R0 Silencer BT 2.
Table of Contents About Your Earbuds Earbud Overview How to Properly Fit the Silencer BT 2.0 Device Function Connect to Walker’s LINK App Walker’s LINK APP Features FCC Compliance Limited Warranty Warranty Registration 3 4 5 6 7 8 12 13 14 Contact Us WEBSITE www.walkersgameear.com GSM, LLC P.O.
About Your Earbuds Touch Interface Control your ear buds with ease, using gesture-based touch controls. Bluetooth Enabled Connect your Silencer BT 2.0 earbuds to your phone to control with ease on our Walker’s LINK app, free on iOS and Android. Sleep Mode Conserve device battery with our automatic device shut off. Extended Battery Life Never cut a session short with over 10 hours of battery life in a single charge.
Earbud Overview LED Status Light Multi-Touch Interface Ambient Volume Up Touchable Area Cleaning Brush Micro USB Charging Port Page 4 Ambient Volume Down
How to Properly Fit the Silencer BT 2.0 Fitment Instructions Press the arrows in the top right of the Walker’s Link app, or swipe right, to access the Fitment Instruction page. On this page, you will find detailed instructions and diagrams to assist in properly fitting your earplugs. To return to main screen of app, press the arrows in the top left corner, or swipe left. When inserting ear buds grab by sides as to not activate ear buds with touch surface.
Device Function Power On Device: Press and hold touch surface for 2 seconds to power on each ear bud. Ear buds will play an audible “Walker’s” sound clip to indicate the unit has powered on. Ambient Volume Adjust: Ambient Volume is controlled by the touch sensor controls located on the housing of both ear buds. • • Increase Ambient Volume: Swipe Up Decrease Ambient Volume: Swipe Down NOTE: When Ambient volume reaches minimum there will be a double beep.
Connect to Walker’s LINK App Upon initial start up the Silencer BT 2.0 will enter pairing mode automatically and you will hear an audible “Pairing” clip when the Silencer BT 2.0 is ready to be connected to your device. The Silencer BT 2.0 will also flash Red and Blue when in Pairing mode. Power On Device: 1 Hold the power button on your Walker’s Silencer BT 2.0 for 2 seconds to power on the earbuds.
Walker’s LINK APP Features Download our free Walker’s LINK app available on the Apple App Store & Google Play. Volume Adjust: Use the dual sliders in the app to increase or decrease the ambient volume of your earbuds. Check Fitment: This setting will mute all ambient volume on the earbuds to allow you to more easily check the seal on your earplugs.
Bluetooth Settings (Left Earbud Only) Use the LEFT earbud to control device Bluetooth Settings. Pairing the device To enter pairing mode, from the powered down state, press and hold the touch zone for 5 seconds. An audible notification will play (“Pairing”) when the device enters pairing mode. Pairing Mode • In this mode, the unit will advertise itself and allow itself to be paired to a new device. • The device will enter this mode automatically when no previous paired device profile is present.
Walker’s LINK APP Features (cont.) Volume Adjust Slider Fitment Instructions Page Silencer BT 2.
NRR Information Although hearing protectors can be recommended for protection against the harmful effects of impulsive noise, the Noise Reduction Rating (NRR) is based on the attenuation of continuous noise and may not be an accurate indicator of the protection attainable against impulsive noise such as gunfire. The level of noise entering a person’s ear, when hearing protector is worn as directed, is closely approximated by the difference between the A-weighted environmental noise level and the NRR.
FCC Compliance GSM, LLC GWP-SLCR2-BT FCC ID: MV3-GWPSLCR2BT IC: 9029A-GWPSLCR2BT FCC Statement: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions. (1) this device may not cause harmful interference, and (2) this devmice must accept any interference received, including interference that may cause undesired operation.
Limited Warranty Walker’s warranties this product to the original purchaser to be free from defects in materials and workmanship, under normal use and conditions for a period of one year parts from the date of purchase. Under this warranty, this device will be replaced or repaired at our option. Copy of the original receipt or gift receipt, is required for any warranty service.
Warranty Registration Model: Date of Purchase: Purchased From: City: State: Zip: Primary Use: Your Name: Address: City: Email Address: State: Zip: Serial #: ©2018 Google LLC, used with permission. Google and the Google logo are registered trademarks of Google LLC. Apple and iPhone are trademarks of Apple Inc., registered in the U.S. and other countries.
