User guide

READ THESE INSTRUCTIONS CAREFULLY BEFORE PROCEEDING WITH
INSTALLATION. CALL WATER, INC. SERVICE DEPARTMENT IF YOU HAVE ANY
QUESTIONS REGARDING THE INSTALLATION OF THIS PRODUCT.
DO NOT PLUG IN TANK OR TURN ON THE THERMOSTAT CONTROL KNOB
UNTIL YOU ARE TOLD TO DO SO IN THESE INSTRUCTIONS.
2. A 1 1/4” hole in your sink is needed, (or 1 3/8” if installing optional reverse osmosis airgap module) If you need
to drill a hole in your sink we suggest you consult a qualied installer. Try to position the EvErHot faucet so that
your existing/new sink faucet does not interfere with the EvErHot faucet.
3. If you have a Vinyl Gasket and a Flat Metal Washer (Fig.1): Assemble escutcheon and vinyl gasket over the
threaded faucet shank and insert assembly into sink hole. See Fig.1 for tube placement in gasket holes. Vinyl
gasket must be used. DO NOT USE plumber’s putty.
If you have a C-Shaped Metal Washer (see Fig.1A to conrm that you have the C-Shaped Washer): Assemble
escutcheon that has a built-in gasket over the threaded faucet shank and insert assembly into sink hole. DO NOT
USE plumber’s putty.
4. From underneath the sink install the Flat Metal Washer OR the C-Shaped Metal Washer, spacer*, friction ring*,
lock washer, and nut onto the 5/16” clear/white Teon
®
tube and tighten nut on threaded shank.
*spacer & friction ring are only included with models LVH 500, 510, 610, and 1310
5. Loosen set screw at the rear of the faucet body using the allen wrench provided. (LVH 500, 510,
610 & 630 dual lever faucets only). Adjust spout to the desired position and tighten set screw. (DO NOT OVER-
TIGHTEN) Do not move or adjust the spout after tightening the set screw, as any movement of the spout after
installation could cause a leak or damage to the unit.
6. Position the heating tank assembly vertically beneath the faucet so that the 5/16” Teon
®
tube
from the spout reaches the center stainless steel tube on the tank and the tank touches the wall.
With a pencil, mark the wall at the top of the tank. Set the tank to one side. Mark a second line 2 1/4”
below the rst line. Install the bracket with bottom of the bracket even with the lower line. Hang tank on bracket.
DO NOT PLUG THE TANK ELECTRIC CORD IN YET!
7. Connect red tube that originates beneath the hot lever to the 1/4” integral push-to-connect tting at the top right
rear corner of the tank. See Fig.2 for tting tips, and see SCHEMATIC on PAGE 4 for undersink layout.
RED
BLUE
CLEAR/WHITE
(Note closely
spaced holes)
This is the vinyl
escutcheon gasket,
and this is how you place
the tubes through it
page 2
1.
*****************************************************************************************************************************
Please note that additional 1/4” tubing and other ttings may be needed for the installation and are not
provided with the product. Do not use pipe dope or Teon
®
tape on any tting for this installation.
Call the Water, Inc. Service Department at 1-800-322-9283 [Local 310-885-4400 ext. 112 or 115]
if you need assistance with this installation or service.
If service is required, rst disconnect the power cord and shut off water supply to the EvErHot. Then call Water, Inc.
Removal of the EvErHot without prior approval may void the warranty.
INSTALLATION INSTRUCTIONS
FOR MODELS LVH 500 / 510 / 610 / 630 / 720*/ 1000 / 1120*/ 1200*/ 1310
1-USERS’ GUIDE AND WARRANTY INFORMATION SHEET
1- EvErHot Faucet with bag containing: Escutcheon, Vinyl Gasket & Flat Metal Washer (Fig. 1) - or - C-Shaped Metal Washer (Fig. 1A),
Spacer, Lock Washer, Nut, and Mounting Nut Wrench.
1- EvErHot Tank Assembly
1- FITTING PACKAGE CONTAINING: 1- Mounting Bracket, 2- Screws for Mounting Bracket, 1- Allen Wrench,
and 1- 3/8” X 5/16” Quick Connect Reducing Union
* These faucets also use supplemental installation instructions along with this booklet.The red circled numbers (ex: ) relate to the supplemental instructions.
3
PARTS LIST
2
3
4
5
6
FIG. 1A
This is the C-Shaped Washer.
If you have the C-Shaped Washer,
then you also have a built-in
escutcheon gasket.
FIG. 1 if you have a Vinyl Gasket and Flat Metal Washer