Owner manual
Watlow EZ-ZONE
®
PM Integrated Controller • 174 • Chapter11Appendix
B
Barometric Pressure 67
Baud Rate 98
Blocking 90, 137
bumpless transfer 131
C
Calibration Menu 118
Calibration Offset 54, 71, 88,
125–126
Cascade Control 135
changing the set point 45
Channel 97
chattering output 132
chemical compatibility 21
CIP - Communications Capabilities
142
CIP Implicit Assemblies 143
CIP Implicit Assembly Structures
160
CIP Implicit O to T (Originator to Tar-
get) Assembly Structure 160
CIP Implicit T to O (Target to Origi-
nator) Assembly Structure
160
Closed Loop Set Point 59, 84
Closed Loop Working Set Point 57
Common Industrial Protocol 50
CIP Implicit Assemblies 143
Compact Implicit Assembly Class
143, 161
Introduction to CIP 50
Modifying Implicit Assembly Mem-
bers 143
Common Industrial Protocol (CIP)
50
communications activity light 42
Communications Menu 98, 102, 107,
114
Setup Page 52, 67
Compact Assembly Class 143
Compact Class Assembly Structure
161
Compressor Control 151
Control 75, 86
Control Loop Menu 80
control methods 131
Control Mode 58, 85, 132
Control Mode Active 57
Control Module Menus
Factory Page
Calibration Menu 118
Security Setting Menu 114, 116
Operations Page
Alarm Menu 61
Analog Input Menu 54
Current Menu 62
Digital Input/Output Menu 56
Limit Menu 57
Linearization Menu 54
Loop Menu 58
Math Menu 63
Monitor Menu 57
Process Value Menu 55
Prole Status Menu 65
Special Output Function Menu 64
Setup Page
Alarm Menu 88
Analog Input Menu 69
Communications Menu 98, 102,
107, 114
Control Loop Menu 80
Current Menu 91
Digital Input/Output Menu 75
Global Menu 95
Limit Menu 79
Linearization Menu 71
Math Menu 92
Output Menu 85
Process Value 74
Cool Algorithm 80, 132
Cool Hysteresis 60, 81, 132
cool output curve 130
Cool Output Curve 80, 130
Cool Power 57, 123
Cool Proportional Band 59, 81, 123,
133
Current Error 63, 138
Current Menu 62, 91
current sensing 138
Current Sensing 138
D
Data Map 99
Date of Manufacture 116
Dead Band 60, 81, 133, 134
Decimal 70
default Home Page parameters 42,
45
deviation alarms 136
Differential Control 136
Digital Input Function 95
Digital Input/Output Menu 56, 75
dimensions 16, 17, 18, 19
Direction 75
Display 90
Display Pairs 68, 97
displays 42
Display Time 97
Display Units 95, 102
Down Key 42
duplex 128
E
Electrical Input Offset 118
Electrical Input Slope 118
Electrical Measurement 118
Electrical Output Offset 118
Electrical Output Slope 118
End 112
End Set Point Value 109
EtherNet/IP™ 35
Ethernet/IP™ Enable 101
Event Output (1 and 2) 110 , 111 , 112
Example: Using a Current Trans-
former 28
EZ Key 138
F
Factory Page 113
Filter Time 70, 126
lter time constant 126
Function 67, 124
Function Instance 75, 78
Function Key Menu 138
G
Global Menu 95
Setup Page 52, 67
Guaranteed Soak Devia-
tion 68
Guaranteed Soak Deviation 96
Guaranteed Soak Enable 68, 96
H
Heat Algorithm 80, 132
Heater Error 63, 138
Heat Hysteresis 59, 80, 132
Heat Power 57, 123
Heat Proportional Band 59, 80, 123,
133
High Power Scale 76, 86
high range 127
high scale 127
High Set Point
Alarm 61, 62, 90, 91, 136
Current 62, 63, 138
Loop 84, 127
Home Page 45
Hours 107
Hysteresis 79, 89, 137
I
Idle Set Point 59, 84
Input Error Failure 83, 131
Input Error Latching 70, 131
Input Error Status 54, 71
input events 6
Input Point 1 67
Input Point 2 67
Input Point 3 67
Input Point 4 67
Input Point 5 67
Input Point 6 67
Input Point 7 67
Input Point 8 67
Input Point 9 67
Input Point 10 67