Installation AUTOMATIC Part No.
Changing The Bin Door And Lower Panels The storage bin door is designed to accept an optional decorative wood panel of your choice. The wood panel should be no more than l/4 inch (6 mm) thick. Cut it to the same size as the production metal panel. To change the bin door panel: I. Open the bin door. 2. Remove the two screws on top of the door which hold the handle. 3. Remove the handle and handle insert. 4. Slide the metal panel out. 5.
General Information Unpack 1. Lay carton on rear face and break open bottom flaps. 2. Set carton upright with all four flaps outward. 3. Lift carton up and off of machine. 4. Remove all tape and packaging materials from the outside and inside of the cabinet. 5. Remove the lower access panel by removing the two screws securing the grille at the bottom and the one screw at the top, and lift it free of cabinet. 6. Turn the fan by hand to make certain it moves freely. 7.
Level unit 1. After placing unit in position, check to make certain the unit is level side-to-side and front-to-back. 2. Accurate leveling is essential for proper operation. 3. Unit should be shimmed so that it is solid as well as level. The shims should be of hard permanent type material such as Masonite. 4.
Connect to drain (observe local codes) 1. The unit is provided with a gravity drain. 2. The ideal installation has a standpipe (1 -l/4” [32 mm] minimum) installed directly below the outlet of the drain tube. Refer to figures for the proper location of the standpipe. 3. It may be desirable to insulate drain line thoroughly up to drain inlet. Connect drain pump If a drain connection directly below the drain tube outlet is not available, install a drain pump in the rear compartment of the ice maker.
For The Electrician Electrical1 requirements A 115 Volt, 60 Hz., AC only, 15 or 20 ampere electrical supply circuit, properly grounded in accordance with the National Electrical Code and local codes and ordinances is required. Grounding method ! AA It is recommended that a separate circuit, serving only this appliance, be provided. Use a receptacle which cannot be turned off with a switch of pull chain. DO NOT use an extension cord.
How The Ice Maker Compressor runs . Condenser fan runs l Water pump runs (circulates water) l Cutter grid is warm to touch l WHEN THE DESIRED ICE SLAB THICKNESS IS REACHED, THE HARVEST CYCLE BEGINS AND THE FOLLOWING HAPPENS: l Evaporator thermostat is satisfied .
Operating Instructions For complete operation information, refer to the Use and Care Guide. Before starting, wash out interior of cabinet with a Baking Soda solution (2 tablespoons [26 grams] soda to 1 quart [l liter] of warm water). Rinse thoroughly. Make certain the water is turned on. Turn switch to the “ON” position. l l l l CUBELET GRID 3/4” x 3/i” (19 mm x 19 mm) IMPORTANT: Allow unit to run for 3 hours before expecting ice and for 24 hours before trying to set the thickness control.
Check Operation Start the unit by turning the service switch to “ON” and opening the line water valve. d NOTE: Left is “OFF” - Middle is “ON” Right is “CLEAN.” In “CLEAN” position, only the pump operates. Check condenser fan to make sure it is revolving. Check for airflow. Do not insert hand into fan area. Check for even water flow over freezing plate. Unit must be level for proper operation. Check for desired cube thickness and after 24 hours adjust if necessary.
d’installation MACHINE Pike no2180913 A GLACONS Changement du panneau de la Porte du receptacle et du panneau inferieur 2 Renseignements generaux 3 Instructions a I’intention du plombier 4 Instructions a I’intention de I’electricien 6 Mode de fonctionnement 7 Ne pas oublier 7 Instructions d’utilisation 8 Schema de cdblage 8 Controle du fonctionnement g AUTOMATIQUE
Changement du panneau de la Porte du rkeptacle du panneau inferietir et La Porte du rkeptacle 2 glaGons peut recevoir un panneau dkcoratif en bois (facultatif) choisi par I’utilisateur. L’Bpaisseur du panneau en bois ne doit pas dbpasser 6 mm (‘I4 PO). DBcouper le panneau aux m&mes dimensions que le panneau mktallique d’origine. Pour changer le panneau de la Porte du rkeptacle : 1. Ouvrir la Porte du rkeptacle. 2. &er les deux vis de fixation de la poignke, en haut de la Porte. 3.
