Owner manual

Watlow EZ-ZONE
®
PM Integrated Controller • 114 • Chapter 8 Factory Page
Factory Page
Dis-
play
Parameter Name
Description
Range Default
Modbus
Relative Ad-
dress
CIP
Class
Instance
Attribute
hex (dec)
Pro-
fibus
Index
Param-
eter ID
Data
Type
&
Read/
Write
[Cust]
[fcty]
Custom
[`par]
[ Par]
Custom
Parameter 1 to 20
Select the parameters
that will appear in the
Home Page.
The Parameter 1 value
will appear in the
upper display of the
Home Page. It cannot
be changed with the Up
and Down Keys in the
Home Page.
The Parameter 2 value
will appear in the lower
display in the Home
Page. It can be changed
with the Up and Down
Keys, if the parameter
is a writable one.
Scroll through the other
Home Page parameters
with the Advance Key
‰
.
Note:
Display Pairs affect
the pairing of custom
parameters on the
Home page. For more
information on Display
Pairs see the section
in this guide entitled
"Modifying the Display
Pairs".
[nonE] None
[`L;hy] Limit Hysteresis
[`Lh;S] Limit High Set Point
[`LL;S] Limit Low Set Point
[`CU;r] Current Read
[`Pro] Process
[`i;CA] Calibration Offset
[`C_F] Display Units
[USr;r] User Settings Restore
[`A;Lo] Alarm Low Set Point
[`A;hi] Alarm High Set Point
[`A;hy] Alarm Hysteresis
[CUSt] Custom Menu
[StPt] Set Point
[AC;pu] Active Process Value
[AC;SP] Active Set Point
[``op] Open Loop Set Point
[`AUt] Autotune
[`C;M] Control Mode
[`h;Pr] Heat Power
[`C;Pr] Cool Power
[``ti] Time Integral
[``td] Time Derivative
[``db] Dead Band
[`h;Pb] Heat Proportional
Band
[`h;hy] Heat Hysteresis
[`C;Pb] Cool Proportional
Band
[`C;hy] Cool Hysteresis
[`r;rt] Ramp Rate
[t;tUn] TRU-TUNE+
®
Enable
[idLE] Idle Set Point
[P;Str] Profile Start
[P;ACr] Profile Action Request
[gSd1] Guaranteed Soak De-
viation 1
[gSd2] Guaranteed Soak De-
viation 2
See:
Home
Page
- - - - - - - - - - - - 14005 uint
RWES
[`iid]
[ iid]
Custom (1 to 20)
Instance ID
Select which instance of
the parameter will be
selected.
1 to 4
- - - - - - - - - - - - 14003 uint
RWES
[`LoC]
[FCty]
Lock Menu
[LoC;o]
[LoC.o]
Security Setting
Operations Page
Change the security
level of the Operations
Page.
1 to 3 2
Instance 1
Map 1 Map 2
1832 2302
0x67 (103)
1
2
- - - - 3002
uint
RWE
[LoC;P]
[LoC.P]
Security Setting
Profiling Page
Change the security lev-
el of the Profiling Page.
1 to 3 3
Instance 1
Map 1 Map 2
1844 2314
0x67 (103)
1
8
- - - - 3008
uint
RWE
[pas;e]
[LoC.P]
Security Setting
Password Enable
Set to On to require
a password for menu
changes.
[`off] Off
[``on] On
Off
- - - - - - - - - - - - 3009
uint
RWE
Note:
Some values will be rounded off to fit in the four-character display. Full values can be read
with other interfaces.
If there is only one instance of a menu, no submenus will appear.
R: Read
W: Write
E: EEPROM
S: User
Set