average speed since the last time this function was reset.
INSTRUMENTS AND CONTROLS Trip computer – Trip statistics Settings Trip information from previous trips regarding average fuel consumption and average speed is stored and can be displayed in the form of a bar chart. Settings can be made in the MY CAR menu system as follows: Function MY CAR My S60 Trip statistics: • Trip computer – functions, digital instrument panel (p. 114) • Trip computer – Supplementary information (p. 116) • Start new trip: press ENTER to erase all pervious statistics.
CLIMATE
CLIMATE Climate – general information The vehicle is equipped with Electronic Climate Control (ECC) (p. 125) that cools, heats or dehumidifies the air in the passenger compartment. Vents in the parcel shelf NOTE The air vents at the rear of the parcel shelf should never be obstructed. Air conditioning NOTE • The air conditioning can be switched off, but to ensure the best possible climate comfort in the passenger compartment and to prevent the windows from misting, it should always be on.
CLIMATE Climate – sensors The climate system utilizes a number of sensors to help regulate the temperature and humidity level in the passenger compartment. Sensor location • The sunlight sensor is located on the top side of the dashboard. NOTE The sunlight sensor monitors which side of the car that is most exposed to sunlight. This can mean that the temperature may differ between the right and left-side air vents, even if the temperatures set for both sides of the passenger compartment are the same.
CLIMATE || NOTE Contact your Volvo retailer for IAQS air filter replacement intervals. Materials used in the cabin The materials used in the cabin have been developed to help minimize the amount of dust and make the cabin easier to keep clean. All floor mats can be easily removed for cleaning. Use car cleaning products recommended by Volvo. See also the information in Cleaning the interior (p. 363). Related information • • • Climate – general information (p. 120) Interior Air Quality System (IAQS)* (p.
CLIMATE Climate – menu settings Air distribution – general The default settings for four of the climate system's (p. 120) functions can be changed in the menu system. The incoming air is distributed through a number of different vents in the passenger compartment. • Blower speed (p. 127) in automatic mode (p. 127). • Recirculation timer (p. 130) for passenger compartment air. • • Automatic rear window defrosting (p. 99). The optional Interior Air Quality System (p. 122) (IAQS).
CLIMATE || Air vents in the door pillars Closed Open Horizontal airflow Vertical airflow Direct the outer air vents toward the side windows to defrost. Direct the vents into the passenger compartment to help maintain the desired temperature in the rear seat. Related information • • • • 124 Climate – general information (p. 120) Air distribution – table (p. 131) Air distribution – recirculation (p. 130) Max. defroster and electrically heated windshield* (p.
CLIMATE Electronic climate control (ECC) ECC (Electronic Climate Control) helps maintain the selected temperature in the passenger com- partment and the temperature can be set separately on the driver's and passenger's sides. Temperature control (p. 127), driver's side Heated front passenger's seat* (p. 126) Heated driver's seat* (p. 126) Temperature control (p. 127), passenger's side Defroster (maximum effect), electrically heated windshield* (p. 128) Recirculation (p. 130) Blower (p.
CLIMATE Heated seats Lowest heat level – one indicator light. The front seat heating has three levels to increase comfort for the driver and passenger in cold weather. If no indicator lights are illuminated, the seat heating is switched off. The rear outboard seat heating has three levels to increase comfort for the passengers in cold weather. Heated front seats* Related information • • Climate – general information (p. 120) Electronic climate control (ECC) (p.
CLIMATE Temperature and blower control NOTE When the vehicle is started, the most recent setting is resumed. The blower should always be activated to help avoid condensation and fogging on the windows. Temperature control The temperatures on the driver and passenger sides can be set separately. NOTE Heating or cooling cannot be speeded up by selecting a higher/lower temperature than the actual temperature required.
CLIMATE Air conditioning The air conditioning function cools and dehumidifies the air in the passenger compartment. When the indicator light in the button is on, the air conditioning is controlled automatically. This cools/heats and dehumidifies the incoming air. When the indicator light in the button is off, the air conditioning is disengaged. Other functions are still controlled automatically. When maximum defroster (p.
CLIMATE NOTE • Triangular areas at the far sides of the windshield are not heated electrically and will take slightly longer to defrost/de-ice. • The heated windshield may affect the performance/range of e.g., transponders used to automatically pay highway tolls or other communication equipment. Air distribution – function The air distribution function consists of three buttons.
CLIMATE Air distribution – recirculation Recirculation can be used to shut out exhaust fumes, smoke, etc., from the passenger compartment. The air in the passenger compartment is then recirculated, i.e., no air from outside the car is taken into the car when this function is activated. The indicator light in the button will illuminate when recirculation is selected. If the air in the car recirculates for too long, there is a risk of condensation forming on the insides of the windows, especially in winter.
CLIMATE Air distribution – table Air distribution (p. 123) is selected using the buttons in the center console climate panel. Air distribution Use Air distribution Use Air to windows. Some air flows from the dashboard air vents. The air is not recirculated. Air conditioning is always engaged. To remove de-fog/deice the front side windows and windshield quickly. Air to the floor and windows. Some air flows from the dashboard air vents.
CLIMATE || 132 Related information • • • Climate – general information (p. 120) Air distribution – function (p. 129) Max. defroster and electrically heated windshield* (p. 128) * Option/accessory, for more information, see Introduction.
LOADING AND STORAGE
LOADING AND STORAGE Storage spaces The following is an overview of the storage compartments in the passenger compartment.
LOADING AND STORAGE Compartment in door panel Storage pocket on the front edge of the front seat cushions Glove compartment (p. 137) Storage compartment Storage compartment (p. 136), 12-volt socket (p. 136) and AUX input/USB connector Rear seat cup holders Storage pocket Related information • • Vanity mirror (p. 137) 12-volt socket in the trunk* (p. 137) * Option/accessory, for more information, see Introduction.
LOADING AND STORAGE Tunnel console Tunnel console – 12-volt sockets The tunnel console is located between the front seats. The electrical sockets can be used for 12-volt accessories such as cell phone chargers and coolers. For the socket to supply current, the ignition must be in at least mode I (p. 74). The sockets are located between the cup holders in the tunnel console and on the rear side of the tunnel console (p. 136) for rear seat passengers.
LOADING AND STORAGE Glove compartment Vanity mirror 12-volt socket in the trunk* The glove compartment provides a lockable storage compartment for small items. The vanity mirrors are located on the upper side of the sun visors. This 12-volt socket can be used e.g., to connect the tire sealing system's compressor (certain models) and other 12-volt accessories. The owner's manual and maps can be kept here. There are also holders for pens and fuel cards.
LOADING AND STORAGE Loading – general WARNING The load carrying capacity of your vehicle is determined by factors such as the number of passengers, the amount of cargo, the weight of any accessories that may be installed, etc. • • To increase loading space, the rear seat backrests can be folded down, see Rear seats – folding backrest (p. 81).
LOADING AND STORAGE Removal: – Open the cover 30 degrees and lift straight up. Loading – roof load carriers Using load carriers Installation: Load carriers are available as Volvo accessories. Observe the following points when in use: – • To avoid damaging your vehicle and to achieve maximum safety when driving, we recommend using the load carriers that Volvo has developed especially for your vehicle.
LOADING AND STORAGE || • • The vehicle's wind resistance and fuel consumption will increase with the size of the load. Drive smoothly. Avoid rapid starts, fast cornering and hard braking. Related information • • Loading – general (p. 138) Load anchoring eyelets (p. 140) Load anchoring eyelets WARNING The load anchoring eyelets on both sides of the vehicle are used to fasten straps, etc., to help anchor items in the trunk.
LOADING AND STORAGE Grocery bag holder The grocery bag holder holds shopping bags in place. Grocery bag holder under the floor of the trunk The grocery bag holder holds shopping bags in place. 1. Open the hatch in the floor of the trunk. 2. Secure the shopping bags with the strap. Related information • Loading – general (p.
LOCKS AND ALARM
LOCKS AND ALARM Remote key and key blade Remote key – loss Two remote keys are provided with your vehicle. They enable you to unlock the doors and trunk, and also function as ignition keys to start the vehicle or operate electrical components. The remote keys contain detachable metal key blades for manually locking or unlocking the driver's door and the glove compartment. The visible ends of these key blades are unique to make it easier to identify "your" remote key.
LOCKS AND ALARM Related information • Remote key – functions (p. 147) Key memory NOTE The memory in the remote key makes it possible to store certain personal settings. The position of the side door mirrors, power driver's seat* and the selected instrument panel theme1 are stored in the remote keys when the vehicle is locked.
LOCKS AND ALARM Locking/unlocking confirmation Settings can be made in the menu system for audible and visual confirmation when the vehicle has been locked or unlocked. With these functions activated, the following will occur when the vehicle is locked/unlocked: Locking confirmation • The turn signals flash once, an audible signal sounds and the door mirrors will fold* in. Confirmation will only be given when all doors and the trunk are properly closed and locked.
LOCKS AND ALARM Message Meaning Insert car key Remote key not recognized during start. Try to start the vehicle again. Car key not found Vehicles with keyless drive* only. Remote key not recognized during start. Try to start the vehicle again.
LOCKS AND ALARM || Unlock – Press the Unlock button on the remote once to unlock the driver's door. After a short pause, press the Unlock button a second time within 10 seconds to unlock the other doors and the trunk. This function can be changed so that all doors unlock at the same time by pressing My Car and going to Settings Car settings Lock settings Change doors unlock setting. For a description of the menu system, see My Car – introduction (p. 71).
LOCKS AND ALARM Detachable key blade – general information Detachable key blade – detaching/ reinserting Each remote key contains a detachable metal key blade (p. 144) for mechanically locking or unlocking the driver's door and the glove compartment, and to enable the valet locking (p. 150) function. The key blades have a unique code, which is used if new ones need to be produced. This code is available at an authorized Volvo retailer. The detachable key blade (p.
LOCKS AND ALARM Detachable key blade – unlocking Your vehicle's remote key (p. 144) contains a metal, detachable key blade that can be used to unlock the driver's door, lock the glove compartment, etc. 3. Insert the key blade as far as possible in the driver's door lock. Turn the key blade to unlock the driver's door. This will trigger the alarm. 4. To turn off the alarm, insert the remote key in the ignition slot. This also applies to vehicles equipped with the optional keyless drive. 5.
LOCKS AND ALARM Activating the valet locking function Remote key – replacing the battery The remote key can be opened if the battery needs to be replaced. G021084 The battery should be replaced if: • • • The engine can be started The glove compartment cannot be unlocked Access to the trunk is blocked (the trunk lid cannot be unlocked or opened with the remote, and the rear seat backrests cannot be lowered The information symbol illuminates and Low battery in remote control. Please change batteries.
LOCKS AND ALARM || Opening the remote key To open the remote key NOTE Slide the spring loaded catch to the side. Volvo recommends that the batteries used in the remote control meet the UN Manual of Test and Criteria, Part III, sub-section 38.3. Pull the key blade straight out of the remote key. Batteries installed in the key from the factory and batteries exchanged by an authorized Volvo workshop fulfill the above criteria.
LOCKS AND ALARM Keyless drive*– locking/unlocking This system makes it possible to unlock and lock the vehicle without having to press any buttons on the remote key. It is only necessary to have a keyless drive remote key in your possession to operate the central locking system. Both of the remote keys provided with the vehicle have the keyless function, and additional ones can be ordered. The system can accommodate up to six remote keys.
LOCKS AND ALARM || Related information • Alarm indicator (p. 162) Keyless drive* – unlocking with key blade If the remote key does not function normally (weak battery, etc.), the vehicle can be unlocked with the detachable key blade. 3. Insert the key blade as far as possible in the driver's door lock. Turn the key blade to unlock the driver's door. This will trigger the alarm. 4. To turn off the alarm, insert the remote key in the ignition slot.
LOCKS AND ALARM Keyless drive* – key memory NOTE When you leave the vehicle with a remote key in your possession and lock any door, the position of the driver's seat2 and door mirrors will be stored in the remote key's memory. If the vehicle is locked by pressing the button on one of the door handles or by pressing the lock button on the remote key, or if it is left unlocked for more than 30 minutes, the key memory function will be deactivated.
LOCKS AND ALARM • • CAUTION Tested To Comply With FCC Standards Keyless drive* – antenna locations Keyless drive remote keys should never be left in the vehicle. In the event of a break-in, a remote found in the vehicle could make it possible to start the engine. For Automobile Use The keyless drive system has a number of antennas located at various points in the vehicle. Electromagnetic fields or metal obstructions can interfere with the keyless drive system.
