Installation

12
Washer Diagnostic Mode
To enter the “Washer Diagnostic Mode,” first enter “Start
Operating Set-up.” Then press and hold the DELICATES/KNITS
key pad for 1 second while in set-up code 6, anytime a
diagnostic code is present.
On entry to diagnostic mode the
entire display will flash, a
cycle in process is canceled, money in escrow is cleared, and
diagn
ostic codes are cleared. If a diagnostic code persists,
it must be corrected before the following cycle options
are permitted.
There are five possible ways to initiate cycle activity from
diagnostic mode as follows:
1. W
asher Cleanout cycle - With the entire display flashing, this
cycle is started by pressing the BRIGHTS key pad.
Use the Washer Cleanout cycle once a month to keep the
inside
of your washer fresh and clean. This cycle uses a
higher water level. Use with liquid chlorine bleach to
thoroughly clean the inside of the washer. This cycle should
not be interrupted.
IMPORTANT: Do not place garments
or other items in the
washer during the Washer Cleanout cycle. Use this cycle with
an empty wash drum.
2. Ma
nual Overview Test - With the entire display flashing, this
cycle is started by pressing the WHITES key pad. This cycle
provides more typical full length fills, tumbles, drains, and
actuator dispenser movement, allowing for a more thorough
analysis of the washer operation, including pressure switch
behavior.
3. Qu
ick Spin Cycle - With the entire display flashing, this cycle
is started by pressing the COLORS key pad. This cycle
provides a method to quickly drain and spin (remove water
from the washer) if desired.
4. Quick Overview Test - With the entire display flashing, this
cycle is started by pressing the WOOLENS key pad. This
cycle provides a quick verification that the cold and hot water
valves, dispensers, and pump motor are working, as well as
actuator dispenser movement. It also includes door lock,
drain, and spin operations.
Pressing the DELICATES/KNITS key
pad will exit diagnostic
mode and cancel a diagnostic cycle in process.
DIAGNOSTIC CODES
If one of the following has occurred, the appropriate diagnostic
code will be in the display.
d9 Low voltage detected for 8 seconds.
F20 Slow Fill. The washer will not
detect water input for
4 min. Pressure switch failure or no water inlet. This
code is
reported as d8 on d7.
F22 The door is not able to lock. Door lock error or
someone tr
ying to start the washer, by pressing the
door switch with their finger.
(For any other display consult service personnel)
SERVICE ACCESS CODE
This code can be entered to access service mode without
removing the console. If the washer is not in failure mode, the
door must be opened to proceed. Service Access Code contains
6 steps and some are timed. Using only the three bottom buttons
(numbered 1, 2, and 3 from left to right):
1. Pr
ess 2 for longer than 2 seconds but less than 10 seconds.
2. Press 1 & 3 together for 2 seconds, then release. Displays S 3.
3. Press 1 & 2 together, then release. Displays S 4.
4. Press 2 & 3 together, then release. Displays S 5.
5. Press 2, then release. Display shows “codE”.
6. W
ait at least 2 seconds, but not more than 15 seconds, then
press in succession: 3, 2, 1, 3.
NOTE: If
the Service Access Code procedure is not completed
properly, as noted above, there is a 15 second delay before it can
be attempted again.
When the Service Access Code is used, there are 3 options
to exit.
1. Fr
om Set-up Code 8, press key #1 for 4 seconds.
2. Wait 2 minutes without touching any keypads (without
diagnostic modes running).
3. Power
down the washer, then reapply power.
WASHER HELP MODE
This mode is entered by pressing the PERM PRESS key pad
while in Set-up option code 2.XX.
In help mode, other display symb
ols and elements are mapped
to reflect the state of various inputs a
nd outputs as follows:
Display Symbol Description
Wash Water sensed at wash level.
*
Low voltage present (below about
90 VAC).
° (Circle above digit) Door closed.
DOOR LOCKED Door sensed locked.
COLD Cold water relay on.
HOT Hot water relay on.
OR Door unlock.
AVAILABLE Drain pump ON.
NOTE:
A technical sheet is supplied taped to inside of lower front
panel, which includes fault codes and a machine schmatic diagram.