Instruction for Use

ManualsBrandsWhirlpool ManualsDomestic AppliancesADG 9930

Whirlpool is a registered trademark of Whirlpool USA

Before using the dishwasher, read the

installation and maintenance instructions carefully!

5019 396 01174

ADG 9930

1) Programme data obtained in conformity with European standard EN 50242. The data may vary, for example, according to different loads,

extra functions, sensor settings (only with sensor programmes), water supply temperatures, water hardness and power supply voltage.

2) Energy label programme in compliance with EN 50242. - Information for Test Laboratories:

for more detailed information on the EN

comparison test and other tests, contact the following address: “nk_customer@whirlpool.com”.

3) The antibacterial action has been tested by the Institut Pasteur of Lille (France), based on the NF EN 13697 standard of November 2001.

1. OVERVIEW

On button

Off button

Programme selection button

Press button P (repeatedly) until the required

programme number appears on the display.

Fault indication and wash time display

In normal operation it indicates the remaining time

(h:mm), whereas with “Delayed start” selected it

indicates the time remaining until programme start (hh).

In the presence of a fault indication “F..” –, consult the

section “5. What to do if…”.

An acoustic signal sounds as long as the error persists.

Rinse aid level indicator and salt level indicator

They light up when rinse aid or salt need to be added.

Add just before starting a wash cycle.

Set the detergent

Press button P (repeatedly) to set the type of detergent used.

This deactivates the rinse aid and/or salt indicator.

Half Load/Multizone button

Load the upper or lower rack only.

Press once = wash upper rack (the indicator/symbol lights up)

Press twice = wash

lower rack

(the indicator/symbol lights up)

Press 3 times = Off (Half load/Multizone deactivated).

When washing without the upper rack, press the “Half

load” (i.e. “wash bottom rack”) button twice (the

corresponding indicator/symbol lights up).

Powder, gel, tablets (standard): indicator off

Detergent with rinse aid: left indicator

Detergent with salt + rinse aid: right indicator

“Delayed start” button

Press the button (repeatedly) to delay the start of the

programme. Adjustable from 1 to 24 hours. With each

press of the button, the delayed start indicator increases by

one hour and after 24 restarts from 00. Then press the

START button. The dishwasher will start after the set time.

START button

The indicator lights up during operation, flashes when a

fault occurs, and goes off at the end of the programme.

RESET button - for programme change or indication of faults

Press this button to cancel a started programme and

selected extra functions. Press this button to cancel the

main fault indicators (F..); also refer to the section “5.

What to do if...”. The programme can then be selected

and started.

Running programme indicator

A LED light projected on the floor indicates that the

dishwasher is working.

Table 1.1.

Table of programmes

Detergent

dispenser

Consumption

Programmes

Selectable

extra

functions

Loading instructions

large small Litres kWh Minutes

Sensor + 40-70°C

Normally or very soiled crockery, including

pots and pans

X X 7-17 0.99-1.58 65-170 ±

Pre-Rinse cold

Crockery to be washed later. — — 4.0 0.03 14±

Glasses 40°C

Light soiling, for example glasses and cups. X — 10.0 0.85 100 ±

Quickwash 40°C

Slightly soiled crockery, without dry

residuals.

X — 10.0 0.65 30 ±

Bio

50°C

Normally soiled crockery. Energy-saving

programme.

X X 11.0 1.05 170 ±

Hygienic +

Normally or heavily soiled crockery, with

additional antibacterial wash. Programme

interruption (e.g due to door opening) can

compromise elimination of germs.

X X 13.0 1.50 115 ±

Summary of content (8 pages)

PAGE 1
Before using the dishwasher, read the installation and maintenance instructions carefully! GB ADG 9930 1. OVERVIEW On button Off button Programme selection button Press button P (repeatedly) until the required programme number appears on the display. Fault indication and wash time display In normal operation it indicates the remaining time (h:mm), whereas with “Delayed start” selected it indicates the time remaining until programme start (hh). In the presence of a fault indication “F..
PAGE 2
. QUICK REFERENCE GUIDE Detailed instructions are given in the following pages, see also chapter “5. What to do if...” 1. Switch on the appliance Open the dishwasher door. Press the ON button. 2. Select a programme Press the button or to bring up the desired programme on the display. Select options, if available. 3. Select the type of detergent The detergent selection procedure varies depending on the dishwasher model. Chapter “1. Overview” provides instructions for selecting detergent type. 4.
PAGE 3
. HOW TO USE THE APPLIANCE PROGRAMME SELECTION Press the button or to bring up the desired programme on the display. The appliance must be switched on. If required, select options (if supplied). The corresponding indicator lamp switches on. Appropriate programmes and relative available options are detailed in table 1.1 on page 1. Programme times stated in the table were obtained under normal conditions and may vary depending on conditions.
PAGE 4
3. HOW TO USE THE APPLIANCE c. How to adjust the rinse aid dosage regulator The rinse aid dosage can be adjusted to the detergent used. The lower the setting, the less rinse aid is dispensed (factory setting: position 4). Press the button 2 to open the cover. Using a coin or similar object, turn the arrow to the desired setting. After adjusting the rinse aid setting, shut the cover again. If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3).
PAGE 5
3. HOW TO USE THE APPLIANCE HOW TO LOAD THE RACKS CUTLERY RACK: May be used in two different positions. Position 1 Position 2 In position 2 the upper rack must be lowered (see “Upper rack height adjustment” C below). For optimum washing results, position cutlery as shown (handles of spoons facing inwards). Beware of sharp/pointed items. Risk of injury! Cutlery holder A A May be removed individually, depending on upper rack load.
PAGE 6
4. PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Packing The packaging materials are 100% recyclable and marked with the recycling symbol. . 2. Removing the packaging and inspecting the contents After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt, contact a qualified technician or your local retailer. 3. Before using the dishwasher for the first time - The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
PAGE 7
5. WHAT TO DO IF... If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem. Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation. The appliance... Possible causes/solutions ...is not working/will not start - The appliance must be switched on. Check the household circuit fuse if there is no power supply. The dishwasher door must be closed.
PAGE 8
5. WHAT TO DO IF... Crockery and cutlery ... Possible causes/solutions ...are not perfectly clean/have food residues - ...have deposits: - regeneration salt residue - In the event of frequent use of low temperature programmes (50°C or lower) (if available), every now and again select a higher temperature programme The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see the instructions in “Maintenance and installation”).