Thin Twin WasheraDryer - 240 Volt Installation Instructions IMPORTANT: Read and save . her IS . IMPORTANT: Installer: Leave Installation Instructions with the homeowner. Homeowner: Keep Installation Instructic Ins for future reference. Save Installation Instructions for local electrical inspector’s use.
Before you start... Do Not Store or operate washer/dryer below 32°F (some water may remain in washer). Proper operation of dryer cycles requires temperatures above 4S’F. See Use & Care Guide for “Winterizing” information. Check code requirements: Some codes limit or Do Not permit installation of clothes dryers in garages, closets, mobile homes and sleeping quarters. Contact your local building inspector. Check location where washer/dryer will be installed. Proper installation is your responsibility.
For use where local codes permit use of flexible power supply cord. four-wire receptacle(l4-30R) Figure 3 Where local codes permit connecting cabinetrounding three-wire receptacle(lO-30R) conductor Figure 4 Four-wire insfallufion is recommended (required for mobile homes): The power supply cord must have four, No.-1 0 copper wires and match a four-wire receptacle of NEMA Type 14-30R (see Figure 3).
Exhaust requirements center silver-colored block screw \ terminal neutral (white 01 center) Efl,appliance 3Y/ e] St@+) cabinet---...-. grounding connector Figure 11 4. Install copper, three-wire power supply cable through strain relief. 5. Slide the hook end of the neutral (white or center) wire from the three-wire power supply cable under the center, silver-colored terminal screw of the terminal block. Squeeze the hook end of the wire together. Tighten screw. 6.
The exhaust duct can be routed up, down, left, right or straight out the back of the washer/dryer. Space requirements are provided on Panel G and on the rear panel of the washer/dryer. Use the straightest b path you can to avoid 90” turns. ’ Mobile home installation This washer/dryer is suitable for mobile home installations.
Do Not Remove 9 n Remove the two rear corner posts located at the back of the washer/dryer* Remove the two corner pieces attached to the lower front of the washer/dryer. DO Not remove the foam shipping pieces between the washer and dryer until the washer/dryer is in place, Numbers CarreSDOnd rear comer posts to steljs. I 10 n Move foam shipping pieces outward just enough to clear the washer lid. Open the washer lid. The latch under the dryer will hold lid open. Pull ig$& p . . -- .
Move washer/dryer to its permanent location. Remove cardboard/hardboard from under washer/dryer. 23 n Carefullv move the washer/dryer into final position. Tilt the washer/dryer forward, raising back legs 1 inch off the floor so that the rear self-leveling legs will adjust. Gently lower the washer/dryer to the floor. Check that the washer/dryer is level by placing a carpenter’s level on top of the washer, first side to side. then front to back. - If it is not level, adjust the front legs up or down.
Recessed and closet installation instructions Product dimensions Recessed and closet :nstalIation nstructfons (Shown wlth legs extended bottom ot washer/dryer.) L-1 24" Recessed installation 12' r* . --I 3” j c Fire Hazard It is recommended that the washer/dryer be exhausted to the outside. If washer/dryer is installed in a closet, the dryer MUST be exhausted outside. Failure to do so may result in a fire.
If washer/dryer not operate., does Check the following to be sure that: 1. Electrical supply is connected. 2. House fuse or circuit breaker is intact and tight. 3. Washer lid or dryer door is closed, 4. Controls are set in a running or “ON” position. 5. Dryer start button has been firmly pushed. 6. Three shipping straps have been completely removed. Part No. 3397612 01995 When moving the washer/dryer.. . l l l l Disconnect the power supply cord, then tape securely to the washer/dryer.