Istruzioni per l’uso LAVASCIUGA ! Questo simbolo ti ricorda di leggere questo libretto istruzioni.
Installazione IT ! È importante conservare questo libretto per poterlo consultare in ogni momento. In caso di vendita, di cessione o di trasloco, assicurarsi che resti insieme alla lavasciuga per informare il nuovo proprietario sul funzionamento e sui relativi avvertimenti. mento dà stabilità alla macchina ed evita vibrazioni, rumori e spostamenti durante il funzionamento.
Collegamento del tubo di scarico Collegare il tubo di scarico, senza piegarlo, a una conduttura di scarico o a uno scarico a muro 65 - 100 cm posti tra 65 e 100 cm da terra; Attenzione! L’azienda declina ogni responsabilità qualora queste norme non vengano rispettate. IT Primo ciclo di lavaggio Dopo l’installazione, prima dell’uso, effettuare un ciclo di lavaggio con detersivo e senza biancheria impostando il programma “Auto Pulizia” (vedi “Pulire la lavasciuga”).
Manutenzione e cura IT Escludere acqua e corrente elettrica Pulire la pompa • Chiudere il rubinetto dell’acqua dopo ogni lavaggio. Si limita così l’usura dell’impianto idraulico della lavasciuga e si elimina il pericolo di perdite. • Staccare la spina della corrente quando si pulisce la lavasciuga e durante i lavori di manutenzione. La macchina è dotata di una pompa autopulente che non ha bisogno di manutenzione.
Precauzioni e consigli ! La lavasciuga è stata progettata e costruita in conformità alle norme internazionali di sicurezza. Queste avvertenze sono fornite per ragioni di sicurezza e devono essere lette attentamente. Sicurezza generale • Questo apparecchio è stato concepito esclusiva- mente per un uso di tipo domestico.
Descrizione della lavasciuga IT Pannello di controllo Tasto ON/OFF Tasto TIPO DI LAVAGGIO Tasto ASCIUGATURA DISPLAY Tasti Cassetto dei detersivi SELETTORE PROGRAMMI Tasto Tasto con spia MEMO START/PAUSE Tasti FUNZIONE Tasto Tasto TIPO DI RISCIACQUO TEMPERATURA Tasto Tasto PARTENZA PROGRAMMATA Cassetto dei detersivi: per caricare detersivi e additivi (vedi “Detersivi e biancheria”). Tasto ON/OFF : premere brevemente il tasto per accendere o spegnere la macchina.
Display IT Z B A X D C E Y F Il display è utile per programmare la macchina e fornisce molteplici informazioni. Nelle due stringhe superiori A e B vengono visualizzati il programma di lavaggio o il tipo di asciugatura selezionata, la fase di lavaggio in corso (il livello di asciugatura o il tempo di asciugatura selezionato) e tutte le indicazioni relative allo stato d’avanzamento del programma.
Come effettuare un ciclo di lavaggio e/o asciugatura IT 1. ACCENDERE LA MACCHINA. Premere il tasto , sul display comparirà la scritta “ACCENSIONE IN CORSO”; la spia START/PAUSE lampeggia lentamente di colore verde. 2. CARICARE LA BIANCHERIA. Aprire la porta oblò. Caricare la biancheria facendo attenzione a non superare la quantità di carico indicata nella tabella programmi della pagina seguente. 3. DOSARE IL DETERSIVO.
Programmi e funzioni Tabella dei programmi Asciugatura Lavaggio Candeggina Ammobidente Carico max. (Kg) 1 Antimacchia (1° pressione del tasto) 1 Antimacchia Rapido (2° pressione del tasto) 1400 1200 - 5 4,5 2 1400 9 1400 1400 1400 1000 - 9 9 9 4 Programmi Velocità max. (giri al minuto) Temp. max.
Detersivi e biancheria IT Cassetto dei detersivi Il buon risultato del lavaggio dipende anche dal corretto dosaggio del detersivo: eccedendo non si lava in modo più efficace e si contribuisce a incrostare le parti interne della lavasciuga e a inquinare l’ambiente. ! Non usare detersivi per il lavaggio a mano, perché formano troppa schiuma. Estrarre il cassetto dei deA B tersivi e inserire il detersivo o 3 l’additivo come segue.
Anomalie e rimedi Può accadere che la lavasciuga non funzioni. Prima di telefonare all’Assistenza (vedi “Assistenza”), controllare che non si tratti di un problema facilmente risolvibile aiutandosi con il seguente elenco. Anomalie: Possibili cause / Soluzione: La lavasciuga non si accende. • La spina non è inserita nella presa della corrente, o non abbastanza da fare contatto. • In casa non c’è corrente. Il ciclo di lavaggio non inizia. • • • • • L’oblò non è ben chiuso.
