Operator’s Manual Vibroplate VP 1340A VP 1340AW VP 1550A VP 1550AW 5000191741 04 0811
Copyright notice © Copyright 2011 by Wacker Neuson Corporation. All rights, including copying and distribution rights, are reserved. This publication may be photocopied by the original purchaser of the machine. Any other type of reproduction is prohibited without express written permission from Wacker Neuson Corporation. Any type of reproduction or distribution not authorized by Wacker Neuson Corporation represents an infringement of valid copyrights. Violators will be prosecuted.
VP 1340R/VP1550R Table of Contents Foreword 3 1 Emission Control system Information 4 2 Safety Information 5 3 4 2.1 Laws Pertaining to Spark Arresters ...................................................... 5 2.2 Operating Safety .................................................................................. 6 2.3 Operator Safety while using Internal Combustion Engines .................. 7 2.4 Service Safety ..............................................................................
Table of Contents 5 VP 1340R/VP1550R Maintenance 5.1 5.2 5.3 5.4 5.5 5.6 5.7 5.8 5.9 5.10 5.11 5.12 5.13 5.14 5.15 20 Maintaining the Emission Control System............................................20 Periodic Maintenance Schedule ..........................................................20 Spark Plug ...........................................................................................22 Air Cleaner ..........................................................................................
WARNING CALIFORNIA Proposition 65 Warning: Engine exhaust, some of its constituents, and certain vehicle components, contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Foreword This manual provides information and procedures to safely operate and maintain this Wacker Neuson model. For your own safety and protection from injury, carefully read, understand and observe the safety instructions described in this manual.
Emission Control System Information 7 Emission Control Systems Information and Warranty The Emission Control Warranty and associated information is valid only for the U.S.A., its territories, and Canada. 7.1 Emission Control Systems Warranty Statement See the supplied engine owner’s manual for the applicable exhaust and evaporative emission warranty statement. wpm_tx001755gb.
VP 1340A/VP 1550A 2. Safety Information Safety Information This manual contains DANGER, WARNING, CAUTION, NOTICE, and NOTE signal words which must be followed to reduce the possibility of personal injury, damage to the equipment, or improper service. This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Safety Information 2.2 VP 1340A/VP 1550A Operating Safety WARNING Familiarity and proper training are required for the safe operation of the machine. Machines operated improperly or by untrained personnel can be hazardous. Read the operating instructions contained in this manual and the engine manual, and familiarize yourself with the location and proper use of all controls. Inexperienced operators should receive instruction from someone familiar with the machine before being allowed to operate it. 2.
VP 1340A/VP 1550A 2.3 Safety Information Operator Safety while using Internal Combustion Engines WARNING Internal combustion engines present special hazards during operation and fueling. Read and follow the warning instructions in the engine owner’s manual and the safety guidelines below. Failure to follow the warnings and safety standards could result in severe injury or death. 2.3.
Safety Information 2.4 VP 1340A/VP 1550A Service Safety A poorly maintained machine can become a safety hazard! In order for the machine to operate safely and properly over a long period of time, periodic maintenance and occasional repairs are necessary. WARNING 2.4.1 Do not attempt to clean or service the machine while it is running. Rotating parts can cause severe injury. 2.4.2 Do not crank a flooded engine with the spark plug removed on gasoline-powered engines.
VP 1340A/VP 1550A 2.5 Safety Information Label Locations wpmgr005939 wpm_si000423gb.
Safety Information 2.6 VP 1340A/VP 1550A Warning and Informational Labels Wacker Neuson machines use international pictorial labels where needed. These labels are described below. Label Meaning WARNING! Always wear hearing and eye protection when operating this machine. WARNING! Hot surface Guaranteed sound power level in dB(A). WARNING! Hand injury if caught in moving belt. Always replace beltguard. CAUTION! Read and understand the supplied Operator’s Manual before operating this machine.
VP 1340A/VP 1550A Label Safety Information Meaning Throttle control lever: Turtle = Idle or Slow Rabbit = Full or Fast DANGER! Engines emit carbon monoxide; operate only in well-ventilated area. Read the Operator’s Manual. No sparks, flames, or burning objects near the machine. Shut off the engine before refueling. Label-machine model Company logo Company label A nameplate listing the model number, item number, revision number, and serial number is attached to each unit.
Safety Information Label VP 1340A/VP 1550A Meaning This machine may be covered by one or more patents. wpm_si000423gb.