LOCKS AND ALARM WARNING People with implanted pacemakers should not allow the pacemaker to come closer than 9 inches (22 cm) to any of the keyless drive system's antennas. This is to help prevent interference between the pacemaker and the keyless drive system. Related information • Keyless drive*– locking/unlocking (p. 153) Locking/unlocking – from the outside The remote key (p. 144) is used to lock/unlock all of the doors and the trunk at the same time.
LOCKS AND ALARM Manual locking In the horizontal position, the door cannot be opened from the outside. In certain situations (e.g., if there is no electrical current in the vehicle), the doors can be locked manually. In the vertical position, the door can be opened from the inside and the outside. The detachable key blade (p. 149) can be used in the lock cylinder in the driver's door to lock that door. NOTE If the manual child safety lock (p.
LOCKS AND ALARM Unlocking The vehicle can be unlocked from inside the vehicle in two ways: • • By pressing the unlock button . The front doors can be unlocked and opened by pulling the door handle once. The rear doors can be unlocked by pulling the door handle once and opened by pulling the handle again. Locking • Press the lock button doors have been closed. after the front • : all of the doors • Press the lock button that are closed will lock.
LOCKS AND ALARM Locking/unlocking – glove compartment The glove compartment can only be locked and unlocked using the detachable key blade in the remote key. For information on removing the key blade from the remote key, see Detachable key blade – detaching/reinserting (p. 149). Locking/unlocking – trunk The trunk can be locked, unlocked and opened in several ways. The alarm indicator (p. 162) light on the dashboard will stop flashing to indicate that the alarm is not monitoring the entire vehicle.
LOCKS AND ALARM Opening the trunk manually The alarm indicator on the dashboard will begin flashing to show that the vehicle is locked and that the alarm has been armed. NOTE • • The trunk is held closed by an electronic locking mechanism. To open: 1. Press lightly on the rubberized plate under the handle to release the lock. 2. Lift the handle to open the trunk lid.
LOCKS AND ALARM Alarm – general information NOTE The alarm system provides a warning if an attempt is made to break into the vehicle. The alarm is automatically armed (p. 163) whenever the vehicle is locked with the remote key. When armed, the alarm continuously monitors a number of points on the vehicle. The following conditions will trigger the alarm: • • • • • The hood is forced open. Related information • • • Alarm – turning off (p. 164) Alarm signal (p. 163) Alarm indicator (p.
LOCKS AND ALARM Alarm – arming/disarming The alarm system provides a warning if an attempt is made to break into the vehicle. Disarming the alarm – Arming the alarm – Press the Lock button on the remote key. One long flash of the turn signals will confirm that the alarm (p. 162) is armed. Alarm confirmation settings can be changed in MY CAR, under Car settings Lock settings Keyless entry. For a description of the menu system, see My Car – introduction (p. 71).
LOCKS AND ALARM Alarm – turning off Alarm-related functions 3. The alarm system provides a warning if an attempt is made to break into the vehicle. The following is general information regarding the alarm system in your vehicle. Related information If the alarm is sounding, it can be stopped by pressing the Unlock button on the remote key or by inserting the remote key in the ignition slot. Two short flashes from the car's turn signals confirm that the alarm has been turned off.
DRIVER SUPPORT
DRIVER SUPPORT Active chassis* (Four C) Active chassis, Four-C (Continuously Controlled Chassis Concept), regulates the characteristics of the shock absorbers so that the vehicle's driving characteristics can be adjusted. There are three settings: Comfort, Sport and Advanced. Operation Sport In this mode, the vehicle's body sway is reduced during cornering and steering response is more immediate. The transmission shifts up at higher rpm for sportier driving.
DRIVER SUPPORT Spin Control (SC) The SC function is designed to help prevent the drive wheels from spinning while the vehicle is accelerating. Active Yaw Control (AYC) This function helps maintain directional stability, for example when cornering, by braking one or more of the wheels if the vehicle shows a tendency to skid or slide laterally.
DRIVER SUPPORT || 168 Related information • • Stability system – introduction (p. 166) Stability system – symbols and messages (p.
DRIVER SUPPORT Stability system – symbols and messages Symbols and messages in the main instrument panel A text message can be erased by pressing briefly the OK button on the turn signal lever. Symbol Message Description ESC Temporarily OFF The ESC system function has been temporarily reduced due to high brake disc temperature. The function reactivates automatically when the brakes have cooled. ESC Service required The ESC system is not functioning properly.
DRIVER SUPPORT || Symbol Message Description Flashing symbol. ESC is actively functioning to help counteract wheel spin and/or a skid. Steady glow. Sport mode has been activated. Please note that ESC is not deactivated at this time but its functionality is reduced. WARNING The stability system is intended to help improve driving safety. It supplements, but can never replace, the driver's judgment and responsibility when operating the vehicle.
DRIVER SUPPORT Adjustable steering force* Steering force increases with the speed of the vehicle to give the driver enhanced sense of control and stability. At low speed the vehicle is easy to steer in order to facilitate parking, etc. Adjustable steering force* Road Sign Information (RSI)* – introduction RSI is a feature that helps the driver see road signs with the posted speed limit. Introduction Related information • Road Sign Information (RSI) – operation (p.
DRIVER SUPPORT Road Sign Information (RSI) – operation Displaying the speed limit indication can be deactivated. To do so: • Deselect the alternative in MY CAR Settings Car settings Road Sign Information or cancel by pressing EXIT. Speed alert The driver can opt to be alerted if the vehicle exceeds the posted speed limit by more than 3 mph (5 km/h). The alert is given when the symbol with the posted speed limit in the instrument panel begins to flash.
DRIVER SUPPORT Cruise control (CC) – introduction Cruise control is designed to assist the driver by maintaining a set speed. It is primarily intended for use on long straight roads in steady traffic, such as on highways and other main roads. Operation Related information • Cruise control (CC) – engaging and setting speed (p. 173) • Cruise control (CC) – deactivating (p. 175) Cruise control (CC) – engaging and setting speed Cruise control is designed to assist the driver by maintaining a set speed.
DRIVER SUPPORT || Before a speed can be set, the cruise control system must be engaged (put in standby mode). 2. Press the CRUISE button (1). > The symbol illuminates and the text (---) mph (5) indicates that cruise control is in standby mode. – NOTE • NOTE Putting cruise control in standby mode does not set a cruising speed. Setting a speed • Use the or buttons set the vehicle's current speed. The set speed is shown in the display.
DRIVER SUPPORT the previous section "Turning ACC off completely." The next time the system is switched on, ACC will be reactivated. Related information • • Adaptive Cruise Control – introduction (p. 176) Adaptive Cruise Control – function (p. 177) Cruise control (CC) – deactivating Cruise control is designed to assist the driver by maintaining a set speed. It is primarily intended for use on long straight roads in steady traffic, such as on highways and other main roads.
DRIVER SUPPORT Adaptive Cruise Control – introduction ACC is an optional system designed to assist the driver by maintaining a set speed or a set time interval to the vehicle ahead. It is primarily intended for use on long straight roads in steady traffic, such as on highways and other main roads.
DRIVER SUPPORT Radar sensor type approval USA FCC ID: L2C0038TR Canada IC: 3432A-0038TR This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
DRIVER SUPPORT || to maintain a 2-second interval will vary according the speed of the vehicles. WARNING • • • Adaptive Cruise Control is not a collision avoidance system. The driver is always responsible for applying the brakes if the system does not detect another vehicle. Adaptive Cruise Control does not react to people or animals, or small vehicles such as bicycles and motorcycles. It also does not react to slow moving, parked or approaching vehicles, or stationary objects.
DRIVER SUPPORT WARNING Adaptive Cruise Control only warns of vehicles detected by the radar sensor, see Adaptive Cruise Control – limitations (p. 186). In some cases there may be no warning or the warning may be delayed. The driver should always apply the brakes when necessary. Adaptive Cruise Control – engaging NOTE The driver's door must be closed and the driver's seat belt must be fastened before ACC can be put in active mode.
DRIVER SUPPORT Adaptive Cruise Control – setting speed This symbol indicates that you are approaching a vehicle ahead. Setting a speed NOTE cle. When this happens, a speed range will be indicated on the speedometer: The higher speed (the currently set speed (5)) will be marked in green. The lower speed in the range is the speed of the vehicle ahead.
DRIVER SUPPORT Adaptive Cruise Control – setting time interval Setting a time interval Different time intervals can be selected and are shown in the instrument panel2 as 1–5 horizontal bars. The greater the number of bars, the longer the time interval. One bar represents a time interval of approximately 1 second; 5 bars is approximately 3 seconds.
DRIVER SUPPORT || WARNING The vehicle may accelerate quickly after has been pressed if its current speed is considerably lower than the set speed. Standby mode due to action by the driver ACC is temporarily deactivated and put in standby mode: • • • if the brakes are applied if the gear selector is moved to N if the driver drives faster than the set speed for more than 1 minute. In this happens, the driver will have to regulate the vehicle's speed.
DRIVER SUPPORT Adaptive Cruise Control – passing another vehicle Adaptive Cruise Control (ACC) – Queue Assist Passing another vehicle Queue Assist is an added ACC feature that is linked to your vehicle's automatic transmission. If your vehicle’s speed is being regulated by ACC and the driver indicates that he/she would like to pass the vehicle ahead by using the left turn signal, ACC can assist by accelerating briefly. This function is active at speeds above approximately 45 mph (70 km/h).
DRIVER SUPPORT || The driver will then have to reactivate ACC in one of the following ways: • • Automatic standby mode when ACC changes target vehicles other type of object such as e.g., a speed bump. • By pressing By accelerating up to at least 3 mph (4 km/h). ACC will then resume following the vehicle ahead. No automatic braking when at a standstill Your vehicle will then resume following the vehicle ahead at the set time interval.
DRIVER SUPPORT • • • ACC has kept the vehicle at a standstill for more than 2 minutes The engine has been switched off The brakes have overheated Related information • Adaptive Cruise Control – introduction (p. 176) Radar sensor rain, or if snow or other objects are obscuring the radar sensor. The radar sensor is designed to help detect cars or larger vehicles driving in the same direction as your vehicle, in the same lane. NOTE Keep the area in front of the radar sensor clean.
DRIVER SUPPORT Adaptive Cruise Control – limitations WARNING • The ACC cannot cover all driving situations and traffic, weather and road conditions. Situations where ACC may not function optimally • WARNING • • The radar sensor has a limited field of vision. In some situations it may detect a vehicle later than expected or not detect other vehicles at all. If ACC is not functioning properly, cruise control will also be disabled.
DRIVER SUPPORT WARNING • • • Adaptive Cruise Control is not a collision avoidance system. The driver is always responsible for applying the brakes if the system does not detect another vehicle. Adaptive Cruise Control does not react to people or animals, or small vehicles such as bicycles and motorcycles. It also does not react to slow moving, parked or approaching vehicles, or stationary objects.
DRIVER SUPPORT Adaptive Cruise Control – symbols and messages Symbols and messages in the display A text message can be erased by pressing briefly on the OK button on the turn signal lever. Symbol Message Description Green symbol A speed has been set. White symbol ACC is in standby mode but no speed has been set. - Standard cruise control has been selected manually.
DRIVER SUPPORT Symbol - - Message Description Cruise control Service required ACC is not functioning. Press Brake To hold + an audible signal The vehicle is at a standstill and ACC will release the brakes before the parking brake engages to keep the vehicle stopped but a problem with the parking brake means that the vehicle may begin to roll. Contact a trained and qualified Volvo service technician. The driver will have to apply the brakes.
DRIVER SUPPORT Adaptive Cruise Control – troubleshooting If the message Radar blocked See manual is displayed, this means that the radar signals from tem with Auto-brake and Pedestrian Detection will not function. This, in turn, means that the functions of the ACC, Distance Alert, and Collision Warning Sys- The table lists possible causes for this message being displayed, and suitable actions. Cause Action The surface of the radar in the grille is dirty or obstructed in some way.
DRIVER SUPPORT Distance Alert – introduction NOTE Distance Alert is part of Adaptive Cruise Control and is a function that provides information about the time interval to the vehicle ahead. Distance Alert only monitors distance to the vehicle ahead while Adaptive Cruise Control is in standby mode or off. Distance Alert – operation Distance Alert is part of Adaptive Cruise Control and is a function that provides information about the time interval to the vehicle ahead.
