Installation Guide

5
wedi Fundo
®
Primo  Tools needed for installation | Herramientas necesarias para la instalación | Des outils sont nécessaires pour l’installation
EN
ES
FR

Bucket
 Utility Knife
 Caulk Gun
 Flat Head Screwdriver
 Paper Towels
 Saw Horse
 Extension Cord for Powertools
 Speed Square
 Handsaw
 Solid Putty Knife
 Circular Saw
 Permanent Marker
 Safety Glasses
 wedi
®
Corner Putty Knife
 Respirator Mask (N95)
 Cubo  Taladro con mezcladora
 Cuchillo multiuso de mortero cola
 Escuadra triangular de acero  Serrucho
 Desarmador de punta plana  Espátula sólida
 Papel absorbente  Sierra circular
 Caballete  Rotulador permanente
 Cable de extensión para  Gafas de seguridad
herramientas eléctricas  Espátula para esquina wedi
 Seau  Perceuse avec mélangeur
 Couteau universel de ciment-colle
 Équerre triangulaire  Couteau à mastiquer rigide
 Tournevis à bout plat  Scie circulaire
 Essuie-tout  Marqueur permanent
 Chevalets  Lunettes de protection
 Rallonge pour outillage électrique  Couteau à mastiquer
 Masque respiratoire (N95)
 1/4 in. square Notch Trowel
 Straight Edge /
T Square 5 ft (1524 mm) or longer
 Screw gun w/ Phillips bit
 Level
 Tape Measure
 Shop vacuum cleaner
 Drill with Thinset Mixer
 Llana ranurada

Regla o regla T de al menos 5 ft (1524 mm)
 Pistola para calafatear
 Pistola atornilladora
 Nivel
 Cinta métrica
 Aspiradora de taller
 Máscara de respiración (N95)
 Truelle dentelée
 Règle/Équerre en T de (1524 mm) ou plus
 Pistolet à calfeutrer
 Pistolet à vis
 Niveau
 Mètre ruban
 Aspirateur d’atelier
 Scie égoïne les angles wedi
 Have 2 × 4‘s blocks installed on base plate between and ush with front of
wall framing studs to best support wedi wall panel / shower base transition.
 Suboor is stable and loadbearing, at and level, and meets deection crite-
ria of maximum L/360 as per IRC. Wooden or concrete structural substrates
are dry and sufciently loadbearing considering live and dead load. Wood
and Steel framing is sufciently loadbearing, even, plumb and square.

Floor drain assembly below oor is stabilized, xed and supported in po-
sition, and will not sink under water load. Waste pipe is level and plumb.

Only wedi products (Building Panels, Curb, Joint Sealant and Fasteners)
are used for wedi Fundo Shower System assembly.

Installer has received instructions from wedi technical sales staff or is in-
formed about proper installation methods as described.

wedi shower bases can be cut to size using a circular saw.
 Follow applicable state or local plumbing codes requiring specic and
dimensioned waterproofed areas for a shower system or other wet room
installation. Requirements in this manual supersede local plumbing codes;
they extend and are not in conict. wedi Shower Systems or other wet
room installations in which non-wedi product is also used require specic
project recommendations by wedi and may reduce the extent and installation
area of protection offered by wedi’s warranty.
EN
 Ensure that no fasteners are used and penetrate through any horizontal building
panel or shower base surfaces in shower or immediate wet rooms. This includes
tub decks, pony shower wall tops, curb tops made from building panels, seat
tops. wedi panels in such areas are installed in a full surface applied thinset
mortar setting bed.
 Seams in the assembly, which are not flat transitions or right angle inside corner
connections, are treated with these extra steps:
1) Assembly parts are installed tight and offer a minimum of 1/2 in. wide con-
tinuous contact/adhesion surface between two parts, inside which wedi
®
Joint Sealant is continuously applied.
2) wedi® Joint Sealant is applied over these seams topically, and 1 in. wide
on both sides of the seam.
3) wedi sealing tape is installed over these seams and covered with joint
sealant 1 in. wide on both sides of the seam.
Prepare the installation / installation site