Use and Care Manual

Why waste pplying primers, glazes
21.25”
7.125”
1/2” NO PRINTING AREA
.5”
• OVERALL DIMENSION: 7 1/8” X 21 1/4”
• NO PRINTING AREA OF 1/2” TO ACCOMMODATE GLUE AREA OF LABEL
• GLUE LAP CAN BE ON EITHER END OF LABEL. DIFFERENT MACHINES USE DIFFERENT POSITIONS
• EAR HOLES ARE 1 3/8” IN DIAMETER. THEY ARE 10 1/4” APART, ON CENTER.
• IT IS BETWEEN THESE TWO HOLES THAT THE FRONT OF LABEL USUALLY FALLS.
DIRECTIONS COPY GOES HERE
FRONT COPY GOES HERE
10.25”
10.25”
7”
THIS TEMPLATE IS A GUIDE ONLY. YOUR ARTWORK SHOULD BE
COMPOSED TO FIT THE ACTUAL CAN YOU ARE FILLING AND THE
EQUIPMENT IT IS BEING APPLIED WITH.
1 GALLON COVERS APPROX. 325 SQ. FT. WWW.WEATHERWASHCOATINGS.COM
WOOD PREP Surface must be free of sealers, stains, & conditioners
before staining. Prepare wood for staining by sanding with 80 grit
sandpaper with the grain.
PRODUCT PREP MIX STAIN WELL before and during use to ensure
settled materials are re-dispersed. Do not thin. First, TEST an
INCONSPICUOUS SWATCH. For best results, store and use only
when temperature is between 60-90°F (16-32°C) and relative
humidity is below 85%. Do not store in metal containers.
COVERAGE 1 gallon treats 325 sq. ft. of smooth wood.
APPLICATION Use a foam roller, rag, brush, or paint sprayer to
apply one liberal coat of stain in the direction of the grain. Wood
will absorb stain and each species will turn its own darkest color.
Do NOT apply and wipe off. DRENCH the wood evenly
to ensure consistent color.
DRYING TIME Allow wood to dry 60 minutes. Longer dry times
for damp / humid climates, rough sawn & soft woods.
CLEAN UP Easy soap and water clean up.
FINISHES After a minimum of 1 hour apply your favorite
Weatherwash topcoat per the directions on the can.
CAUTIONS Do not take internally. Keep out of reach of children.
In case of eye contact flush with large amounts of water.
Get medical attention if irritation persists. If swallowed do
not induce vomiting. Get medical attention immediately.
Why waste hours applying primers, paints, and glazes
when you can actually age wood? Weatherwash PINED
is a tannin-based, reactive stain, which naturally ages
wood in minutes. Woods that are low in tannic acid will
yield a silvery gray, aged look in minutes instead of
centuries. Color results vary depending on wood
species and will create a natural-looking result without
compromising the grain. Weatherwash PINED can
be top-coated and will maintain color consistency.
AGE INDEX Use for a silvery weathered look
on LOW tannin woods.
SPECIES Low tannin woods including pine, poplar, white fir,
and spruce. See our color chart online.
USE For use on wood walls, ceilings, floors, cabinetry,
furniture, millwork, etc.
Water-Based
Top Coat Compatible
VOC Free
Non Toxic
Commercial & Residential
Interior
WARNING! Removal of old paint by sanding, scraping or other means may generate dust or fumes that contain lead.
Exposure to lead dust or fumes may cause brain damage or other adverse health effects, especially in children or
pregnant women. Controlling exposure to lead or other hazardous substances requires the use of proper protective
equipment such as a properly fitted respirator (NIOSH approved) and proper containment and cleanup. For more
information, call the National Lead Information Center at 1-800-424-LEAD (in US) or contact your local health authority.
DIRECTIONS
WEATHERWASH’S “BARNWOOD” PRODUCT OVERVIEW
Why waste hours applying primers, paints, and glazes when you can age wood in minutes?
Rusted is a tannin-based, reactive stains, that naturally ages wood. It is suitable for nearly all wood
types and yields deep weathered brown in minutes, instead of centuries. Unlike pigment based
stains, latex paints, or oil-based stains. Rusted won’t compromise the wood’s grain. Color results
depend on wood specie is and will create a natural-looking result from plank to plank. Stain can
be top coated to maintain color consistency.
AGE INDEX Turn wood into a beautiful barnwood brown tones. For more intense weathering,
apply multiple coats.
SPECIES Lightly weather all woods , especially pretty on hardwoods.
USE Interior use on wood walls, ceilings, floors, cabinetry, furniture, millwork, etc.
WOOD PREP Sand wood with the grain. Do not apply pretreaters.
PRODUCT PREP Mix stain well before and during use to ensure
settled materials are re-dispersed. Do not thin. First, test and
inconspicuous swatch. For best results, store and use only when
temperature is between 60-90°F (16-32°C) and relative humidity is
below 85%. Do not store in metal containers
COVERAGE 1 Gallon treats 400 sq. ft. of smooth wood.
APPLICATION Use a foam roller, brush or paint sprayer to apply one
liberal coat of stain in the direction of the grain. Wood will absorb
stain. Each species will turns its own darkest color. For exteriors,
stain may be applied on site but avoid contact with concrete or
siding.
For darker results, multiple coats may be applied.
DRYING TIME Allow wood to dry 60 minutes. Longer dry times for
damp/humid climates, rough sawn & soft woods.
CLEAN UP Easy soap and water clean-up.
FINISHES After a minimum of 1 hour apply your favorite
Weatherwash topcoat per the directions on the can.