DRIVER SUPPORT || Setting a time interval NOTE • The higher your vehicle’s speed, the greater the distance to the vehicle ahead, measured in feet (meters), for a given time interval. • The set time interval is also used by Adaptive Cruise Control, see Adaptive Cruise Control – setting speed (p. 180). WARNING Only use a time interval that is suitable in current traffic conditions.
DRIVER SUPPORT Related information • • • Distance Alert – introduction (p. 191) Distance Alert – operation (p. 191) Distance Alert – symbols and messages (p.
DRIVER SUPPORT Distance Alert – symbols and messages Symbols and text messages Distance Alert is part of Adaptive Cruise Control and is a function that provides information about the time interval to the vehicle ahead. Symbol Message Description Radar blocked See manual Distance Alert has been temporarily disconnected because the radar is obstructed in some way and cannot detect other vehicles. See Adaptive Cruise Control – limitations (p. 186) for information on the radar sensor’s limitations.
DRIVER SUPPORT City Safety – introduction City Safety™4 is a support system designed to help the driver avoid low speed collisions when driving in slow-moving, stop-and-go traffic. City Safety™ is not active if your vehicle’s speed is below approximately 2 mph (4 km/h). This means that City Safety™ will not react if your vehicle approaches another vehicle at very low speed, for example, when parking.
DRIVER SUPPORT • City Safety – symbols and messages (p. 200) • City Safety – Laser sensor (p. 201) City Safety – function display to indicate that the system is/has been active. Function NOTE • When City Safety™ applies the brakes, the brake lights will illuminate. • In cases where City Safety™ has stopped the vehicle, the system will then release the brakes. The driver must apply the brakes to keep the vehicle at a standstill.
DRIVER SUPPORT City Safety – operation Using City Safety™ NOTE The City Safety™ function is activated automatically each time the engine has been switched off and restarted. On and Off In certain situations, it may be desirable to switch City Safety™ off, such as when driving in close quarters where leaves, branches, etc. may obscure the hood and windshield.
DRIVER SUPPORT || may not be detected. Normally, the license plate and taillight reflectors give the rear section of a vehicle ahead sufficient reflective surfaces to be detected. NOTE • Keep the windshield in front of the laser sensor free of ice, snow, dirt, etc., see City Safety – function (p. 196). • Snow or ice on the hood deeper than 2 inches (5 cm) may obstruct the sensor. Keep the hood free of ice and snow.
DRIVER SUPPORT • • • City Safety – limitations (p. 197) • City Safety – Laser sensor (p. 201) City Safety – operation (p. 197) City Safety – symbols and messages (p.
DRIVER SUPPORT City Safety – symbols and messages instrument panel may illuminate and its associated message will be displayed. Symbols and messages in the display A text message can be erased by pressing briefly on the OK button on the turn signal lever. When City Safety™ automatically applies the brakes, one or more of the symbols in the main Symbol Message Meaning/action required Auto braking by City Safety City Safety™ is applying/has applied the brakes automatically.
DRIVER SUPPORT City Safety – Laser sensor The laser sensor Maximum pulse energy Maximum average output Pulse length Divergence (horizontal × vertical) WARNING 2.64 μJ Eye injury may occur if any of the following points are not followed: 45 mW 33 ns • 28° × 12° NOTE The function of aftermarket laser detectors may be affected by City Safety's laser sensor.
DRIVER SUPPORT • • City Safety – troubleshooting (p. 198) Collision warning – introduction City Safety – symbols and messages (p. 200) Pedestrian and Cyclist Detection with Full Auto Brake is designed to assist the driver if there is a risk of a collision with a pedestrian, a cyclist, a vehicle ahead that is at a standstill or one that is moving in the same direction as your vehicle.
DRIVER SUPPORT WARNING • • • • WARNING • Pedestrian and Cyclist Detection with Full Auto Brake does not work in all driving, traffic, weather and road conditions. It does not react to vehicles not traveling in the same direction as your vehicle. Pedestrian and Cyclist Detection with Full Auto Brake does not react to animals. Warnings are only provided when the risk of collision is high.
DRIVER SUPPORT Collision warning* – function Brake Support If the risk of collision continues to increase after the collision warning has been given, Brake Support is activated. Brake Support prepares the brake system to react quickly, and the brakes are applied slightly. This may be experienced as a light tug. If the brakes are applied quickly, full braking effect will be provided.
DRIVER SUPPORT Collision warning* – operation Settings are made by pressing MY CAR on the center console control panel and using the menus displayed. Activating/deactivating both warning signals To switch the system's audible and visual signals on or off at the same time, press MY CAR on the center console control panel and go to Settings Car settings Driver support systems Collision Warning.
DRIVER SUPPORT || Related information • • • Collision warning – introduction (p. 202) Collision warning* – function (p. 204) Collision warning* – Cyclist detection The system can detect a cyclist and auto-brake if certain parameters are fulfilled. Collision warning* – Pedestrian detection (p. 207) • Collision warning* – Cyclist detection (p. 206) • • • Collision warning* – limitations (p. 208) • Collision warning – troubleshooting (p. 211) The camera’s limitations (p.
DRIVER SUPPORT • The camera's function is deactivated and will not detect a cyclist in darkness or in tunnels, even if there is street lighting in the area. • For optimal cyclist detection, City Safety™ must be activated. WARNING • Collision warning* – Pedestrian detection (p. 207) • • • Collision warning* – limitations (p. 208) Collision warning* – Pedestrian detection Collision warning – troubleshooting (p. 211) Collision warning – symbols and messages (p.
DRIVER SUPPORT || body and the person must be at least 32 in. (80 cm) tall. • The system cannot detect a pedestrian carrying a large object. • The camera's capacity to see a pedestrian at dawn or dusk is limited, much as it is for the human eye. • The camera's function is deactivated and will not detect a pedestrian in darkness or in tunnels, even if there is street lighting in the area.
DRIVER SUPPORT WARNING • • • • In certain situations, the system cannot provide warnings or warnings may be delayed if traffic conditions or other external factors make it impossible for the radar sensor or camera to detect a pedestrian, a cyclist or a vehicle ahead. Warnings may not be provided if the distance to the vehicle ahead is short, or if movements of the steering wheel/brake pedal are great, such as during active driving.
DRIVER SUPPORT The camera’s limitations WARNING The camera has the same limitations as the human eye. • The camera is used by Pedestrian and Cyclist Detection with Full Auto Brake Collision warning – introduction (p. 202), Active High Beams (Active high beams (AHB)* (p. 85)), Road Sign Information (Road Sign Information (RSI)* – introduction (p. 171)) and Driver Alert System (Driver Alert System (p. 215)) with Lane Departure Warning or Lane Keeping Aid.
DRIVER SUPPORT Collision warning – troubleshooting Fault tracing and actions obscured and cannot detect pedestrians, cyclists, vehicles or road marker lines in front of the vehicle. If the message Windscreen Sensors blocked is displayed, this means that the camera is This, in turn, means that Pedestrian and Cyclist Detection with Full Auto Brake, Driver Alert Con- trol, Lane Departure Warning or Lane Keeping Aid will not have full functionality.
DRIVER SUPPORT || Maintenance • Collision warning* – Cyclist detection (p. 206) • • • Collision warning* – limitations (p. 208) The camera’s limitations (p. 210) Collision warning – symbols and messages (p. 213) Camera and radar sensor6. In order to function properly, the camera and radar sensor must be kept clean. Dirt, ice, snow, etc., will reduce the function of these components. Remove ice and snow when necessary and wash these areas regularly with a suitable car washing liquid.
DRIVER SUPPORT Collision warning – symbols and messages A text message can be erased by pressing briefly on the OK button on the turn signal lever. The table lists possible causes for collision warning-related messages being displayed, and suitable actions. Symbol Message Description Collis'n warning OFF Pedestrian and Cyclist Detection with Full Auto Brake is switched off. This message is displayed when the engine is started and will disappear after approx. 5 seconds.
DRIVER SUPPORT || 214 Related information • • • • Collision warning – introduction (p. 202) Collision warning* – function (p. 204) Collision warning* – operation (p. 205) Collision warning* – Pedestrian detection (p. 207) • Collision warning* – Cyclist detection (p. 206) • • Collision warning* – limitations (p. 208) Collision warning – troubleshooting (p. 211) * Option/accessory, for more information, see Introduction.
DRIVER SUPPORT Driver Alert System The Driver Alert System is designed to help a driver who may be becoming fatigued or who is inadvertently leaving the lane. Introduction The Driver Alert System consists of two different functions that can be switched on together or separately. • Driver Alert Control (DAC), see Driver Alert Control (DAC) – introduction (p. 215) • Lane Departure Warning (LDW)7, see Lane Departure Warning (LDW) – introduction (p.
DRIVER SUPPORT || NOTE The camera has certain limitations, see Adaptive Cruise Control – limitations (p. 186). WARNING • • • DAC is not intended to extend the duration of driving. Always plan breaks at regular intervals to help remain alert. A warning from DAC should not be ignored. A driver may not be aware of how fatigued he/she has become. In certain cases, fatigue may not affect the driver’s behavior. In situations of this type, no warning will be provided.
DRIVER SUPPORT Driver Alert Control (DAC) – function • Function • • Driver Alert is activated when the vehicle exceeds a speed of 40 mph (65 km/h) and will remain active as long as the speed is over approx. 37 mph (60 km/h). If the vehicle is being driven erratically, the driver will be alerted by an audible signal and the message Driver Alert Time for a break is displayed. The warning will be repeated after a short time if the driving pattern remains the same. Press the OK button to erase a message.
DRIVER SUPPORT || 218 • Lane Departure Warning (LDW) – introduction (p. 221) • Lane Keeping Aid (LKA) – introduction (p.
DRIVER SUPPORT Driver Alert Control (DAC) – symbols and messages Depending on the situation, DAC may display certain symbols and text messages in the instrument panel or center console screen. Symbols and messages Instrument panel Symbol Message Description Driver Alert Time for a break The vehicle has been driven erratically. The driver receives an audible signal and a text message. Windscreen Sensors blocked The camera is temporarily not functioning, due to snow, ice, or dirt on the windshield.
DRIVER SUPPORT || Center console display Symbol Message Description - Driver Alert OFF The function is not switched on. - Driver Alert Available The function is active. - Driver Alert Standby <65 km/h The function has gone into standby mode because the vehicle's speed is below 40 mph (65 km/h). - Driver Alert Unavailable The camera is temporarily not functioning, due to snow, ice, or dirt on the windshield. Clean the area of the windshield in front of the camera.
DRIVER SUPPORT Lane Departure Warning (LDW) – introduction Related information • • The LDW function is designed to help reduce the risk of accidents in situations where the vehicle unintentionally leaves its lane and there is a risk of driving off the road or into the opposite lane. Lane Departure Warning (LDW)9 Your vehicle may be equipped with Lane Departure Warning (LDW) or Lane Keeping Aid (LKA), depending on your choice of engine.
DRIVER SUPPORT Lane Departure Warning (LDW) – operation WARNING The driver will only be warned once for each time the wheels cross a marker line. No alarm will be given if a marker line is between the wheels. Operation and function Settings Settings for Lane Departure Warning can be made in the menu system by pressing My Car. Go to Settings Car settings Driver support systems Lane Departure Warning.
DRIVER SUPPORT • Lane Departure Warning (LDW) – introduction (p. 221) Lane Departure Warning (LDW) limitations • Lane Departure Warning (LDW) - limitations (p. 223) Limitations • Lane Departure Warning (LDW) – introduction (p. 221) The camera used by LDW has the same limitations as the human eye. See The camera’s limitations (p. 210) for more information about the camera's limitations.
DRIVER SUPPORT Lane Departure Warning (LDW) – symbols and messages Symbols and messages A text message can be erased by pressing briefly on the OK button on the turn signal lever. Symbol 224 Message Description Lane departure warning ON/ Lane departure warning OFF The function is switched on or off. The text disappears after 5 seconds. - Lane Depart Warn Available The function is monitoring the road’s marker lines. - Lane Depart.
DRIVER SUPPORT Related information • Lane Departure Warning (LDW) – operation (p. 222) • • Driver Alert System (p. 215) • Lane Departure Warning (LDW) – introduction (p. 221) Lane Departure Warning (LDW) - limitations (p.
