Specifications

QUADRAPADDLE SIGNAL CONTACTS AND MODULES USER’S MANUAL: SECTION 6 VIRGINIA PANEL CORPORATION
2/22/10
6-1 For more information visit vpc.com
TOOLS REQUIRED
3
/
32
Allen Wrench
PCB ADAPTER INSTALLATION AND REMOVAL INSTRUCTIONS
1. Using the supplied
3
/
32
Allen wrench, install the receiver module into the
receiver frame with the two 4-40 x 1¼” screws. Note that the screws will
extend approximately 0.75” to 1.0” [19-25 mm] beyond the rear of the
receiver frame. Ensure that Position 1 is located at the top for systems
in which the modules are oriented vertically or to the left for systems in
which the modules are oriented horizontally (Figure A).
2. Access the rear of the receiver frame and install the 4-40 stand-offs to
the 4-40 X 1¼” module retaining screws according to Table 1 (Figure B).
3. Align the PCB adapter’s two threaded retaining sockets with the 4-40
x 1¼” module retaining screws with stand-offs installed (Figure C).
Ensure that Position 1 on the adapter corresponds with Position 1 on the
module.
4. Using the
3
/
32
Allen wrench, carefully install the PCB adapter by
tightening the retaining sockets, turning each no more than 1½
to 2 full revolutions before alternating to the other socket. Repeat
this step until the PCB adapter is rmly engaged with the receiver
module, taking care not to over-tighten, maximum torque of 4
in-lbs [0.45 Nm].
5. To remove the PCB adapter from the receiver frame and
module, use the same alternating method of 1½ to 2 turns until
the PCB adapter is fully disengaged.
QUADRAPADDLE SIGNAL RECEIVER PCB ADAPTER INSTALLATION AND REMOVAL
PART # 510 150 125 / 510 150 126 / 510 150 127 / 510 150 128 /
510 150 141 / 510 150 142 / 510 150 148 / 510 150 155
TCERROC STNESERPER WEIV SIHT
NEHW NOITATNEIRO ELUDOM
CPV A NI DECALP YLREPORP
ROTACIDNI A1 POSTION ETON - REVIECER
NOITISOP TFEL REPPU TA DETACOL
ROTACIDNI A1 POSITION
)DEDLOM
(
EMARF REVIECER CPV
DEILPPUS TON
1 ELBAT .FER
[ ]
Figure A. Install receiver module onto
receiver frame.
EMARF REVIECER CPV
DEILPPUS TON
1 ELBAT .FER
[ ]
1
2
Figure B. Install proper stand-off.
[ ]
EMARF REVIECER CPV
DEILPPUS TON
1 ELBAT .FER
[ ]
[ ]
Figure C. Install PCB adapter.
RECEIVER FRAME
STYLE
RECEIVER FRAME
THICKNESS
STAND-OFF
CONFIGURATION
ITEMS
TO BE USED
9025, 9025TR, 9050,
9075, SL4, S6, G12, and
G12x
0.545
[13.84]
⅛" [3.18 mm] stand-off
per mounting screw
Item 
Small 90 Series (3,6,10),
G2, G6, G10, and G18
(NON-PCB)
0.365
[9.27]
5
/
16
" [7.94 mm] stand-off
per mounting screw
Item 
G10 (PCB) and G18
(PCB)
0.250
[6.35]
Both ⅛" [3.18 mm] and
5
/
16
" [7.94 mm] stand-off
per mounting screw
Item 
Table 1.
Dimensions shown: [millimeters]
inches