User guide

Watlow EZ-ZONE
®
PM PID Controller • 118 • Appendix
[`o;Lo] Output Low Power Scale
53, 59
[``oP] Open Loop Set Point 40
[`oP;2] Output Point 2 50
[`oP;3] Output Point 3 50
[`oP;4] Output Point 4 50
[`oP;5] Output Point 5 50
[`oP;6] Output Point 6 50
[`oP;7] Output Point 7 50
[`oP;8] Output Point 8 50
[`oP;9] Output Point 9 51
[oP;10] Output Point 10 51
[`o;tb] Output Time Base 52, 59
[otPt] Output Menu 59
[`o;ty] Output Type 60, 92
[pas;a] Administrator Password 78,
81
[pas;e] Password Enable 78, 80
[pass] Password 81
[Pass] Password 78
[pas;u] User Password 78, 80
[p;dl] Peltier Delay 56
[`P;EE] Process Error Enable 48
[`P;EL] Process Error Low 48
[``pn] Part Number 82
[``Pn] Part Number 81
[poti] Power Out Time 46
[`pro] Process 49
[P;StA] Prole Status Menu 43
[P;tyP] Prole Type 66
[p;unt] Pressure Units 51
[``Pu] Process Value Menu 51
[`Pu;A] Process Value Active 38
[rAtE] Rate 77
[`rEu] Software Revision 81
[`r;hi] Range High 48, 61, 91
[``rh] Relative Humidty 49
[`r;Lo] Range Low 47, 61, 91
[rLoC] Read Lockout Security 80
[roll] Rolling Password 78, 80
[``rP] Ramp Action 58, 98
[`rP1] Ramping 27
[`rP1] Ramping 1 27
[`rP1] [`rP2] Ramping 1 or 2 27
[`r;rt] Ramp Rate 58, 98
[``r;r] Thermistor Resistance
Range 48
[`r;SC] Ramp Scale 58, 98
[`r;Sr] Retransmit Source 92
[`rt;L] RTD Leads 47
[`r;tp] Relative Temperature 49
[R;typ] Ramping Type 66
[S;bLd] Software Build 81
[`seC] 35
[`seC] Seconds 44
[`SEn] Sensor Type 47, 88, 90
[SFn;A] Source Function A 62
[`S;hi] Scale High 47, 60, 91, 92
[`Si;a] Event Input Source Instance
A 66
[`Si;B] Event Input Source Instance
B 66
[`SiL] Silence 100
[`S;Lo] Scale Low 47, 60, 91, 92
[SLoC] Set Lockout Security 80,
102, 103
[``Sn] Serial Number 81
[SoAh] Soak 77
[s;stp] Prole Start Step 54
[`StP] Active Step 43
[S;tyP] Active Step Type 43
[`Su;A] Source Value A 37
[subt] Synchronized Variable Time
Base 46
[t;Agr] User Tune Aggressiveness
56, 86
[t;bnd] TRU-TUNE+™ Band 56, 87
[``t;C] Thermistor Curve 48
[``td] Time Derivative 40, 55, 87,
96
[`t;gn] TRU-TUNE+™ Gain 56, 87
[``ti] Time 77
[``ti] Time Integral 40, 55, 87, 96
[t;tUn] TRU-TUNE+™ Enable 56,
87
[tUn1] Tuning 27
[tUn1] [tUn2] Tuning 1 or 2 27
[tUn1] Tuning 1 27
[uAL;h] Value to high 27
[`UFA] User Failure Action 57
[USr;r] User Restore Set 67, 85
[USr;S] User Save Set 67, 85
[UStP] Unused Step 77
[uAL;L] Value to low 27
[W;bo] Wait For Both 77
[WE;2] Wait Event 2 75
[2one] Zone 67
A
Absolute Temperature 49
AC Line Frequency 65, 98
Active Event Output (1 or 2) 44
Active Step 43
adaptive tuning 87
Address Modbus 68
Address Standard Bus 67, 68
Administrator Password 78, 81
agency approvals 3
alarm blocking 100
Alarm Menu 41, 61
alarms 99
Blocking 63, 100
deviation 99
Display 64
Hysteresis 62, 99
Latching 62, 100
Logic 62
process 99
set points 99
Sides 62
Silencing 63, 100
Source 62
Type 61
Alarm Type 99
Altitude Units 45
Analog Input Menu 36, 47
Assembly Denition
Addresses 112
Assembly Denition Addresses 104
Assembly Denition Addresses and
Assembly Working Addresses
112
Assembly Working Addresses 104,
112
Attention Codes 28
auto (closed loop) control 93, 94
Autotune 86
Autotune Aggressiveness 56
Autotune Set Point 39, 86
autotuning 86–87
autotuning with TRU-TUNE+™ 87
B
Baud Rate 68
Blocking 63, 100
bumpless transfer 94
C
Calibration Menu 82
Calibration Offset 36, 48, 61, 88–89
changing the set point 28
Channel 67
chattering output 94
chemical compatibility 13
CIP (Common Industrial Protocol)
33
Closed Loop Set Point 39, 58
Closed Loop Working Set Point 38
Communications Menu 67, 68, 74,
79
Setup Page 35, 45
Control 52, 59
Control Loop Menu 54
control methods 93
Control Mode 39, 58, 94
Control Mode Active 38
Control Module Menus
Factory Page
Calibration Menu 82
Security Setting Menu 79, 81
Operations Page
Alarm Menu 41
Analog Input Menu 36
Digital Input/Output Menu 38
Linearization Menu 36
Loop Menu 39
Monitor Menu 38
Process Value Menu 37
Prole Status Menu 43