DRIVER SUPPORT Lane Keeping Aid (LKA) – introduction Related information • • • Lane Keeping Aid (LKA) – limitations (p. 229) LDW or LKA • Lane Keeping Aid (LKA) – symbols and messages (p. 230) • The camera’s limitations (p. 210) Your vehicle may be equipped with Lane Departure Warning (LDW) or Lane Keeping Aid (LKA), depending on your choice of engine.
DRIVER SUPPORT Lane Keeping Aid (LKA) – operation Depending on the number of optional features installed in the vehicle, there may not be space for the On/Off button on the center console. If this is the case, LKA can be switched on or off in the MY CAR menu system. LKA is active at speeds above 40 mph (65 km/h) on highways or other major roads with clearly marked side/lane marker and center lines. On narrow roads where the distance between side/ lane marker lines is less than approximately 8.5 feet ( 2.
DRIVER SUPPORT || Steering assist LKA attempts to keep the vehicle within the lane's side marker lines. Vibration warnings LKA provides vibrations in the steering wheel and steering assistance11. LKA provides steering assistance If the vehicle approaches one of the lane's side marker lines and the turn signals are not being used, LKA will attempt to steer the vehicle back into the lane. If the vehicle crosses a marker line, LKA provides a warning in the form of vibrations in the steering wheel.
DRIVER SUPPORT Lane Keeping Aid (LKA) – limitations The camera used by LKA has the same limitations as the human eye. See The camera’s limitations (p. 210) for more information about the camera's limitations. NOTE Related information • • • • Driver Alert System (p. 215) Lane Keeping Aid (LKA) – introduction (p. 226) Lane Keeping Aid (LKA) – operation (p. 227) Lane Keeping Aid (LKA) – symbols and messages (p. 230) In certain cases, it may be difficult for LKA to assist the driver correctly.
DRIVER SUPPORT Lane Keeping Aid (LKA) – symbols and messages A text message can be erased by pressing briefly on the OK button on the turn signal lever. Symbol Message Description - Lane Keeping Aid Unavailable at this speed The function has gone into standby mode because the vehicle's speed is below 40 mph (65 km/h). - Lane Keeping Aid Unavailable for current markings The road lacks clear marker lines or the camera is not functioning properly. See The camera’s limitations (p.
DRIVER SUPPORT Park assist – introduction The park assist system is designed to assist you when driving into parking spaces, garages, etc. An audible signal and symbols in the audio system’s display indicate the distance to the object. • Rear Park Assist Camera (PAC) – function (p.
DRIVER SUPPORT || Audible signal The Park Assist system uses an intermittent tone that pulses faster as you come close to an object, and becomes constant when you are within approximately 1 ft (30 cm) of an object in front of or behind the vehicle. If there are objects within this distance both behind and in front of the vehicle, the tone alternates between front and rear speakers. Rear park assist NOTE The level of the audible signal can be lowered/raised with the infotainment volume control.
DRIVER SUPPORT Front park assist The distance monitored in front of the vehicle is approximately 2.5 ft (0.8 m). The audible signal comes from the audio system's front speakers. It may not be possible to combine auxiliary headlights and front park assist since these lights could trigger the system's sensors. NOTE • Rear Park Assist Camera (PAC) – function (p. 240) Park assist – operation Function Park assist and CTA* button The system is activated automatically when the vehicle is started.
DRIVER SUPPORT || Activating/deactivating The system is activated automatically when the vehicle is started. – Press the Park assist button on the center console to temporarily deactivate the system(s). > The indicator light in the button will go out when the system has been deactivated. Park assist – limitations Cleaning the sensors The sensors must be cleaned regularly to ensure that they work properly. Clean them with water and a suitable car washing detergent.
DRIVER SUPPORT Park Assist Pilot (PAP)* – introduction NOTE If a trailer hitch is configured in the vehicle's electrical system, PAP will take the trailer hitch into consideration when determining the necessary size of a parking space. The Park Assist Pilot provides assistance when parallel parking by measuring the parking space and turning the steering wheel. Introduction WARNING • • PAP does not function in all situations and is only intended to assist the driver when parallel parking.
DRIVER SUPPORT || 1. Searching for and measuring a parking space. While this is taking place, the vehicle's speed must be below 20 mph (30 km/h). See also steps A and B in the illustration in the section "1: Searching and measuring" in Park Assist Pilot (PAP)* – operation (p. 236). 2. Steering the vehicle as it backs into the parking space. See also steps C and D in the illustration in the section "2: Backing into the parking space" in Park Assist Pilot (PAP)* – operation (p. 236). 3.
DRIVER SUPPORT 2: Backing into the parking space NOTE • Release the wheel while PAP is steering the vehicle. • The steering wheel must be able to turn freely. • For PAP to function optimally, wait until the steering wheel is no longer turning before beginning the next phase of the parking procedure. 3: Adjusting the vehicle's position When the vehicle is backing up, PAP will steer it into the parking space. 1.
DRIVER SUPPORT Park Assist Pilot (PAP)* – limitations • The PAP parking procedure will be cancelled if. • The vehicle's speed goes above approximately 4 mph 7 km/h • • The driver moves the steering wheel If the stability or ABS systems are activated (e.g., if a wheel starts to spin because of a slippery road surface If the system has been switched off, this will be indicated by a text message in the instrument panel.
DRIVER SUPPORT The sensors must be cleaned regularly to ensure that they work properly. Clean them with water and a suitable car washing detergent. Related information • Park Assist Pilot (PAP)* – introduction (p. 235) • • • Park Assist Pilot (PAP)* – function (p. 235) • • Park Assist Pilot (PAP)* – operation (p. 236) Park Assist Pilot (PAP)* – symbols and messages (p. 239) Park assist – introduction (p. 231) Rear Park Assist Camera (PAC) – introduction (p.
DRIVER SUPPORT Rear Park Assist Camera (PAC) – introduction WARNING • The Park Assist Camera is designed to provide the driver with a view of the area behind the vehicle when backing up. Introduction • PAC uses the display in the center console to show the area behind the car while you are backing up.
DRIVER SUPPORT Ambient lighting conditions The camera automatically monitors the ambient lighting conditions behind the vehicle and constantly adjusts sensitivity to light. This may cause the brightness and quality of the image on the screen to vary slightly. Sensitivity to light is increased in dark conditions or in bad weather, which may affect image quality.
DRIVER SUPPORT || Deactivation Move the gear selector from R to another gear. The camera remains active for approx. 5 seconds after the gear selector has been moved from R or until the vehicle's forward speed exceeds 6 mph/10 km/h (21 mph/35 km/h in reverse). The screen will then revert to the view that was displayed before R was selected. NOTE If any button on the center console control panel is pressed, the camera image will disappear from the display.
DRIVER SUPPORT WARNING Keep in mind that the image on the screen only shows the area behind the vehicle. The driver must always watch for people, animals, other vehicles, etc., near the sides of the vehicle when turning while backing up. 10.5 ft (3.2 m) behind the bumper if there are no objects in the way. Vehicles equipped with Park Assist Related information • Rear Park Assist Camera (PAC) – operation (p. 241) • Rear Park Assist Camera (PAC) – limitations (p.
DRIVER SUPPORT Rear Park Assist Camera (PAC) – limitations Limitations Even if a fairly small section of the screen image appears to be obstructed, this may mean that a relatively large area behind the vehicle is hidden and objects there may not be detected until they are very near the vehicle. BLIS* – introduction Bicycle carriers or other accessories mounted on the trunk may obstruct the camera's field of view. • • Rear Park Assist Camera (PAC) – introduction (p.
DRIVER SUPPORT WARNING • • • BLIS and CTA are information systems, NOT warning or safety systems and do not function in all situations. BLIS and CTA do not eliminate the need for you to visually confirm the conditions around you, and the need for you to turn your head and shoulders to make sure that you can safely change lanes or back up. As the driver, you have full responsibility for changing lanes/backing up in a safe manner.
DRIVER SUPPORT || • • WARNING BLIS* – operation • BLIS does not function in sharp curves. BLIS does not function when your vehicle is backing up. Activating/deactivating BLIS When BLIS is deactivated/reactivated, the indicator lights will go out/illuminate (the indicators will also flash once when the function is reactivated) and a message will appear in the instrument panel. Related information • • • • • BLIS* – introduction (p. 244) • BLIS* – Cross Traffic Alert (CTA) (p.
DRIVER SUPPORT BLIS* – Cross Traffic Alert (CTA) Cross Traffic Alert (CTA) is a supplementary BLIS15 function intended to detect vehicles crossing behind your vehicle while you are backing up. WARNING • • • BLIS and CTA are information systems, NOT warning or safety systems and do not function in all situations.
DRIVER SUPPORT || Examples of other limitations include: The vehicle is pulled far into a parking space CTA's blind area CTA's "field of vision" • Dirt, ice or snow obstructing the sensors may reduce the system's function or make it impossible to detect other vehicles or objects. • Do not attach tape, decals, etc., on the surface of the sensors (see the illustration in the following "Maintenance" section).
DRIVER SUPPORT The BLIS/CTA16 sensors are located on the inside of the rear fenders/bumper. The surfaces in front of the sensors must be kept clean for the system to function optimally. CAUTION Repairs to the BLIS/CTA systems and/or repainting the rear bumper should only be done by a trained and qualified Volvo service technician. Related information • • • • • BLIS* – introduction (p. 244) BLIS* – function (p. 245) BLIS* – operation (p. 246) BLIS* – Cross Traffic Alert (CTA) (p.
STARTING AND DRIVING
STARTING AND DRIVING Starting the engine The engine can be started/switched off using the remote key and the START/STOP ENGINE button. WARNING • • Ignition slot with remote key inserted (see Ignition modes (p. 74) for more information on ignition modes) 1. Press the remote key into the ignition slot as far as possible, with the metallic key blade pointing outward (not inserted into the slot)1. 2. Depress the brake pedal2.
STARTING AND DRIVING WARNING • • • • CAUTION • Always remove the remote key from the ignition slot when leaving the vehicle and ensure that the ignition in mode 0 (see Ignition modes (p. 74) for information about the ignition modes). On vehicles with the optional keyless drive, never remove the remote key from the vehicle while it is being driven or towed. Always place the gear selector in Park and apply the parking brake before leaving the vehicle.
STARTING AND DRIVING Engine Remote Start (ERS)* – introduction WARNING Keep the following in mind before using ERS: ERS is a feature that makes it possible to remotely start the engine using the remote key to cool or heat the passenger compartment before driving. • • • The climate system will start using automatic settings. When the engine is started using ERS, it will run for a maximum of 15 minutes before automatically switching off again.
STARTING AND DRIVING 1. The turn signals will flash several times. 2. The engine will start. Engine Remote Start (ERS)* – switching off the engine 3. The turn signals will illuminate for 3 seconds to indicate that the engine has started. Any of the following will switch off the engine if it has been started with ERS: After the engine has started, the vehicle remains locked but the alarm is disarmed.
STARTING AND DRIVING 3. 4. Fold back the cover over the positive (+) terminal on your vehicle's battery (2), marked with a "+" sign, located under a folding cover. • Connect the black jumper cable to the auxiliary battery's negative (–) terminal (3) and to the ground point in your vehicle's engine compartment (right engine mount at the top, on the outer screw) (4). 5. Start the engine in the assisting vehicle, then start the engine in the vehicle with dead battery. 6.
STARTING AND DRIVING CAUTION The transmission’s temperature is monitored to help prevent damage to the transmission or other drivetrain components. If there is a risk of overheating, the warning symbol on the instrument panel will illuminate and a text message will be displayed. Follow the instructions provided there.
STARTING AND DRIVING || Neutral: position N Transmission – Geartronic No gear is engaged and the engine can be started with the gear selector in this position. Apply the parking brake if the vehicle is stationary with the gear selector in position N. In order to move the gear selector from the N position, the brake pedal must be depressed and the ignition must be in at least mode II. Geartronic allows you to manually shift among your vehicle's forward gears.
STARTING AND DRIVING While driving • If you select the manual shifting position while driving, the gear that was being used in the Drive position will also initially be selected in the manual shifting position. • Move the gear selector forward (toward +) to shift to a higher gear or rearward (toward –) to shift to a lower gear. • If you hold the gear selector toward "–", the transmission will downshift one gear at a time and will utilize the braking power of the engine.
STARTING AND DRIVING || • during active driving (e.g., on a winding road, while accelerating, etc) • if the gear selector was in S when the paddles were activated NOTE • If the transmission reverts to D, the paddles will have to be reactivated (pull either paddle toward the steering wheel and release it) before they can be used to shift gears again.
