Model AF/AFG Burners for Gold Oil Series High-efficiency Oil-fired Boilers Instruction Manual Type ‘M’ Air Tube Combination Type ‘L1’ Head Type ‘V1’ Head Potential for Fire, Smoke and Asphyxiation Hazards Incorrect installation, adjustment, or misuse of this burner could result in death, severe personal injury, or substantial property damage.
To the Owner: Thank you for purchasing a Beckett burner for use with your heating appliance. Please pay attention to the Safety Warnings contained within this instruction manual. Keep this manual for your records and provide it to your qualified service agency for use in professionally setting up and maintaining your oil burner. Contents General Information .................................................... 3 Hazard Definitions ........................................................................
Section: General Information General Information Owner’s Responsibility Hazard Definitions Indicates a hazardous situation, which, if not avoided, will result in death or serious injury. Indicates a hazardous situation, which, if not avoided, could result in death or serious injury. Incorrect installation, adjustment, and use of this burner could result in severe personal injury, death, or substantial property damage from fire, carbon monoxide poisoning, soot or explosion.
Section: General Information Do NOT Alter the Original Burner Design Tampering with or altering the burner design could seriously impair performance, resulting in loss of static pressure, damage to the system components, reduced air volume, heavy smoke, flame impingement, appliance sooting, hot gas puff-back, and asphyxiation or fire hazards. Maintain the design to its original configuration. Only use parts specified for AF or AFG Burners. Do NOT remove the air guide from the AFG chassis.
Section: General Information Table 2 - Air Tube Combination (ATC) codes Boiler Model Burner Spec. # Input / GPH Delavan Hago Monarch Steinen Danfoss Pump Pressure (PSIG) Burner Head Type Static Plate Drawer Setting Air Tube Combination Blower Size (“) Starting Air Shutter Position Starting Air Band Position Nozzle GPH/Type GO-2 WL-6202 0.70 0.75 x 70° B 0.75 x 70° ES 0.75 x 70° AR 0.75 x 70° S N/A 100 L1 3-3/8”U 1-3/8 AFG50MBAS 4-1/4 6 0 GO-3 WL-6203 0.95 0.85 x 45° B 0.
Section: Inspect/Prepare Installation Site Inspect/Prepare Installation Site Inspect Chimney or Direct Vent System piece of broken tile wedged in the chimney should be removed. 5. No other appliance connection should be made to the same flue pipe. Fire, Smoke & Asphyxiation Hazard 6. The flue pipe should have an upward pitch toward the chimney of at least 1/4” per foot of length. It should fit tightly and should not project into the chimney. y Carefully inspect the chimney or exhaust vent system.
Section: Inspect/Prepare Installation Site Combustion air supply Adequate Combustion and Ventilation Air Supply Required Failure to provide adequate air supply could seriously affect the burner performance and result in damage to the equipment, asphyxiation, explosion or fire hazards. y The burner cannot properly burn the fuel if it is not supplied with a reliable combustion air source.
Section: Prepare the Burner Prepare the Burner Table 4 - AFG Reduced Firing Rates (with LFRB) Burner head type Low Firing Rate Baffle installed F0 up to 0.65 gph F3 or L1 up to 0.85 gph F4 or F6 up to 0.90 gph V1 up to 1.00 gph Low Firing Rate Baffle The AFG Low Firing Rate Baffle (LFRB) reduces the air flow and pressure. The LFRB is sometimes used for firing rates under 1.00 gph as listed in Table 4. Refer to the appliance manufacturer’s instructions. Do not omit the LFRB when specified.
Section: Mount Burner on Appliance 3. If the nozzle is already installed, remove the nozzle line assembly to verify that the nozzle size and spray pattern are correct for the application (per appliance manufacturer’s information). Verify that the electrode tip settings comply with Figure 3. Figure 3. – Electrode Tip Adjustment Standard Dimensions for F, L1, and V1 Heads. 4.
Section: Mount Burner on Appliance Adjust the ‘Z’ dimension to the required specification. Table 7 - Burner Dimensions (Figure 4 thru 6) Dimension (inches) Incorrect Adjustments could cause combustion problems, carbon deposition from flame impingement, heavy smoke generation and fire hazard. Make all adjustments exactly as outlined in the following information.
Section: Mount Burner on Appliance Figure 5. Check/Adjust ‘Z’ Dimension - L1 & L2 Heads 2. Use the following procedure to adjust the “Z” dimension, if it is not correct: ○ ○ ○ ○ ○ ○ L1/L2 heads (see Table 7 and figure above for dimensions) 1. See figure above. The important “Z” dimension is the distance from the leading edge of the head to the end of the air tube. This distance for L1 & L2 heads is 1-3/8” if the tube has a straight shroud or 1-3/4” if the air tube has a conic shroud.
Section: Mount Burner on Appliance Figure 8. – Inside Tank Gravity Feed System Figure 7. – Mounting Burner in Appliance If space between burner air tube and opening exceeds 1/2 inch, pack burner opening with ceramic fiber refractory. Tilt down 2° SK8745 Installing the Oil Tank and Supply System Oil Leak and Fire Hazard Install the oil tank following applicable standards in the U.S. by referring to the latest edition of NFPA 31 or CSA-B139 & CSA-B140 in Canada, and all authorities having jurisdiction.
