Health and safety

EN
3. Unscrew the burner fastening
screws.
4. Remove screw “V” and then
the oven burner.
V
5. Unscrew the oven burner
nozzle using the special socket
spanner for the nozzles, or
better still a 7 mm socket
spanner, and replace it with a
nozzle suited to the new type of
gas (see Table 1).
6. Replace all the parts,
following the steps described
above in the reverse order.
Take care to replace also the
bottomof the oven in its original
position.
Installation and repairs must be
carried out by a qualied
technician, in compliance with
the manufacturer’s instructions
and local safety regulations. Do
not repair or replace any part of
the appliance unless specically
stated in the user manual.
Children should not perform
installation operations. Keep
children away during
installation. Keep the packaging
materials (plastic bags,
polystyrene parts, etc.) out of
reach of children, during and
after the installation.
After unpacking the appliance,
make sure that it has not been
damaged during transport. In
the event of problems, contact
the dealer or your nearest After-
sales Service.
The appliance must be
disconnected from the power
supply before any installation
operation.
During installation, make sure
the appliance does not damage
the power cable.
Only activate the appliance
when the installation has been
completed.
After installation, the bottom of
the appliance must no longer be
accessible.
Carry out all cabinet cutting
works before tting the
appliance in the furniture and
carefully remove all wood chips
and sawdust.
Do not obstruct the minimum
gap between the worktop and
the upper edge of the oven.
Only remove the oven from its
polystyrene foam base at the
time of installation.
Do not install the appliance
behind a decorative door - Risk
of re.
ELECTRICAL WARNINGS
For installation to comply with
current safety regulations, an
omnipolar switch with minimum
contact gap of 3 mm is required
and the appliance must be
earthed.
If the power cable is damaged,
replace with an identical one.
The power cable must only be
replaced by a qualied
technician in compliance with
the manufacturer instruction
and current safety regulations.
Contact an authorized service
center.
It must be possible to
disconnect the appliance from
the power supply by unplugging
it if plug is accessible, or by
means of an accessible multi-
pole switch installed upstream
of the socket in conformity with
national electrical safety
standards.
The rating plate is on the front
edge of the oven (visible when
the door is open).
In case of replacement of power
cable, contact an authorized
service center.
IMPORTANT: The data rilevant
to the voltage an power
absortions are indicated on the
rating plate
If the tted plug is not suitable
for your socket outlet, contact a
qualied technician.
The power cable must be long
enough to connect the
appliance, once tted in its
housing, to the main power
supply. Do not pull the power
supply cable.
Do not use extension leads,
multiple sockets or adapters.
Do not operate this appliance if
it has a damaged mains cord or
plug, if it is not working
properly, or if it has been
damaged or dropped. Keep the
cord away from hot surfaces.
The electrical components must
not be accessible to the user
after installation.
Do not touch the appliance with
any wet part of the body and do
not operate it when barefoot.
The power cable must be long
enough to connect the
appliance, once tted in its
housing, to the main power
supply. Do not pull the power
supply cable.
The earthing of this appliance is
compulsory by law.
The cable must be checked
regularly and replaced by
authorised tschnicians in
compliance with the
manufacturer instruction and
current safety regulations.
CORRECT USE
Should you experience diculty
in turning the burners knobs,
please contact After Sales
Service for replacement of the
burner tap if found to be faulty.
The openings use for the
ventilation and dispersion of
heat must never be covered.
When you place the rack inside,
make sure that the stop is
directed upwards and in the
back of the cavity.
CLEANING AND
MAINTENANCE
Never use steam cleaning