STARTING AND DRIVING Transmission – shiftlock override If the vehicle cannot be driven, for example because of a dead battery, the gear selector must be moved from the P position before the vehicle can be moved8. Shiftlock override Related information • • • • Transmission – general information (p. 256) Transmission – positions (p. 257) Transmission – Geartronic (p. 258) Fuel tank volume – specification and volume (p.
STARTING AND DRIVING Start/Stop – introduction Start/Stop is a function that temporarily switches off the engine when the vehicle is not moving, for instance in heavy traffic or at a traffic light to help reduce fuel consumption. Start/Stop is available with certain engines/ transmissions. Start/Stop – function Function and use restarts. If the ECO function* is activated, the engine may autostop before the vehicle comes to a complete standstill. Start/Stop – function (p. 262) Start/Stop – settings (p.
STARTING AND DRIVING Related information • • • • • • Start/Stop – introduction (p. 262) Start/Stop – settings (p. 265) Start/Stop – Auto-stop exceptions (p. 263) Start/Stop – Auto-stop exceptions Condition/situation In certain situations or conditions, the engine may not auto-stop when the vehicle comes to a standstill, such as if: The road's incline is very steep. A trailer's electrical system is connected to the vehicle. Start/Stop – Auto-start exceptions (p.
STARTING AND DRIVING Start/Stop – Auto-start exceptions Condition/situation In certain situations or conditions, the engine may auto-start even though the driver is still pressing the brake pedal, such as if: The gear selector is moved from D to SB, R or "+/–". The driver's door is opened with the gear selector in D – an audible signal and a text message will inform the driver that Start/Stop is active. Condition/situation Condensation forms on the windows.
STARTING AND DRIVING Start/Stop – settings Settings for the Start/Stop function can be made in the MY CAR menu system. Related information • • • • • • Start/Stop – introduction (p. 262) Start/Stop – function (p. 262) Start/Stop – Auto-stop exceptions (p. 263) Start/Stop – Auto-start exceptions (p. 264) Start/Stop – Hill Start Assist (HSA) (p. 261) Start/Stop – symbols and messages (p.
STARTING AND DRIVING Start/Stop – symbols and messages Text messages certain situations. Follow the instructions provided in the message. The following table gives several examples. Combined with the information symbol in the instrument panel, the Start/Stop function may also display messages in Symbol Message Information/action Auto Start/Stop Service required Start/Stop is not functioning properly. Contact a Volvo retailer or a trained and qualified Volvo service technician.
STARTING AND DRIVING ECO* NOTE function10 Eco is a developed by Volvo to give the driver the opportunity to actively drive more economically and to help reduce fuel consumption. When Eco is activated, several climate system parameters are changed and the function of certain current-consuming systems will be reduced. Introduction Some of these functions can be restarted manually but full functionality will not be restored until Eco is deactivated.
STARTING AND DRIVING || This feature is primarily intended to be used in driving situations where a decrease in speed is expected, such as when entering a zone with a lower speed limit. Eco Coast enables proactive driving with as little braking as possible.
STARTING AND DRIVING All Wheel Drive (AWD) NOTE Your Volvo can be equipped with permanent All Wheel Drive, which means that power is distributed automatically between the front and rear wheels. The message AWD disabled Service required will be appear in the information display if an electrical fault should occur in the AWD system. A warning light will also illuminate in the instrument panel. If this occurs, have the system checked by a trained and qualified Volvo service technician.
STARTING AND DRIVING || Brake pad inspection On vehicles equipped with a jack*, the condition of the brake pads can be checked by raising the vehicle (see Changing a wheel – removing wheel (p. 295) for information about using the jack and removing a wheel) and performing a visual inspection of the brake pads. WARNING • • • If the vehicle has been driven immediately prior to a brake pad inspection, the wheel hub, brake components, etc., will be very hot.
STARTING AND DRIVING Related information • • • • Parking brake – general information (p. 273) Emergency Brake Assistance (EBA) (p. 272) Brakes – general (p. 269) Brakes – symbols Anti-lock braking system (ABS) Symbols in the instrument panel Specification The ABS system helps to improve vehicle control (stopping and steering) during severe braking conditions by limiting brake lockup. Steady glow – Check the brake fluid level.
STARTING AND DRIVING Brake lights Emergency Brake Assistance (EBA) The brake lights come on automatically when the brakes are applied. EBA is designed to provide full brake effect immediately in the event of sudden, hard braking. Adaptive brake lights The adaptive brake lights activate in the event of sudden braking or if the ABS system is activated. This function causes an additional taillight on each side of the vehicle to illuminate to help alert vehicles traveling behind.
STARTING AND DRIVING Parking brake – general information Low battery voltage The electric parking brake helps to keep the vehicle stationary when it is parked. If the battery voltage is too low, the parking brake cannot be applied or released. Connect an auxiliary battery if the battery voltage is too low, see Jump starting (p. 255).
STARTING AND DRIVING || NOTE • In an emergency the parking brake can be applied when the vehicle is moving by holding in the control. Braking will be interrupted when the accelerator pedal is depressed or the control is released. • An audible signal will sound during this procedure if the vehicle is moving at speeds above 6 mph (10 km/h). Parking brake – releasing Releasing the electric parking brake Related information • • • Parking brake – releasing (p. 274) • Brakes – general (p.
STARTING AND DRIVING • Parking brake – symbols and messages (p. 276) • Brakes – general (p.
STARTING AND DRIVING Parking brake – symbols and messages A text message can be erased by pressing briefly on the OK button on the turn signal lever. Symbol and messages in the instrument panel Symbol Message Description/action "Message" Read the message in the information display A flashing symbol indicates that the parking brake is being applied. If the symbol flashes in any other situation then this means that a fault has arisen. Read the message on the information display.
STARTING AND DRIVING Driving through water CAUTION The vehicle should be driven with extreme caution if it is necessary to drive through standing water. The vehicle can be driven through water up to a depth of approximately 10 in. (25 cm), (S60 Cross Country: approximately 12 in. (30 cm)) at walking speed to help prevent water from entering the differential and the transmission. Water reduces the oil's lubricating capacity and may shorten the service life of these components.
STARTING AND DRIVING Conserving electrical current Before a long distance trip • Keep the following in mind to help minimize battery drain: It is always worthwhile to have your vehicle checked by a trained and qualified Volvo service technician before driving long distances. Your retailer will also be able to supply you with bulbs, fuses, spark plugs and wiper blades for your use in the event that problems occur. • • • • • 278 When the engine is not running, avoid using ignition mode II.
STARTING AND DRIVING Driving in cold weather Check your vehicle before the approach of cold weather. The following advice is worth noting: • Make sure that the engine coolant (p. 333) contains 50 percent antifreeze. Any other mixture will reduce freeze protection. This gives protection against freezing down to –31 °F (–35 °C). The use of "recycled" antifreeze is not approved by Volvo. Different types of antifreeze must not be mixed.
STARTING AND DRIVING cle inspection programs will make detection of misfueling easier, possibly resulting in emission test failure for misfueled vehicles. NOTE Some U.S. and Canadian gasolines contain an octane enhancing additive called methylcyclopentadienyl manganese tricarbonyl (MMT). If such fuels are used, your Emission Control System performance may be affected, and the Check Engine Light (malfunction indicator light) located on your instrument panel may light.
STARTING AND DRIVING lished by leading automotive manufactures to meet the needs of today’s advanced engines. Qualifying gasoline retailers (stations) will, in most cases, identify their gasoline as having met the “TOP TIER Detergent Gasoline” standards. NOTE Information about TOP TIER Detergent Gasoline is available at www.toptiergas.com.
STARTING AND DRIVING Refueling – opening/closing fuel filler door The fuel filler door is located on the right rear fender (indicated by an arrow beside the fuel ) tank symbol on the information display locking button does not lock the fuel filler door. 1. Open the side hatch in the trunk (on the same side as the fuel filler door). • Be sure the fuel filler door is not obstructed and is completely closed after refueling. 2. Grasp the handle on the green cord.
STARTING AND DRIVING Refueling – opening/closing fuel cap • If necessary, the fuel filler door can be opened manually. Opening/closing the fuel cap • CAUTION Emission controls Do not refuel with the engine running12. Turn the ignition off or to position I. If the ignition is on, an incorrect reading could occur in the fuel gauge. • Keep your engine properly tuned.
STARTING AND DRIVING || nents, altering emission system components or location or removing components, and/or repeated use of leaded fuel. NOTE Unleaded fuel is required for vehicles with three-way catalytic converters. Heated oxygen sensors The heated oxygen sensors monitor the oxygen content of the exhaust gases. Readings are fed into a control module that continuously monitors engine functions and controls fuel injection.
STARTING AND DRIVING Some of the above mentioned items and others are checked at the standard maintenance intervals. capacity weight or maximum permissible axle loads are not exceeded. • WARNING Driving with the trunk open: Driving with the trunk open could lead to poisonous exhaust gases entering the passenger compartment.
STARTING AND DRIVING || 286 • If the automatic transmission begins to overheat, a message will be displayed in the text window. • • Avoid overload and other abusive operation. • It is necessary to balance trailer brakes with the towing vehicle brakes to provide a safe stop (check and observe state/local regulations). • Do not connect the trailer's brake system directly to the vehicle's brake system. • More frequent vehicle maintenance is required.
STARTING AND DRIVING WARNING • • • • Bumper-attached trailer hitches must not be used on Volvos, nor should safety chains be attached to the bumper. Trailer hitches attaching to the vehicle rear axle must not be used. Never connect a trailer's hydraulic brake system directly to the vehicle brake system, nor a trailer's lighting system directly to the vehicle lighting system. Consult your nearest authorized Volvo retailer for correct installation.
STARTING AND DRIVING Towing the vehicle CAUTION Always check with state and local authorities before attempting to tow another vehicle because this type of towing is subject to regulations regarding maximum towing speed, length and type of towing device, lighting, etc. 1. 2. General towing precautions: With the remote key fully pressed into the ignition slot14, press START/STOP ENGINE for approximately 2 seconds to activate ignition mode II.
STARTING AND DRIVING Attaching the towing eyelet WARNING The towing eyelet is located under the floor of the trunk. This eyelet must be screwed into the positions provided on the right sides of either the front or rear bumper (see illustration). • There are two different types of covers over the openings for the towing eyelet and they have to be opened differently. • • If the cover has a notch, insert a coin, etc., into the notch and pry open the edge of the cover.
STARTING AND DRIVING || CAUTION • The vehicle should always be towed in the forward direction. • Vehicles with All Wheel Drive (AWD)* that are being towed with the front wheels off the ground should not be towed at a speed above approx. 45 mph (70 km/h) and should not be towed farther than 30 miles (50 km). Related information • 290 Towing eyelet (p. 288) * Option/accessory, for more information, see Introduction.
WHEELS AND TIRES
WHEELS AND TIRES Tires – general information Your vehicle is equipped with tires according to the vehicle's tire information placard on the Bpillar (the structural member at the side of the vehicle, at the rear of the driver's door opening). Introduction CAUTION Some Volvo models are equipped with an Ultra High Performance tire and wheel combination designed to provide maximum dry pavement performance with consideration for hydroplaning resistance.
WHEELS AND TIRES Tires – storage and age When storing complete wheels (tires mounted on rims), they should be suspended off the floor or placed on their sides on the floor. New Tires accelerate the aging process. The temporary spare1 should also be replaced at 6-year intervals, even if it has never been used. WARNING • A tire's age can be determined by the DOT stamp on the sidewall (see the illustration). A tire with e.g., visible cracks or discoloration should be replaced immediately.
WHEELS AND TIRES • Tires – tread wear indicator The letters TWI are printed on the side of the tire. When approximately 1/16" (1.6 mm) is left on the tread, these strips become visible and indicate that the tire should be replaced. Tires with less than 1/16" (1.6 mm) tread offer very poor traction. When replacing worn tires, it is recommended that the tire be identical in type (radial) and size as the one being replaced.
WHEELS AND TIRES Changing a wheel – direction of rotation Related information Incorrectly mounted tires impair the car's braking properties and ability to force aside rain, snow and slush. • • • Tire specifications (p. 302) Tires – storage and age (p. 293) Changing a wheel – removing wheel Wheel changes should always be carried out correctly. Tires – tread wear indicator (p. 294) G021778 Summer and winter tires The jack*, towing eyelet and tools* are stowed under the floor of the trunk.
