FR-BE GB Instructions for use
Important safety instructions 4 Product description and symbols 7 Gas burner functions 7 Practical advice on how to use the burners 8 Injectors table 8 Induction zone functions 9 Positioning the pan supports and Wok support 10 Sizes and installation measurements (mm) 11 Safeguarding the environment 12 EC Declaration of conformity 13 Installation 13 Gas connection 14 Electrical connection 14 Securing the hob into cabinetry 15 Adaption to different kinds of gas 15 Replacing the i
IMPORTANT SAFETY INSTRUCTIONS YOUR SAFETY AND THAT OF OTHERS IS VERY IMPORTANT This manual and the appliance itself provide important safety messages, to be read and always observed. This is the danger symbol, regarding safety, warning of potential risks to users and others. All safety messages will be preceded by the danger symbol and the following words: DANGER Indicates a hazardous situation which, if not avoided, will cause serious injury.
- Do not pull the appliance power cable. - The electrical parts must not be accessible to the user after installation. - The appliance is designed solely for domestic use for cooking food. No other use is permitted (e.g. heating rooms). The Manufacturer declines any liability for inappropriate use or incorrect setting of the controls. - The appliance and its accessible components become hot during use. Be careful not to touch the heating elements.
- Do not place metal objects such as knives, forks, spoons and lids on the surface of the hob as they could overheat. - After use, switch the heating element off: do not rely on the automatic pan detection sensor (only for induction hobs). - This appliance must only be installed and used in a well-ventilated place, in accordance with the current regulations. Read the instructions carefully before installing and using this appliance.
Product description and symbols 1. Removable pan supports 2. Professional double crown Wok burners 3. 145 mm diameter induction zone 4. Left gas burner control knob 5. Central gas burner control knob 6. Right gas burner control knob 7. Display and touch control panel for the induction zones Gas burner control knob symbols A. Burner position indicator B. Flame regulation symbols - Off - Maximum external and internal crown flame B - Minimum external crown flame. Maximum internal crown flame.
Practical advice on how to use the burners Read these instructions to get the best out of your burners: - Use pans with a diameter the same as the burner (see pan diameter table to the side). - Only use flat bottom pots and pans. - Use the right amount of water for cooking food and use the lid. Important: using the pan supports incorrectly will scratch the hob top: avoid placing them upside down or dragging them across the hob.
Induction zone functions This hob is fitted with 2 induction zones that allow you to boil water very quickly, as well as control the temperature with extreme precision, giving you a vast range of cooking options. The induction zone control panel has the following functions. 1. 2. 3. 4. 5. 6. 7. The child safety option can be turned on by pressing the button (2) until the illuminated point above the button with the key symbol (2) comes on.
Induction zone functions The time remaining can also be changed by pressing the clock symbol button (4) at any time and using the +/- buttons (3) to alter the time. The light above the display will flash for 10 seconds, then the display will show the amended time remaining. When the programmed time expires a continuous double signal will be heard. If a zone has been programmed using the timer option when the time expires the zone and the zone indicator will automatically switch off.
Sizes and installation measurements (mm) NOTE: If a hood is installed above the hob, read the instructions for fitting the hood where it indicates the correct distances to be complied with. • The cooktop has to be set into a work top between 20 - 40 mm deep. • The distance between the lower face of the glass ceramic hob and the cupboard or separating panel must comply with the sizes shown in diagram “A”.
Safeguarding the environment Warning • The rubber protection stoppers under the grills could be swallowed by small children and cause suffocation. • After removing the pan supports, make sure that all the rubber stoppers are in place on the pan supports. • Each time you finish using the hob, always check that the control buttons are in the off position and shut off the tap to the gas mains or cylinder. • Do not obstruct the air vents at the back of the appliance in any way.
EC Declaration of conformity This appliance has been designed, constructed and marketed in compliance with: - safety requirements of "GAS" Directive 2009/142/EC (ex-90/396/EEC); - safety objectives of "Low Voltage" Directive 2006/95/EC (which replaces 73/23/EEC and subsequent amendments); - protection requirements of "EMC" Directive 2004/108/EC. This appliance is suitable for contact with foodstuffs and complies with EC Regulation no. 1935/2004.
Gas connection The gas mains system must comply with local regulations. • The paragraph on “national legislation reference” shows the local legislation specific to the country of destination. • Should there be no information regarding your country of interest, ask for further details from the installer.
Securing the hob into cabinetry 1. After cleaning the surfaces around the edges, fit the seal provided around the hob. 2. Position the hob inside the opening according to the sizes indicated in the description sheet. 3. Use the brackets (A) provided to secure the hob, fixing it with the proper screws to adapt it to the thickness. Warning: the electrical power cable must be long enough to allow the hob to be lifted out from above.
Replacing the injectors (See the product description sheet for model) Remove the bottom of the hob, lifting out the installation brackets to change the dual crown wok burner injector. Please contact the Customer Care Centre. REMOVING THE MAIN INJECTOR Remove the injector (F) using a 10mm spanner. Slacken the holding screw (H) to regulate the position (X) of the gas inlet coupling (G) with regard to the injector. REMOVING THE SECONDARY INJECTOR Remove the injector (I) using a 12 mm spanner.
General cleaning In order to keep your hob in good condition, you must keep it clean, removing any food residue each time you use it. Always disconnect the hob from the electrical power supply and wait until it cools before cleaning. Note: in the models fitted with electronic ignition and safety thermocouples, you have to clean the terminal part very carefully to ensure they work properly. Frequently check them and, if necessary, clean with a damp cloth.
Troubleshooting guide 3. If the hob does not work after intensive use, it means that the temperature inside the hob is too high. In this case E2 appears on the display. Wait for a few minutes until the hob cools down. 4. If the control shows that one or more of the buttons has been pushed in for too long, the symbol will appear. This message may also be the result of objects being improperly positioned on the control area, or left over food. Clean the control area carefully. 5.
After Sales Service Before contacting the Customer Care Centre, clarify that you cannot resolve the problem yourself based on the descriptions given in the “Troubleshooting guide”. 1. Turn the apparatus off and restart it to see if the fault is repeated. If after carrying out the above checks, the fault persists, contact your Customer Care Centre.
Whirlpool Europe S.r.l. Viale G. Borghi, 27 - 21025 Comerio (VA) Phone 0332.759111 - Fax 0332.759268 www.whirlpool.
