User guide

Watlow EZ-ZONE
®
PM PID Controller • 120 • Appendix
Output Type 60, 92
P
P3T armor sealing system 3
Parameter 1 to 20 79
Parameter ID 33
Parity 68
Part Number 81, 82
Password 81
Password Enable 78
Peltier Delay 45, 56
Power Out Time 46, 66
Pressure Units 45
process alarms 99
Process Error Enable 48
Process Error Low 48
Process Value 36, 49, 51
Process Value Active 38, 39
Process Value Menu 37
Probus 34
Probus Index 33
Prole Setup 70
Prole Status Menu 43
Prole Type 66
Proling Page 70
proling parameters 73, 74
programming the Home Page 86
proportional control 95
plus integral (PI) control 96
plus integral plus derivative (PID)
control 96
Protocol 67
Public Key 78, 81, 82
Q
R
Ramp Action 58
Ramp Rate 58, 98
Ramp Scale 58, 98
Range High 48, 61, 91
Range Low 47, 61, 91
Rate 77
Real Time Clock 34, 46
Relative Humidty 49
Relative Temperature 49
removing mounted controller 12
responding to a displayed message
27–28
restoring user settings 85
retransmit 91, 92
Retransmit Source 60, 92
Rolling Password 78, 80
RTD Leads 47
S
saving user settings 84
Scale High 47, 60, 91, 92
Scale Low 47, 60, 91, 92
Seconds 74
Security Setting 79, 81
sensor selection 90
Sensor Type 47, 88, 90
Serial Number 81
set point high limit 90
Set Point High Limit Open Loop 58
set point low limit 90
Set Point Low Limit Open Loop 58
Setup Page 45
Sides
Alarm 62
Silencing 63, 100
single set point ramping 98
Soak 77
Software Build 81
Software Revision 81
Source 62
Starting a Prole 71
Synchronized Variable Time Base
46
T
Target Set Point 74
temperature units indicator lights 26
Thermistor 18, 47
Time 77
Time Base 52, 59
Time Derivative 40, 55, 87, 96
Time Integral 40, 55, 87, 96
TRU-TUNE+™ Band 56, 87
TRU-TUNE+™ Enable 56, 87
TRU-TUNE+™ Gain 56, 87
tuning the PID parameters 86
Type 61
U
Unused Step 77
upper display 26
User Failure Action 57
User Password 78, 80
User Save Set 85
User Tune Aggressiveness 86
Using EZ-ZONE® Congurator Soft-
ware 105
using the software 101
V
variable time base 97, 98
W
Wait Event (1 and 2) 75
Wait For Both 77
Wait For Process Instance 75
Wait For Time 74
weight 115
wiring
digital input or output 5 16
high power 16
input 1 potentiometer 17
input 1 process 17
input 1 RTD 17
input 1 thermocouple 17
input 2 thermocouple 18
low power 16
Modbus RTU or Standard Bus EIA-
485 communications 23
output 1 mechanical relay, form C
20
output 1 solid-state relay, form A
21
output 1 switched dc/open collector
19, 20
output 1 universal process 20
output 2 mechanical relay, form
A 22
output 2 no-arc relay, form A 22
output 2 solid-state relay, form A
22
output 2 switched DC/open collec-
tor 21
output 3 switched dc/open collec-
tor 23
Standard Bus EIA-485 communica-
tions 23
X
Y
Z
Zone Display 67