WHEELS AND TIRES || 3. Lug wrench and towing eyelet Tool for removing the plastic covers on the wheel nuts Remove the wheel cover (where applicable) using the removal tool or remove the wheel cover by hand. 4. Block the wheels that are on the ground with wooden blocks or large stones. 5. Screw the towing eyelet into the lug wrench as shown in the illustration. CAUTION The towing eyelet must be screwed into the lug wrench as far as possible. 6.
WHEELS AND TIRES 7. There are two jack attachment points on each side of the vehicle. Position the jack under the attachment point to be used on a level, firm, non-slippery surface and crank it up until it is correctly aligned and seated in the attachment point. Before raising the vehicle, check that the jack is still correctly positioned in the attachment. • 8. Raise the vehicle until the wheel to be changed is lifted off the ground. • 9. Unscrew the wheel nuts completely and remove the wheel.
WHEELS AND TIRES Changing a wheel – spare wheel Related information Wheel changes should always be carried out correctly. Spare tire • Changing a wheel – installing a wheel (p. 299) • Changing a wheel – removing wheel (p. 295) A spare tire can be purchased for your vehicle as an accessory. Follow the instructions included with the spare tire regarding use and stowing in the vehicle. See also Changing a wheel – removing wheel (p. 295) for additional information.
WHEELS AND TIRES Changing a wheel – accessing the spare wheel 7. The following procedure explains how to access the spare wheel (where applicable). 1. Release the bag's retaining straps. 2. Lift the bag out of the vehicle and remove the spare wheel from the bag. 3. Fold up the floor hatch in the trunk. 4. Remove the jack* and tools* from the foam block and change the wheels (see the instructions in the following section "Changing a wheel"). 5.
WHEELS AND TIRES || 5. Press the plastic covers onto the wheel nuts and Install the wheel cover (where applicable). The opening in the wheel cover for the tire's inflation valve must be positioned over the valve. Tire inflation – general information NOTE Check tire inflation pressure regularly. Related information Changing a wheel – spare wheel (p. 298) Changing a wheel – removing wheel (p.
WHEELS AND TIRES WARNING • • Under-inflation is the most common cause of tire failure and may result in severe tire cracking, tread separation, or "blow-out," with unexpected loss of vehicle control and increased risk of injury. Under-inflated tires reduce the load carrying capacity of your vehicle. When weather temperature changes occur, tire inflation pressures also change. A 10-degree temperature drop causes a corresponding drop of 1 psi (7 kPa) in inflation pressure.
WHEELS AND TIRES || tion pressure table or see the inflation pressure placard. Related information • • • Tire specifications (p. 302) Tires – storage and age (p. 293) Tires – tread wear indicator (p. 294) Tire specifications Information on the sidewall The following information can be found on a tire's sidewall.
WHEELS AND TIRES 1. 215: the width of the tire (in millimeters) from sidewall edge to sidewall edge. The larger the number, the wider the tire. 2. 65: The ratio of the tire's height to its width in percent. 3. R: Radial tire (the designation RF and the symbol indicate that the vehicle is equipped with optional self-supporting run flat tires4. 4. 15: The diameter of the wheel rim (in inches). 5. 95: The tire's load index.
WHEELS AND TIRES Loading specifications Properly loading your vehicle will provide maximum return of vehicle design performance. Before loading your vehicle, familiarize yourself with the following terms for determining your vehicle's weight ratings, with or without a trailer, from the vehicle's Federal/Canadian Motor Vehicle Safety Standards (FMVSS/CMVSS) label, and the vehicle's tire information placard: NOTE • The location of the various labels in your vehicle, see Label information (p. 368).
WHEELS AND TIRES 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. WARNING • • Exceeding the permissible axle weight, gross vehicle weight, or any other weight rating limits can cause tire overheating resulting in permanent deformation or catastrophic failure.
WHEELS AND TIRES perature is normally reached after the vehicle has been parked for at least 3 hours. Tire specifications – Uniform Tire Quality Grading ALL PASSENGER VEHICLE TIRES MUST CONFORM TO FEDERAL SAFETY REQUIREMENTS IN ADDITION TO THESE GRADES. Quality grades can be found, where applicable, on the tire sidewall between the tread shoulder and maximum section width.
WHEELS AND TIRES WARNING The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, under-inflation, or excessive loading, either separately or in combination, can cause heat buildup and tire failure. Snow chains CAUTION Snow chains can be used on your Volvo with the following restrictions: • • • • • • Snow chains should be installed on front wheels only. Use only Volvo approved snow chains.
WHEELS AND TIRES Snow tires/studded tires5 Owners who live in or regularly commute through areas with sustained periods of snow or icy driving conditions are strongly advised to fit suitable winter tires to help retain the highest degree of traction. Tires for winter use: • It is important to install winter tires on all four wheels to help retain traction during cornering, braking, and accelerating. Failure to do so could reduce traction to an unsafe level or adversely affect handling.
WHEELS AND TIRES system that illuminates a low tire pressure telltale ( ) when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure.
WHEELS AND TIRES || NOTE The system indicates low tire pressure but does not replace normal tire maintenance. For information on correct tire pressure, please refer to the tire inflation decal on the driver's door opening or consult your Volvo retailer. Related information • • 310 Tire pressure monitoring - overview (p. 308) Calibrating Tire Monitor In order for Tire Monitor to work correctly, tire pressure reference values must be set. This must be done each time wheels or tire pressures are changed.
WHEELS AND TIRES Tire Monitor status information ment panel ( ) is illuminated: the system is temporarily unavailable. It should become operational again shortly. The current status of the system and the tires is indicated by color-coded graphics. This status can be displayed by pressing the MY CAR button on the center console and going to Settings Car settings Tire monitoring.
WHEELS AND TIRES || NOTE To help avoid incorrect tire inflation pressure, only inflate the tires when they are cold. The tires are considered to be cold when they have the same temperature as the surrounding (ambient) air. This temperature is normally reached after the vehicle has been parked for at least 3 hours. After driving a distance of approximately 1 mile (1.6 km), the tires are considered to be hot.
WHEELS AND TIRES Tire Pressure Monitoring System (TPMS) – changing wheels Please keep the following in mind when changing or replacing the factory installed TPMS wheels/tires on the vehicle: • Not all aftermarket wheels are equipped with TPMS sensors in the valves. • If the vehicle is equipped with a temporary spare tire, this tire does not have a TPMS sensor.
WHEELS AND TIRES Tire Pressure Monitoring System (TPMS) – recalibrating After adjusting inflation pressure, repeat steps 1-5 above. Tire Pressure Monitoring System (TPMS) – activating/deactivating In certain cases, it may be necessary to recalibrate TPMS to conform to Volvo's recommended tire inflation pressures (see the tire inflation decal on the driver's door opening), for example, if higher inflation pressure is necessary when transporting heavy loads.
WHEELS AND TIRES Tire Pressure Monitoring System (TPMS) – messages NOTE • Erasing warning messages When a low tire pressure warning message has been displayed and the tire pressure warning light in the instrument panell ( ) has come on: 1. Use a tire pressure gauge to check the inflation pressure of all four tires. 2. Re-inflate the tire(s) to the correct pressure (consult the tire pressure decal on the driver's door opening). 3.
WHEELS AND TIRES Tire sealing system* – general information The vehicle is equipped with a tire sealing system that enables you to temporarily seal a hole in the tread surface and re-inflate a flat tire, or to adjust a tire’s inflation pressure. The 12-volt sockets are located in the front tunnel console and on the rear side of the center console in the rear seat. Accessing the tire sealing system The tire sealing system is stowed under the floor of the trunk. To access it: 1.
WHEELS AND TIRES Tire sealing system–temporarily repairing a flat tire NOTE Do not remove any foreign objects (nails, etc.) from the tire before using the sealing system. • Stage 2: The tire’s inflation pressure is checked and adjusted if necessary. Tire sealing system* – overview The vehicle is equipped with a tire sealing system that enables you to temporarily seal a hole in the tread surface and re-inflate a flat tire, or to adjust a tire’s inflation pressure.
WHEELS AND TIRES || Bottle with sealing compound Air pressure gauge • WARNING Please keep the following points in mind when using the tire sealing system: • • The sealing compound bottle (no. 8 in the illustration) contains 1) rubber latex, natural and 2) ethanediol. These substances are harmful if swallowed. • The contents of this bottle may cause allergic skin reactions or otherwise be potentially harmful to the respiratory tract, the skin, the central nervous system, and the eyes.
WHEELS AND TIRES Tire sealing system* – sealing a hole The tire sealing system can be used to temporarily seal a hole in the tread surface of a tire. NOTE Do not break the seal on the bottle. This occurs automatically when the bottle is screwed into the holder. Stage 1: Sealing the hole 1. Peel off the speed limit sticker and affix it to the steering wheel hub where it will be clearly visible to the driver. 2.
WHEELS AND TIRES || WARNING • • • Never stand next to the tire being inflated when the compressor is in operation. If cracks, bubbles, etc. form on the tire, switch off the compressor immediately. If there is visible damage to the sidewall or the rim, the tire cannot be repaired. The vehicle should not be driven if this occurs. Contact a towing service or Volvo On Call Roadside Assistance if applicable.
WHEELS AND TIRES WARNING If heavy vibrations, unsteady steering behavior, or noises should occur while driving, reduce speed and park the vehicle in a safe place. Recheck the tire for bumps, cracks, or other visible damage, and recheck its inflation pressure. If the pressure is below 19 psi (1.3 bar), do not continue driving. Have the vehicle towed to a trained and qualified Volvo service technician.
WHEELS AND TIRES WARNING • • The vehicle’s engine should be running when the tire sealing system is used to avoid battery drain. Therefore, be sure the vehicle is parked in a well ventilated place, or outdoors, before using the system. The parking brake should be securely applied and the gear selector should be in the P (park) position. Children should never be left unattended in the vehicle when the engine is running. 7. Check the tire’s inflation pressure on the gauge.
MAINTENANCE AND SERVICING
MAINTENANCE AND SERVICING Maintenance – introduction Periodic maintenance will help keep your vehicle running well. Introduction The maintenance services contain several checks that require special instruments and tools and therefore must be performed by a qualified technician. To keep your Volvo in top condition, specify time-tested and proven Genuine Volvo Parts and Accessories. The Federal Clean Air Act – U.S.
MAINTENANCE AND SERVICING Maintenance – owner maintenance Periodic maintenance requirements and intervals are described in your vehicle's Warranty and Service Records Information booklet. The following points can be carried out between the normally scheduled maintenance services. dirt, and corrosion that can be caused by salt residues. Clean leaves and twigs from air intake vents at the base of the windshield, and from other places where they may collect.
MAINTENANCE AND SERVICING Maintenance – hoisting When the vehicle is hoisted, the jack or garage lift must be positioned in the correct lifting points. Hoisting the vehicle If a garage jack is used to lift the vehicle, it should be placed: Front: under either of the two reinforced areas under the front section of the vehicle, not under to jack attachment points (the outermost points shown in the illustration). Rear: Under the jack attachment points.
MAINTENANCE AND SERVICING Onboard Diagnostic System OBD II is part of your vehicle's computerized engine management system. It stores diagnostic information about your vehicle's emission controls. It can light the Check Engine light (MIL) if it detects an emission control "fault." A "fault" is a component or system that is not performing within an expected range. A fault may be permanent or temporary. OBD II will store a message about any fault.
MAINTENANCE AND SERVICING || CSB menu access On-screen service messages Once the prerequisites have been established, all CSB-related menus can be accessed in MY CAR by pressing OK/MENU and then selecting Maintenance & repair. vehicle's instrument panel will also be turned off remotely by Volvo. • No: No other messages will be displayed on the Sensus screen but the Service Reminder Light on the vehicle's instrument panel will stay on.
MAINTENANCE AND SERVICING retailer can access or search for this information using your vehicle's VIN number. This number can be found in your warranty booklet or on the dashboard at the lower left corner of the windshield. – Select Maintenance & repair vehicle data. Send Maintenance – opening/closing hood The hood is opened by first releasing the lock from the passenger compartment and then pressing the release control. WARNING Check that the hood locks properly when closed.
MAINTENANCE AND SERVICING Engine compartment – overview WARNING The overview shows the main inspection points in the engine compartment. The cooling fan (located at the front of the engine compartment, behind the radiator) may start or continue to operate (for up to 6 minutes) after the engine has been switched off. WARNING Before performing any operations in the engine compartment, the ignition should always be completely switched off (in mode 0, see Ignition modes (p.
