Owner manual

Watlow EZ-ZONE
®
PM Integrated Controller • 111 • Chapter 7 Profiling Page
Display Step Type
Description
Parameters in Step Type
[UStP]
[UStP]
Step Types
Unused Step
This is an empty step that can be used to plan for future
steps to be inserted or temporarily deactivate a step in a
profile. Change step type back when the step should be ac-
tive again.
- - - -
[``ti]
[ ti]
Step Types
Time
If Ramping Type found in the Global Menu of the Setup
Page is set for Time, control loop 1 to 2 may be part of the
profile and all enabled control loops follow independent set
points over the specified time. The state of up to 2 event
outputs may be set or maintained.
[tg;S1] Target Set Point Loop 1
[tg;S2] Target Set Point Loop 2
[hoUr] Hours
[Min] Minutes
[`SEC] Seconds
[gSE1] Guaranteed Soak Enable 1
[gSE2] Guaranteed Soak Enable 2
[Ent1] Event 1
[Ent2] Event 2
[rAtE]
[rAtE]
Step Types
Rate
If Ramping Type found in the Global Menu of the Setup
Page is set for Rate, control loop 1 must be part of the profile
and if control loop 2 is enabled it must follow the same set
point and rate in degrees or units per minute. Ensure all
control loops have the same units of measure. The state of
up to 2 event outputs may be set or maintained.
[tg;S1] Target Set Point Loop 1
[tg;S2] Target Set Point Loop 2
[gSE1] Guaranteed Soak Enable 1
[gSE2] Guaranteed Soak Enable 2
[rAtE] Rate
[Ent1] Event 1
[Ent2] Event 2
[SoAH]
[SoAk]
Step Types
Soak
A Soak Step maintains the last Target Set Points for the
designated time. The state of up to 2 event outputs may be
set or maintained.
[hoUr] Hours
[Min] Minutes
[`SEC] Seconds
[gSE1] Guaranteed Soak Enable 1
[gSE2] Guaranteed Soak Enable 2
[Ent1] Event 1
[Ent2] Event 2
[CLoC]
[CLoC]
Step Types
Wait For Time
A Wait for Time Step is available with the real-time calen-
dar clock feature. This allows the program to wait for a spec-
ified day and time before proceeding to the next step. Used
to have the profile execute steps everyday or only weekdays.
The state of up to 2 event outputs may be set or maintained.
[hoUr] Hours
[Min] Minutes
[`SEC] Seconds
[dow] Day of Week
[Ent1] Event 1
[Ent2] Event 2
[`W;E]
[ W.E]
Step Types
Wait For Event
A Wait for Event Step will wait for the two Wait for Event
states (1 to 2) to match the specified state. The state of up
to 2 event outputs may be set or maintained.
[WE;1] Wait Event 1
[WE;2] Wait Event 2
[Ent1] Event 1
[Ent2] Event 2
[W;pr]
[W.Pr]
Step Types
Wait For Process
A Wait for Process Step will wait for Process Value 1 or 2 to
match the Wait for Process Value. The state of up to 2 event
outputs may be set or maintained.
[W;p1] Wait for Process 1
[W;p1] Wait for Process 2
[Ent1] Event 1
[Ent2] Event 2
[W;bo]
[W.bo]
Step Types
Wait For Both
A Wait For Process and Event Step will wait for Process
Value 1 or 2 to match the Wait for Process 1 value, and/or
the two Wait Event states to match the specified state. The
state of up to 2 event outputs may be set or maintained.
[W;p1] Wait for Process 1
[W;p1] Wait for Process 2
[WE;1] Wait Event 1
[WE;2] Wait Event 2
[Ent1] Event 1
[Ent2] Event 2
[``JL]
[ JL]
Step Types
Jump Loop
A Jump Loop step will repeat previous steps a number
of times designated in Jump Count. Jump Loops can be
nested up to four deep. The state of up to 2 event outputs
may be set or maintained.
[``JS] Jump Step
[``JC] Jump Count
[Ent1] Event 1
[Ent2] Event 2