Technical Data 3. VP 1340A/VP 1550A Technical Data 3.1 Engine Data Engine Power Rating Net power rating per SAE J1349. Actual power output may vary due to conditions of specific use. VP 1340A/AW 0009031 0009032 VP 1550A/AW 0009027 0009028 Engine Engine Make Honda Engine Model GX 160 UT1 SWX2 Maximum rated power @ rated speed kW (Hp) Spark Plug Electrode Gap 3.6 (4.8) @ 3600 rpm NGK BPR 6ES mm (in.) 0.7-0.8 (0.028–0.
VP 1340A/VP 1550A 3.2 Technical Data Machine Data VP 1340A/AW 0009031 0009032 VP 1550A/AW 0009027 0009028 Plate Weight kg (lbs.) Water Tank Capacity Exciter Speed VP 1550A: 83 (184) VP 1550AW: 86 (190) 3.8 (4.0) 7.6 (8.0) rpm Exciter Lubrication Dimensions 3.3 l (qts.) VP 1340A: 74 (163) VP 1340AW: 76 (168) 5800 ± 100 ml (oz.) 240 (8) Automatic transmission fluid Dextron III/Mercon or equivalent mm (in.
Technical Data 3.4 VP 1340A/VP 1550A Dimensions mm (in.) 911 (36) 400 (16) 588 (23) wpmgr005966 wpm_td000314gb.
VP 1340A/VP 1550A 4. Operation Operation 4.1 Recommended Fuel The engine requires regular grade unleaded gasoline. Use only fresh, clean gasoline. Gasoline containing water or dirt will damage fuel system. Consult engine owner’s manual for complete fuel specifications. Use of oxygenated fuels Some conventional gasolines are blended with alcohol. These gasolines are collectively referred to as oxygenated fuels.
Operation 4.3 VP 1340A/VP 1550A Before Starting 4.3.1 Read and understand the safety and operating instructions at the beginning of this manual. 4.3.2 Check: wpm_tx001087gb.
VP 1340A/VP 1550A 4.4 Operation To Start See Graphic: wc_gr000014 4.4.1 Open fuel valve by moving lever to the right (a1). Note: If engine is cold, move choke lever to close position (b1). If engine is hot, set choke to open position (b2). 4.4.2 Turn engine switch to “ON” (e1). 4.4.3 Open throttle by moving it slightly to left (d1). 4.4.4 Pull starter rope (c). Note: If the oil level in the engine is low, the engine will not start. If this happens, add oil to engine.
Operation 4.6 VP 1340A/VP 1550A Operation Run the engine at full throttle and allow the plate to pull itself along at its normal speed. When operating on an incline it may be necessary to assist the plate by pushing it forward slightly. When operating downhill hold the plate back slightly, if it begins to pick up speed. Depending on the material being compacted, three or four passes are recommended to achieve the best compaction.
VP 1340A/VP 1550A 5. Maintenance Maintenance 5.1 Maintaining the Emission Control System Normal maintenance, replacement or repair of emission control devices and systems may be performed by any repair establishment or individual; however, warranty repairs must be performed by a dealer/service center authorized by WACKER NEUSON.
Maintenance VP 1340A/VP 1550A Machine Maintenance The chart below lists basic machine maintenance. Daily before starting Check external hardware. After first 20 hrs. Every 2 weeks or 50 hrs. Every month or 100 hrs. Every year or 300 hrs. Check and adjust drive belt. Inspect shockmounts for damage. Replace shockmounts as needed. Change exciter oil.
VP 1340A/VP 1550A 5.3 Maintenance Spark Plug See Graphic: wc_gr000028 Clean or replace the spark plug as needed to ensure proper operation. Refer to your engine operator’s manual. The muffler becomes very hot during operation and remains hot for a while after stopping the engine. Do not touch the muffler while it is hot. WARNING Note: Refer to section “Technical Data” for the recommended spark plug type and the electrode gap setting. 5.3.1 Remove the spark plug and inspect it. 5.3.
Maintenance 5.4 VP 1340A/VP 1550A Air Cleaner See Graphic: wc_gr000025 The engine is equipped with a dual element air cleaner. Service air cleaner frequently to prevent carburetor malfunction. NOTICE: NEVER run engine without air cleaner. Severe engine damage will occur. NEVER use gasoline or other types of low flash point solvents for cleaning the air cleaner. A fire or explosion could result. WARNING To service: 5.4.1 Remove air cleaner cover (a).