MAINTENANCE AND SERVICING CAUTION • The oil level on 4-cylinder engines is checked electronically and is checked using a dipstick on 5- and 6-cylinder engines. Not checking the oil level regularly can result in serious engine damage if the oil level becomes too low. • Oil that is lower than the specified quality can damage the engine. Checking the engine oil (5- and 6cylinder engines) • Volvo does not recommend the use of oil additives.
MAINTENANCE AND SERVICING || G021737 Electronic oil level sensor (4-cylinder engines only) The oil level must be between the MIN and MAX marks on the dipstick Checking the oil 1. Pull out the dipstick and wipe it with a lintfree rag. 2. Reinsert the dipstick, pull it out, and check the oil level. The level must be between the MIN and MAX marks. 3. Add oil if necessary. If the level is close to the MIN mark, add approximately 0.5 US quarts (0.5 liters) of oil. 4.
MAINTENANCE AND SERVICING CAUTION • If Oil service required is displayed, the oil level may be too high. Take the vehicle to an authorized Volvo workshop as soon as possible. • If the oil level sensor indicates that the level is too low, using the correct oil, top up with the amount of oil indicated as soon as possible, see oil specifications (p. 376). WARNING Do not allow oil to spill onto or come into contact with hot exhaust pipe surfaces.
MAINTENANCE AND SERVICING CAUTION 334 • If necessary, top up the cooling system with Volvo Genuine Coolant/Antifreeze only (a 50/50 mix of water and antifreeze). • Different types of antifreeze/coolant may not be mixed. • If the cooling system is drained, it should be flushed with clean water or premixed anti-freeze before it is refilled with the correct mixture of water/anti-freeze.
MAINTENANCE AND SERVICING Checking the level The fluid reservoir is concealed under the round cover at the rear of the engine compartment. The round cover must be removed first before the reservoir cap can be accessed. Check, without removing the cap, that there is sufficient fluid in the reservoir. Filling 1. Turn and open the cover. Engine compartment – power steering fluid 2. The fluid level must be between the MIN and MAX marks.
MAINTENANCE AND SERVICING CAUTION Keep the area around the power steering fluid reservoir clean when checking. Bulbs – introduction NOTE Certain bulbs can be replaced by the vehicle's owner. However, the bulbs on the following list should only be replaced by a trained and qualified Volvo service technician. • For information regarding any bulbs not mentioned in this section, please contact your Volvo retailer or a trained and authorized Volvo service technician.
MAINTENANCE AND SERVICING WARNING • • The engine should not be running when changing bulbs. If the engine has been running just prior to replacing bulbs in the headlight housing, please keep in mind that components in the engine compartment will be hot. Bulbs – headlight housing The entire headlight housing must be lifted out when replacing all front bulbs. CAUTION When disconnecting the connector, pull on the connector itself and not on the wiring.
MAINTENANCE AND SERVICING || 2. Reinstall the headlight housing and locking pins. The short locking pin should be closest to the grille. Check that they are correctly inserted. The headlight housing must be properly in place and the wiring connector correctly reconnected before the lighting is switched on or the remote key is inserted into the ignition slot. 3. Bulbs – cover The larger cover has to be removed in order to change the high/low beam headlight bulbs.
MAINTENANCE AND SERVICING Bulbs – low beam, Halogen Bulbs – high beam, Halogen The low beam bulb is concealed by the larger cover. The high beam bulb is concealed behind the larger cover. 1. Remove the headlight housing from the vehicle (see Bulbs – headlight housing (p. 337)). 1. Remove the headlight housing from the vehicle (see Bulbs – headlight housing (p. 337)). 2. Remove the cover over the bulbs (see Bulbs – cover (p. 338)). 2. Remove the cover over the bulbs (see Bulbs – cover (p. 338)).
MAINTENANCE AND SERVICING Bulbs – extra high beam The extra high beam bulb is concealed by the larger cover. Extra high beam2 1. Remove the headlight housing from the vehicle (see Bulbs – headlight housing (p. 337)). 2. Remove the cover over the bulbs (see Bulbs – cover (p. 338)). 3. Remove the bulb by turning it counterclockwise and pulling it straight out. 4. Remove the connector from the bulb. 5. Press the new bulb into the socket and turn it clockwise to put it in place.
MAINTENANCE AND SERVICING Related information • Bulbs – specifications (p. 343) Bulbs – location of taillight bulbs Backup lights The following illustrations show the location of the bulbs in the taillight cluster. 1. Open the panel in the trunk. 2. Remove the bulb holder by turning it counterclockwise. 3. Remove the defective bulb by pressing it in slightly and turning it counterclockwise before pulling it out. 4. Insert a new bulb, press it in and turn it clockwise. 5.
MAINTENANCE AND SERVICING Bulbs – taillight housing The bulbs in the taillight cluster are replaced from inside the trunk (not the LED functions). 5. Related information • • • NOTE Before starting to replace a bulb, see Bulbs – introduction (p. 336). 342 Press the bulb holder back into place and reinstall the cover. Bulbs – license plate lighting The license plate lighting is located next to the trunk handle. Bulbs – introduction (p. 336) Bulbs – location of taillight bulbs (p.
MAINTENANCE AND SERVICING Bulbs – trunk lighting Bulbs – vanity mirror lighting Bulbs – specifications The trunk lighting is located on opposite sides of the trunk. The vanity mirror bulbs are located behind the lens. The following bulbs can be replaced by the vehicles owner. All other bulbs should only be replaced by a trained and qualified Volvo service technician. G021758 Removing the lens 1. Insert a screwdriver and gently turn so that the bulb housing comes loose. 2. Replace the bulb. 3.
MAINTENANCE AND SERVICING || Lighting function Wattage Bulb Backup light 21 H21W LL Brake light 21 P21W LL Trunk lighting 10 SV8.5 (length 38mm) Front footwell lighting 3 W2, 1x9.5d type T10 Wiper blades – service position The windshield wiper blades must be in the vertical (service) position for replacement, washing or to lift them away from the windshield when e.g., removing ice or snow. To put the windshiield wipers in the service position: 1.
MAINTENANCE AND SERVICING Wiper blades – windshield With the wipers in the service position, fold out the wiper arm from the windshield. Press the button on the wiper blade attachment and pull the wiper blade straight out, parallel with the wiper arm. The wiper blades should be replaced regularly for best effect. The windshield wiper blades must be in the vertical (service) position for replacement, washing or to lift them away from the windshield when e.g., removing ice or snow.
MAINTENANCE AND SERVICING Engine compartment – washer fluid Washer fluid helps keep the windshield and headlights clean. During cold weather, the reservoir should be filled with windshield washer solvent containing antifreeze. Use Volvo Original Washer Fluid or the equivalent with a recommended pH value between 6 and 8. • • 6.8 US qts (6.5 liters) 4.7 US qts (4.5 liters4) Related information • Wiper blades – service position (p.
MAINTENANCE AND SERVICING Contains corrosive acid. Battery – handling The battery's service life is affected by the number of starts, if it has been discharged, driving style, driving conditions, weather conditions ,etc. Handling Risk of explosion Recycle properly NOTE A used battery should be disposed of in an environmentally responsible manner. Consult your Volvo retailer or take the battery to a recycling station. Related information • • • Battery – changing (p. 349) Battery – handling (p.
MAINTENANCE AND SERVICING || 348 Related information • • • Battery – changing (p. 349) Battery – maintenance Battery – maintenance (p. 348) Proper battery maintenance can help prolong its service life. Battery – symbols (p. 346) Maintenance • The service life of a battery is affected by factors such as driving conditions and climate. Extreme cold may also further decrease the battery’s starting capacity.
MAINTENANCE AND SERVICING Battery – changing When changing batteries, be sure to use the correct battery for your vehicle. Consult a Volvo retailer or a trained and qualified Volvo service technician. WARNING Connect and disconnect the positive and negative cables in the correct sequence.
MAINTENANCE AND SERVICING || Removal Switch off the ignition, remove the remote key from the ignition slot and wait at least 5 minutes before disconnecting the battery so that all information in the vehicle's electrical system can be stored in the control modules. Rally bar R-Design models* • After a new battery has been installed (see the following section), reinstall the rally bar in the reverse order. NOTE When reinstalling the rally bar, tighten the screws to 22 ft lbs (30 Nm).
MAINTENANCE AND SERVICING Installation 1. Lower the battery into the battery box. Fuses – introduction Location of the fuseboxes The fuses help protect the vehicle's electrical components from overloading. There are relay/fuseboxes located in the engine compartment, the passenger compartment and the trunk. If an electrical component fails to function, this may be due to a blown fuse. The easiest way to see if a fuse is blown is to remove it. To do so: 2.
MAINTENANCE AND SERVICING Fuses – engine compartment The fuses in the engine compartment protect e.g., engine and brake functions.
MAINTENANCE AND SERVICING Engine compartment, upper Pos Engine compartment, front Engine compartment, lower Positions These fuses are all located in the engine compartment box. Fuses in C are located under A. A decal on the inside of the cover shows the positions of the fuses. • • Fuses 1 – 15, 34 and 42 – 44 are relays/ circuit breakers and should only be removed or replaced by a trained and qualified Volvo service technician. Fuses 16 – 33 and 35 – 41 may be changed at any time when necessary.
MAINTENANCE AND SERVICING || Pos Function A Control module - automatic transmission 15 A/C compressor (not 4cyl. engines) 15 Relay-coils A/C, relay coils in engine compartment cold zone for Start/Stop 5 Starter motor relayA 30 Engine control module (4cyl. engines) 20 Ignition coils (5 cyl. engines) 354 Pos Function A A/C compressor (5-cyl. engines), engine valves, oil level sensor (5-cyl. only) 10 Engine valves/oil pump/ center heated oxygen sensor (4-cyl.
MAINTENANCE AND SERVICING Fuses – glove compartment The fuses under the glove compartment protect components such as the infotainment system and optional power seat. Fusebox A: General fuses Fusebox B: Control module fuses Fold aside the upholstery covering the fuseboxes. Positions: fusebox A Pos Pos Function A 40 25 1. Press the cover's lock and fold it up. Circuit breaker for the infotainment system and for fuses 16-20 2. The fuses are accessible.
MAINTENANCE AND SERVICING || Pos Function A Controls in left rear passenger's door 20 Keyless drive* 7.5 Power driver's seat* 20 Power front passenger's seat* 20 Pos A - Pos Function A 7.5 Heated front passenger's seat* 15 Courtesy lighting, rain sensor*, HomeLInk® Wireless Control System* Heated driver's seat* 15 Steering wheel module 7.
MAINTENANCE AND SERVICING Pos Function Accelerator pedal sensor, autodim mirror function, heated rear seats* A 7.5 Brake lights 5 Power moonroof* 20 Immobilizer 5 Related information • • • Fuses – engine compartment (p. 352) Fuses – cargo area/trunk (p. 358) Fuses – engine compartment cold zone (Start/Stop only) (p. 359) * Option/accessory, for more information, see Introduction.
MAINTENANCE AND SERVICING Fuses – cargo area/trunk The fuses in the cargo area/trunk protect components such as trailer connections, the parking brake, etc.
MAINTENANCE AND SERVICING Fuses – engine compartment cold zone (Start/Stop only)7 There are fuses in the engine compartment cold zone on models with the Start/Stop function. Location of Start/Stop fuses Positions • • 7 Fuses A1, A2 and 1–11 are relays/circuit breakers and should only be removed or replaced by a trained and qualified Volvo service technician. Fuse 12 may be changed at any time when necessary. Option on 4-cyl.
MAINTENANCE AND SERVICING || Pos Function Circuit breaker: fusebox A under the glove compartment (see Fuses – glove compartment (p. 355)) 60 Circuit breaker: fusebox A under the glove compartment (see Fuses – glove compartment (p.
MAINTENANCE AND SERVICING Washing the car The vehicle should be washed at regular intervals since dirt, dust, insects and tar spots adhere to the paint and may cause damage. To help prevent corrosion, it is particularly important to wash the car frequently in the wintertime. The following points should be kept in mind when washing and cleaning the car: CAUTION Avoid using car washing detergents with a pH value lower than 3.5 or higher than 11.5.