Renseianements - cwh6raux Dbballage 1. Placer la boite en appui sur la face arriere, et ouvrir les rabats du fond. 2. Placer la boite verticalement, en veillant a ecarter les rabats. 3. Soulever la boite en carton pour degager la machine. 4. Retirer tous les rubans adhesifs et materiaux d’emballage a I’exterieur et a I’interieur de la caisse. 5. &er le panneau d’acces inferieur; pour cela, oter les deux vis fixant la grille en bas, et une vis au sommet; soulever pour &parer le panneau de la caisse. 6.
Mise d’aplomb 1. Apres avoir place I‘appareil a l’emplacement d’installation, controler I’aplomb, lateralement et d’avant en arriere. 2. Un reglage p&is de I’aplomb de I’appareil est essentiel pour un fonctionnement convenable. 3. Si c’est necessaire, placer des tales afin que I’appareil soit d’aplomb et repose bien sur les quatre pieds. Utiliser pour les tales un materiel a rigidite permanente comme Masonite. Instructions plombier 4.
Raccordement (observer B I’hgout les dispositions des codes 1. L’appareil est dote d’un systeme de d&charge a l’egout, par gravite. 2. L’installation ideale comporte un tuyau d’evacuation (minimum 32 mm [I % PO]) installe directement au-dessous de I‘orifice de decharge du tube de decharge. Voir les Raccordement l schemas pour I’emplacement convenable du tuyau d’evacuation. 3. II peut etre utile d’isoler parfaitement la canalisation d’evacuation, jusqu‘a I’orifice de decharge.
Instructions Wlectricien Spkifications de I’alimentation Cet appareil doit etre alimente par un circuit de 115 volts, 60 Hz. CA seulement, 15 ou 20 amperes, convenablement relic ti la terre conformement aux dispositions du Code national des installations electriques, et aux codes et reglements locaux. M6thode de & I’intention de liaison klectrique On recommande I’emploi d’un circuit d’alimentation independant, ne desservant que cet appareil.
Mode de fonctionnement 0 Compresseur en marche 9 Ventilateur du condenseur en marche * Pompe B eau en rrarche (circulation de I’eau) l Grille de decoupage tiede au toucher * L‘electrovanne de I’entree d’eau s’ouvre 0 L’exces d’eau est rejete dans le plateau de collecte/drainage l La grille de decoupage est tiede au toucher LORSQUE L’CPAISSEUR Dl%IR~E DE LA PLAQUE DE GLACE EST ATTEINTE, LE PROCESSUS DE COLLECTE DES GLACONS DkBUTE, ET ON PEUT OBSERVER LES OPkRATIONS SUIVANTES : REMARQUE : La duree de I’ope
Instructions d’utilisation . Au sujet des instructions detaillees, voir le Guide d’utilisation et d’entretien. l Avant la mise en marche de I’appareil, laver les surfaces interieures avec une solution de bicarbonate de sodium (26 g [2 c. a soupe] de bicarbonate dans 1 litre [l pinte] d’eau tiede). Rincer parfaitement. l Verifier que I’arrivee d’eau est ouverte. l Placer le commutateur de commande a la position de MARCHE (ON).
Contr6le du fonctionnement Pour la mise en marche de I’appareil. placer le commutateur a la position de MARCHE (ON) et ouvrir le robinet d’arrivee d’eau. REMARUUE : Position de gauche OFF = ARRET, position mediane ON = MARCHE, position de droite CLEAN = NETTOYAGE. A la position CLEAN, seule la pompe fonctionne. Verifier visuellement que le ventilateur du condenseur tourne. Controler le debit d’air. Ne pas introduire la main dans la zone du ventilateur.