Assistenza IT Prima di contattare l’Assistenza: • Verificare se l’anomalia può essere risolta da soli (vedi “Anomalie e rimedi”); • Riavviare il programma per controllare se l’inconveniente è stato ovviato; • In caso negativo, contattare il Numero Unico 199.199.199*. ! Non ricorrere mai a tecnici non autorizzati. Comunicare: • il tipo di anomalia; • il modello della macchina (Mod.
Instructions for use WASHER-DRYER ! This symbol reminds you to read this instruction manual.
Installation GB ! This instruction manual should be kept in a safe place for future reference. If the washerdryer is sold, transferred or moved, make sure that the instruction manual remains with the machine so that the new owner is able to familiarise himself/herself with its operation and features. ! Read these instructions carefully: they contain vital information relating to the safe installation and operation of the appliance.
Connecting the drain hose 65 - 100 cm Connect the drain hose, without bending it, to a drain duct or a wall drain situated between 65 and 100 cm from the floor; Warning! The company shall not be held responsible in the event that these standards are not observed. The first wash cycle Once the appliance has been installed, and before you use it for the first time, run a wash cycle with detergent and no laundry, using wash cycle number auto clean (see “Cleaning the washer-dryer”).
Care and maintenance GB Cutting off the water and electricity supplies Caring for the door and drum of your appliance • Turn off the water tap after every wash cycle. This will limit wear on the hydraulic system inside the washer-dryer and help to prevent leaks. • Always leave the porthole door ajar in order to prevent unpleasant odours from forming. • Unplug the washer-dryer when cleaning it and during all maintenance work.
Precautions and tips ! This washer-dryer was designed and constructed in accordance with international safety regulations. The following information is provided for safety reasons and must therefore be read carefully. General safety • This appliance was designed for domestic use only.
Description of the washer-dryer GB Control panel CLEANING ACTION ON/OFF button button DRYING button DISPLAY Detergent dispenser drawer WASH CYCLE SELECTOR MEMORY button START/PAUSE button with indicator light FUNCTION buttons buttons ANTI ALLERGY RINSE button Detergent dispenser drawer: used to dispense detergents and washing additives (see “Detergents and laundry”). ON/OFF button : press this briefly to switch the machine on or off.
Display GB Z B A X D C E Y F The display is useful when programming the machine and provides a great deal of information. The upper two strings A and B are used to display the selected wash cycle or the type of drying selected, the current wash cycle phase (the selected dryness level or drying time) and all the indications relating to the progress status of the cycle.
How to run a wash cycle or a drying cycle GB 1. SWITCH THE MACHINE ON. Press the On/Off button ; the text POWER ON will appear on the display and the START/PAUSE indicator light will flash slowly in a green colour. 2. LOAD THE LAUNDRY. Open the porthole door. Load the laundry, making sure you do not exceed the maximum load value indicated in the table of programmes on the following page. 3. MEASURE OUT THE DETERGENT.
Wash cycles and functions GB Max. speed (rpm) Bleach Fabric softener Max. Cycle load duration (kg) Max. temp. (°C) Wash Detergents Drying Wash cycles Table of wash cycles 40° 1400 - 5 40° 40° (Max.
Detergents and laundry GB Detergent dispenser drawer Good washing results also depend on the correct dose of detergent: adding too much detergent will not necessarily result in a more efficient wash, and may in fact cause a build up on the inside of your appliance and contribute to environmental pollution. ! Do not use hand washing detergents because these create too much foam. A B MAX 2 3 Open the detergent dispenser drawer and pour in the detergent or washing additive, as follows.
Troubleshooting Your washer-dryer could fail to work. Before contacting the Technical Assistance Centre (see “Assistance”), make sure that the problem cannot be solved easily using the following list. GB Problem: Possible causes / Solutions: The washer-dryer does not switch on. • The appliance is not plugged into the socket fully, or is not making contact. • There is no power in the house. The wash cycle does not start. • • • • • The washer-dryer door is not closed properly.
Service 195130957.01 04/2015 - Xerox Fabriano GB Before calling for Assistance: • Check whether you can solve the problem alone (see “Troubleshooting”); • Restart the programme to check whether the problem has been solved; • If this is not the case, contact an authorised Technical Assistance Centre using the telephone number provided on the guarantee certificate. ! Always request the assistance of authorised technicians.