MAINTENANCE AND SERVICING || CAUTION Automatic car wash • Avoid waxing or polishing plastic or rubber components • Polishing chromed strips can wear away or damage the surface The vehicle should be washed at regular intervals since dirt, dust, insects and tar spots adhere to the paint and may cause damage. To help prevent corrosion, it is particularly important to wash the car frequently in the wintertime.
MAINTENANCE AND SERVICING Polishing and waxing CAUTION Normally, polishing is not required during the first year after delivery, however, waxing may be beneficial. • Before applying polish or wax the vehicle must be washed and dried. Tar spots can be removed with kerosene or tar remover. Difficult spots may require a fine rubbing compound. • • After polishing use liquid or paste wax. • Waxing alone does not substitute for polishing a dull surface.
MAINTENANCE AND SERVICING || Leather care Volvo's leather upholstery is manufactured with a protectant to repel soiling. Over time, sunlight, grease and dirt can break down the protection. Staining, cracking, scuffing, and fading can result. Volvo offers an easy-to-use, non-greasy leather care kit formulated to clean and beautify your vehicle's leather, and to renew the protective qualities of its finish. The cleaner removes dirt and oil buildup.
MAINTENANCE AND SERVICING Cleaning the seat belts Clean only with lukewarm water and a mild soap solution. Cleaning floor mats The floor mats should be vacuumed or brushed clean regularly, especially during winter when they should be taken out for drying. Spots on textile mats can be removed with a mild detergent. For best protection in winter, Volvo recommends the use of Volvo rubber floor mats. Consult your Volvo retailer.
MAINTENANCE AND SERVICING || 5. NOTE When touching up the vehicle, it should be clean and dry. The surface temperature should be above 60 °F (15 °C). Related information • Repairing stone chips Sample color code: Canadian models G021832 Make sure you have the right color. See Label information (p. 368) for the location of this label (label number 4 in the illustration). Minor stone chips and scratches Material: • • • • Primer – can Place a strip of masking tape over the damaged surface.
SPECIFICATIONS
SPECIFICATIONS Label information The labels in your vehicle provide information such as the chassis number, paint code, tire inflation pressure, etc.
SPECIFICATIONS Location of labels }} 369
SPECIFICATIONS || List of labels Vehicle Emission Control Information. Your Volvo is designed to meet all applicable emission standards, as evidenced by the certification label on the underside of the hood. For further information regarding these regulations, please consult your Volvo retailer. Engine oil. This label contains the recommended engine oil specifications. Vehicle Identification Number (VIN). The VIN plate is located on the top left surface of the dashboard.
SPECIFICATIONS Dimensions This section lists your vehicle's most important dimensions. Dimensions–S60 Position Dimension in. (mm) A Ground clearance (curb weight + 2 B Wheelbase 109.3 (2776) C Length 182.5 (4635) D Load length, floor, seatback down E Load length, floor F Height people)A 4.9 (124 ) 68.9 (1749) 38.0 (965) 58.
SPECIFICATIONS || Position Dimension in. (mm) G Load height 19.4 (492) H Track, front 62.5 (1588)B/ 62.1 (1578)C I Track, rear 62.4 (1585)B/ 62.0 (1575)C J Load width, floor K Width 36.2 (919) 72.7 (1847) 73.5 (1866)D A B C D 372 L Width incl. door mirrors (folded out) 82.6 (2097) M Width incl. door mirrors (folded in) 74.8 (1899) Varies slightly depending on tire size, optional sport chassis, etc.
SPECIFICATIONS Weights The following table lists important weight data for your vehicle. Category USA Canada 4-cyl. FWDA 4720 lbs 2140 kg AWDB 4870 lbs 2210 kg 4-cyl. FWD 1025 lbs 465 kg 4-cyl. AWD 1025 lbs 465 kg 4-cyl. FWD 2560 lbs 1160 kg 4-cyl. AWD 2630 lbs 1195 kg 4-cyl. FWD 2270 lbs 1030 kg 4-cyl. AWD 2370 lbs 1075 kg Curb weight 3510 - 3830 lbs 1580 - 1740 kg Max. roof load 165 lbs 75 kg Gross vehicle weight 4-cyl.
SPECIFICATIONS || Category USA Canada Without brakes 1650 lbs 750 kg With brakes, 1 7/8” ball 2,000 lbs 900 kg With brakes, 2” ball 3,300 lbs 1500 kg Max. tongue weight 165 lbs 75 kg Max. trailer weights A B Front Wheel Drive All Wheel Drive Related information • • 374 Loading specifications (p. 304) Loading specifications – load limit (p.
SPECIFICATIONS Engine specifications The following table provides technical data for the respective engines. Engine specifications for Special Edition vehicles may vary. Some of the engines listed here may not be available in all markets.
SPECIFICATIONS Oil specifications Oil viscosity Full synthetic engine oil meeting the minimum ACEA A5/B5 must be used. Lower quality oils may not offer the same fuel economy, engine performance, or engine protection. Incorrect viscosity oil can shorten engine life under normal use. SAE 5W-30 will provide good fuel economy and engine protection. See the viscosity chart.
SPECIFICATIONS Oil volume The following table provides technical data for the respective engines. Some of these engines may not be available in all markets. Engine specifications for Special Edition vehicles may vary. Engine model Approx. volume (incl. filter) 6-cylinder 7.18 US qts (6.8 liters) 5-cylinder 5.8 US qts (5.5 liters) 4-cylinder 6.2 US qts (5.9 liters) Related information • • Engine compartment – engine oil (p. 331) Oil specifications (p.
SPECIFICATIONS Coolant – specification and volume The table lists coolant volumes and specifications. System Volume Specification B4204T9 8.7 US qts. (8.3 liters) Coolant with corrosion inhibitor mixed with water (50/50 mix), see packaging. B4204T12 B4204T11 B4204T43 Transmission oil – specification and volumes Brake fluid – specification and volume The table lists transmission oil1 volumes and specifications.
SPECIFICATIONS Power steering – specification This fluid is used to help reduce and regulate steering force. Specification:Power steering fluid recommended by Volvo. Related information • Engine compartment – power steering fluid (p. 335) Fuel tank volume – specification and volume The table lists the fuel tank volume for your vehicle. Volume Specification 17.8 US gallons (67.5 liters) – Related information • Refueling – opening/closing fuel filler door (p.
SPECIFICATIONS Tire inflation – pressure table The following tire pressures are recommended by Volvo for your vehicle. Refer to the tire infla- Tire size tion placard (see Tire inflation – general information (p. 300) for its location) for information spe- cific to the tires installed on your vehicle at the factory. Some of the tire sizes listed here may not be available for all models in all markets.
SPECIFICATIONS Air conditioning – specification and volume The air conditioning system in your vehicle contains the following: Refrigerant: R134a (HFC134a) Volume: 1.
SPECIFICATIONS Battery specifications If the battery is replaced, replace it with a battery of the same cold start capacity as the original (see the decal on the battery). 12 volt system with a voltage-regulated alternator. Single pole system in which the chassis and engine block are used as conductors. The negative terminal is connected to the chassis.
SPECIFICATIONS Symbols – general information with necessary information about one of the vehicle's systems. The following tables list the most common warning and indicator lights and symbols and a reference to where more detailed information can be found. Related information • Information displays – indicator symbols (p. 67) Introduction • Information displays – warning symbols (p. 69) • Information display – messages (p.
SPECIFICATIONS || Symbols in the main instrument panel Indicator symbols Warning symbols in the instrument panel The following tables list the most common warning and indicator lights and symbols and a reference to where more detailed information can be found. Symbol A Description See Low oil pressure (p. 69) Parking brakeA (p. 69) SRS airbags (p. 69) Seat belt reminder (p. 69) Generator not charging (p. 69) Fault in the brake system (p. 69) Warning symbol (p.
SPECIFICATIONS Information symbols Symbol The following tables list the most common warning and indicator lights and symbols and a reference to where more detailed information can be found. : The red warning symbol illuminates to indicate a problem related to safety and/or drivability. A message will also appear in the main instruments panel's display. : The information symbol illuminates and a text message is displayed to provide the driver with necessary information about one of the vehicle's systems.
SPECIFICATIONS Information symbols – ceiling console Information symbols – center console The following tables list the most common warning and indicator lights and symbols and a reference to where more detailed information can be found. The following tables list the most common warning and indicator lights and symbols and a reference to where more detailed information can be found. : The red warning symbol illuminates to indicate a problem related to safety and/or drivability.
INDEX INDEX Approach lighting A ABS (anti-lock brake system) 271 Accessory installation warning 22 Active chassis system 166 Active high beams 85 Active yaw control 166, 167 Adaptive brake lights 272 Adaptive cruise control 176 Airbags disconnecting the front passenger’s side front inflatable curtain side impact Air conditioning Air distribution Air distribution table Air vents Alarm All Wheel Drive Ambient temperature sensor Anti-freeze Anti-lock brake system warning light Anti-lock Brake S
INDEX ISOFIX/LATCH anchors top tether anchors 54 55 Courtesy lighting 91 Crash event data 17 Child safety booster cushions child restraint systems convertible seats infant seats 45 53 47 51 48 Crash mode Curb weight 304 Eco (driving function) 267 Child safety locks 56 Current, conserving 278 Eco coast 267 206, 210 Eco guide City safety 195, 196 Climate system 128 air distribution 123, 129, 131 air vents 123 Interior Air Quality System 121 introduction 120 passenger compartment filter
INDEX starting switching off 252 253, 255 Front seats heated 75 126 H 283 Hazard warning flashers Engine compartment overview 330 Fuel filler cap Engine Drag Control (EDC) 167 Fuel filler door, opening Engine oil checking low pressure warning light volumes 376 331 69 377 Fuel level warning light Engine remote start (ERS) 254 Environment 282, 283 68 Fuel requirements 279, 280 Fuel tank volume Fuses 379 351, 352, 358 21 Headlights Active Bending Lights 86 active high beams 85 changing
INDEX Horn 82 I ID, Volvo Ignition modes Immobilizer Important information Indicator lights Jack attaching location of 295 295 Jump starting 255 146 13 63, 65, 69 48 Inflatable Curtain 40 Inflation pressure 300, 301 K Key blade 144, 145, 146, 148, 149, 150, 151, 154 private locking 150 valet locking 150 Information and warning symbols, table of 383 Keyless drive general description starting the vehicle Information lights Keyless locking/unlocking 380 63, 65, 69 Inspection readiness 327
INDEX Motor oil checking volumes P 331 377 R Paint, touching up 365 Park assist O Occupant safety 26 Occupant weight sensor 36 Octane recommendations Odometer, trip 280 73 Oil checking volumes 331 377 Oil level sensor 231, 239 240 Rear park assist Park Assist Pilot 235 Rear seats center head restraint folding heated Parking brake electric, applying/releasing warning light 273, 274, 276 69 Parking lights 88 Pedestrian detection 207, 210 Polishing 363 332 76 Oil quality 376 Pow
INDEX key blade 144, 145, 146, 148, 149, 150, 151 locking the vehicle 147 replacing the battery 152 unlocking the vehicle 147 Reporting safety defects 27 Roadside Assistance 23 use during pregnancy using Seats, front Sensus 13 261 171 Roof loads 139 Side door mirrors Side impact airbags 307 Safety defects, reporting 27 Spare tire Spin control SRS Seat belts Automatic locking retractor/Emergency locking retractor 47 buckling 29 maintenance 29 pretensioners 28 reminder 30 reminder warning light
INDEX Three-way catalytic converter 283 Towing a trailer 285, 287 Tire designations 302 Towing the vehicle 288, 289 Tire inflation pressure 380 Traction control 166, 167 Trailer towing 285, 287 Transmission general description Hill Start Assist oil shiftlock override 256, 259 257 378 261 Tire Monitor 309, 310, 311 Tire Pressure Monitoring System indicator light 312, 315 68 Tires age changing from summer to winter glossary of terms improving economy inflation pressure inflation pressure t
INDEX Warranties 324 Washer fluid 346 Washers headlight windshield 94 93 Water, driving through 277 Waxing 363 Weights 373 Wheels changing storing 292 295 293 Whiplash Protection System 41 Windows power sun shade 96 96 Windshield heated rain sensor washers wipers/washers Windshield washer fluid 346 Windshield wipers service position 344 344 Wiper blades replacing 394 99, 128 94 94 93 344, 345
TP 20970 (English - USA & Canada), AT 1617, MY17, Printed in Sweden, Göteborg 2016, Copyright © 2000-2016 Volvo Car Corporation