Section: Wire Burner Oil Supply Pressure Control Required Damage to the filter or pump seals could cause oil leakage and a fire hazard. Wire burner Burner packaged with appliance Electrical Shock Hazard y The oil supply inlet pressure to the burner cannot exceed 3 psig. Electrical shock can cause severe personal injury or death. y Insure that a pressure limiting device is installed in accordance with the latest edition of NFPA 31. y Do NOT install valves in the return line. (NFPA 31, Chapter 8.
Section: Burner Controls Burner Controls Wiring GeniSys Model 7505 Control Fire or Explosion Hazard Can cause severe injury, death, or property damage. y The control can malfunction if it gets wet, leading to accumulation of oil or explosive oil vapors. y Never install where water can flood, drip or condense on the control. y Never use a control that has been wet - replace it.
Section: Burner Controls Typical Burner Sequence of Operation for GeniSys 7505 Control. Refer to the appliance manufacturer’s wiring diagram for actual specifications. 9 1 Pump prime Standby 3 2 4 Trial for ignition Valve-on delay Lockout 5 Ignition carryover 6 8 Motor-off delay 1. Standby: The burner is idle, waiting for a call for heat. 2. Valve-On Delay: The igniter and motor are on while the control delays turning on the oil solenoid valve for the programmed time. 3.
Section: Burner Controls 60 70 SAFETY AND OPERATING LIMITS L1 R L2 60 70 60 70 W SAFETY AND OPERATING LIMITS 80 50 60 50 80 L2 W 80 50 L1 Figure 11b. – Interrupted ignition, valve-on delay and motor-off delay 70 R 50 80 Figure 11a.
Section: Burner Controls Figure 12 - Typical Burner Wiring & Burner Sequence of Operation for R7184P Control. Refer to the appliance manufacturer’s wiring diagram for actual specifications. 1. STANDBY. The burner is idle, waiting for a call for heat. When a call for heat is initiated, there is a 3-10 second delay while the control performs a safe start check. 2. VALVE-ON DELAY. The ignition and motor are turned on for a 15 second valve-on delay. 3. TRIAL FOR IGNITION (TFI). The fuel valve is opened.
Section: Start-up Burner/Set Combustion Wire Burner 3. Set the thermostat substantially above room temperature. Some Thermostats Are Polarity Sensitive. Reversed polarity could cause erratic cycling of the burner control. Connect the wire from the RH or R terminal on the thermostat to the TR terminal on the control. Connect the wire from the W terminal on the thermostat to the TW terminal on the control. 4. Close the line voltage switch to start the burner.
Section: Start-up Burner/Set Combustion ○ ○ Always verify the control functions according to all specifications before leaving the installation site. Replace the control if it does not operate as specified. mode. Verify that the green light is flashing. The control will remain in Recycle for 60 seconds. 4. After the 60 second recycle period, the control will try to restart the system. 5. After the 15 second lockout time, the control will lock out the burner and the reset button will flash.
Section: Perform Regular Maintenance Step 4: Recheck smoke level. It should be Zero. This procedure provides a margin of reserve air to accommodate variable conditions. If the draft level has changed, recheck the smoke and CO2 levels and readjust the burner if necessary. 4. Once combustion is set, tighten all fasteners on air band, air shutter and head adjusting plate or escutcheon plate. 5. Burner equipped with cover - Reinstall the cover and repeat Steps 2 and 4.
Section: Perform Regular Maintenance Replace the blower wheel: 1. Turn off all power to the burner before servicing. Figure 13. Blower wheel assembly 2. Disconnect the burner motor wires. 3. Remove the bolts securing the motor to the burner housing. 4. Remove the motor and blower wheel. 5. Remove the existing blower wheel. Use a Feeler Gauge to set the gap to; AF = 0.125 +1/64 inch AFG = 0.030 +1/64 inch 6. Referring to the figure below, slide the new blower wheel onto the shaft.
For best performance specify genuine Replacement Parts replacement parts These parts are unique to AF burners. Replace parts numbered 11 and 12 with the exact parts designated in the parts list.
Specify* 21807U 21887U 3 4 2454 31231U (AFG) 31841U (AF) 2999U (AFG) 2459U (AF) 21805U 4189 5770 10 11 12 13 14 Head Adjusting Plate (V1 head) 5941 2139 3493 8 9 Electrode Kit - F Head up to 9” 5780 Escutcheon (F & L1/L2 heads) 3666 7 Weil-McLain Gold Oil Series AF/AFG Burner Manual Electrical Box PSC Motor Mounting Screws Blower Wheel (AFG) Blower Wheel (AF) Air Guide (AFG) Air Inlet Bell (AF) Coupling Hole Plug Splined Nut Copper Oil Line - 8” 5685 25 2182602U Specify
Limited Warranty Information The R. W. BECKETT CORPORATION (“Beckett”) warrants to persons who purchase its “Products” from Beckett for resale, or for incorporation into a product for resale (“Customers”), that its equipment is free from defects in material and workmanship. To qualify for warranty benefits, products must be installed by a qualified service agency in full compliance with all codes and authorities having jurisdiction, and used within the tolerances of Beckett’s defined product specifications.