VP 1340A/VP 1550A 5.5 Maintenance Engine Oil See Graphic: wc_gr000022 5.5.1 Drain the oil while the engine is still warm. 5.5.2 Remove the oil filler plug (a) and the drain plug (b) to drain the oil. Note: In the interests of environmental protection, place a plastic sheet and a container under the machine to collect any liquid that drains off. Dispose of this liquid in accordance with environmental protection legislation. 5.5.3 Install the drain plug. 5.5.
Maintenance 5.7 VP 1340A/VP 1550A Carburetor Adjustment See Graphic: wc_gr000032 5.7.1 Start the engine and allow it to warm up to operating temperature. 5.7.2 Set the pilot screw (a) two turns out. See Note. 5.7.3 With the engine idling, turn the pilot screw (a) in or out to the setting that produces the highest rpm. 5.7.4 After the pilot screw is adjusted, turn the throttle stop screw (b) to obtain the standard idle speed. See Technical Data.
VP 1340A/VP 1550A 5.9 Maintenance Drive Belt See Graphic: wpmgr005992 On new machines or after installing a new belt, check the belt tension after first 20 hours of operation. Check and adjust the belt every 50 hours thereafter. To adjust the belt: 5.9.1 Loosen the two screws (a) on the beltguard, then remove the beltguard, keeping the screw assemblies captured on the beltguard. 5.9.
Maintenance VP 1340A/VP 1550A 5.10 Exciter Lubrication See Graphic: wpmgr006018 The bearings in the exciter assembly are splash lubricated and rotate at very high speed. It is important to maintain the exciter oil at the correct level and change it regularly. Check oil level in exciter every 50 hours of operation. To check oil level, place plate on a flat, level surface. Remove the drain plug (a) with seal ring (b). Oil level should be at drain plug threads. Add oil as required.
VP 1340A/VP 1550A Maintenance 5.12 Lifting Machine See Graphic: wpmgr006022 See Technical Data for weight of the machine. To lift machine manually: 5.12.1 Stop the engine. 5.12.2 Obtain help from a partner and plan the lift. WARNING To avoid burns or fire hazards, let the engine cool before transporting the machine or storing it indoors. Turn the fuel valve to the off position and keep the engine level to prevent fuel from spilling. 5.12.3 Grasp machine by the lifting handles (a) and (b).
Maintenance VP 1340A/VP 1550A 5.13 Transporting Machine See Graphic: wpmgr006042 To avoid burns or fire hazards, let engine cool before transporting machine or storing indoors. WARNING 5.13.1 Turn fuel valve to the off position and keep the engine level to prevent fuel from spilling. 5.13.2 Tie down machine on vehicle to prevent machine from sliding or tipping over. Tie machine to vehicle at points shown on graphic. wpmgr006042 5.14 Storage If plate is being stored for more than 30 days: 5.14.
VP 1340A/VP 1550A Maintenance 5.15 Troubleshooting Problem / Symptom Reason / Remedy Plate does not develop full speed. Poor compaction. • Engine throttle control not completely open. • Throttle control not adjusted correctly. • Ground too wet, plate sticking. Allow soil to dry before compacting. • Drive belt loose or worn, slipping on pulleys. Adjust or replace belt. Check that engine mounting bolts are tight. • Exciter bearings binding. Check condition and level of oil in exciter.
EC Declaration of Conformity Manufacturer Wacker Neuson Manila, Inc. Dasmariñas, Cavite, Philippines Product Product VP 1340A, VP 1340AW, VP 1550A, VP 1550AW Product category Vibrating plate Product function Compacting soils Item number 0630057, 0630058, 0630054, 0630055 Net installed power 3.6 kW Measured sound power level 105 dB(A) Guaranteed sound power level 108 dB(A) Conformity assessment procedure According to 2000/14/EC, Appendix VI, 2005/88/EC.
Wacker Neuson SE, Preußenstraße 41, D-80809 München, Tel.: +49-(0)89-3 54 02-0 Fax: +49 - (0)89-3 54 02-390 Wacker Neuson Production Americas LLC, N92W15000 Anthony Ave., Menomonee Falls, WI 53051 Tel. : (262) 255-0500 Fax: (262) 255-0550 Tel.: (800) 770-0957 Wacker Neuson Limited - Room 1701–03 & 1717–20, 17/F. Tower 1, Grand Century Place, 193 Prince Edward Road West, Mongkok, Kowloon, Hongkong.
