CONTENTS DEFINITION OF USE BEFORE USING THE WASHING MACHINE PRECAUTIONS AND GENERAL RECOMMENDATIONS DESCRIPTION OF THE WASHING MACHINE INSTALLATION ELECTRICAL CONNECTION BEFORE THE FIRST WASH CYCLE PREPARATION OF THE LAUNDRY DETERGENTS AND ADDITIVES CLEANING THE FILTER/ DRAINING RESIDUAL WATER CARE AND MAINTENANCE TROUBLESHOOTING GUIDE AFTER-SALES SERVICE TRANSPORT AND HANDLING
DEFINITION OF USE This washing machine is exclusively destined to wash and spin machine washable laundry in quantities which are usual for private households. • Observe the instructions given in these Instructions for Use and the Programme Chart when using the washing machine. • Keep these Instructions for Use and the Programme Chart; if you pass on the washing machine to another person, also give him/her Instructions for Use and Programme Chart. BEFORE USING THE WASHING MACHINE 1.
PRECAUTIONS AND GENERAL RECOMMENDATIONS 1. Safety instructions • The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. Disposal must be carried out in accordance with local environmental regulations for waste disposal.
INSTALLATION Removal of transport bracket The washing machine is fitted with a transport bracket to avoid any possible damage during transport. IMPORTANT: Before using the washing machine, the transport bracket at the back MUST be removed. A B 1. Unscrew the two screws “A” and the four screws “B” with a flat screwdriver or a No. 8 hex nut box spanner. 2. Remove the transport bracket. 3. Replace the four outer screws “B” on the machine and tighten them. 4.
Connect the water inlet hose 1. Carefully screw the water inlet hose to the valve on the rear side of the washing machine (“A”); screw the other end of the hose to the tap by hand. A 2. Make sure there are no kinks in the hose. 3. Check water-tightness of tap and washing machine connections by turning the tap completely on. If the hose is too short, replace it with a suitable hose available through our After-Sales Service or your specialist retailer. Periodically check the hose for brittleness and cracks.
ELECTRICAL CONNECTION Do not use extension leads or multi sockets. Electrical connections must be made in accordance with local regulations. 1) Warning - this washing machine must be earthed This washing machine is normally supplied with a mains lead having a plug fitted in the factory which has been checked for correct earth continuity.
BEFORE THE FIRST WASH CYCLE To remove any residual water used in testing by the manufacturer, we recommend that you carry out a short wash cycle without laundry. 1. Open the tap. 2. Close the drum flaps. 3. Add a small amount of detergent (maximum 1/3 of the quantity the detergent manufacturer recommends for lightly soiled laundry) to the main wash chamber of the detergent dispenser. 4. Close the lid. 5. Select and start programme “Synthetics” at 60°C (see separate the programme chart).
Loading the laundry 1. Open the machine lid by pulling it upwards. 2. Open the drum - by pushing the drum flap release (for “1a” and “1b”; models as shown on “1a” have a fixed drum flap release which will not compress when pushed). - by holding the rear drum flap, sliding back the slider into arrow direction and pushing the front flap towards the inside of the drum until the closing mechanism releases (for “1c”). 1a 1b 3. Place the items of laundry into the drum one by one.
DETERGENTS AND ADDITIVES Choice of the right detergents and additives: Dosage Follow the instructions on the detergent pack in relation to: - The degree and type of soiling. - The size of the load. Full load: follow the detergent manufacturer’s instructions; Half load: 3/4 the amount used for a full load; Minimum load (about 1 kg): half the amount used for a full load - Water hardness in your area (ask for information from your water company): soft water requires less detergent than hard water.
Using chlorine bleach Using starch powder • Wash your laundry in the desired programme (Cotton, Synthetics), adding an appropriate amount of chlorine bleach to the SOFTENER chamber (close the lid carefully). • Immediately after end of programme, start the “Rinse and Spin” programme to eliminate any residual bleach smell; if you want, you can add softener. • Never put both chlorine bleach and softener into the softener chamber at the same time.
CARE AND MAINTENANCE Detergent dispenser Clean the detergent dispenser regularly, at least three or four times a year, to prevent detergent build-up: 1. Push in the buttons on each side of the dispenser. 2. Pull the dispenser towards you and remove it. A small quantity of water can remain in the dispenser. It is advisable to carry the dispenser in an upright position. 3. Wash the dispenser using running water. You can also remove the siphon caps in the dispenser for cleaning. 4.
Appliance exterior and control panel Lid seal • Clean with a soft damp cloth. • Check the condition of the lid seal periodically and clean it from time to time with a damp cloth. • If necessary, a neutral household cleaner can be applied (do not use aggressive or abrasive products). Water inlet hose(s) • Check the hose regularly for brittleness and cracks. Replace if necessary. Appliance interior • After each washing, leave the lid open for some time to allow the inside of the appliance to dry.
TROUBLESHOOTING GUIDE Your washing machine is equipped with automatic safety functions which detect and diagnose faults at an early stage and allow you to react appropriately. These faults are frequently so minor that they can be removed within a few minutes. Problem Causes - Solutions - Tips Appliance does not start, no indicator lamps are on • Plug is not properly inserted in socket. • Socket or fuse does not function correctly (use a table lamp or similar appliance to test it).
Description of failure indications Failure indication lights up Description - Causes - Solutions Appliance has no or insufficient water supply. The “Start(Pause)” light flashes. “Water tap closed” Check whether: • Water tap is fully open and water supply pressure is sufficient. • Kinks are present in water inlet hose. • Mesh filter of water supply hose is blocked (see “Care and Maintenance”). • Water hose is frozen up.
Failure indication lights up Indication on display (if fitted on your machine) Appliance stops during the programme. “bdd” (in case your washing machine has no display: all lamps of the programme sequence indicator light up) “Drum flaps open” (the drum flaps have not been closed properly). Push the “Reset” button for at least 3 seconds and wait until the “Door open” lights up. Open lid and close drum flaps, then select and start desired programme again. If fault persists, notify our After-Sales Service.
AFTER-SALES SERVICE Before contacting After-Sales Service: Specify: 1. Try to remedy the problem yourself (see “Troubleshooting Guide”). • The nature of the problem. • The exact model of the washing machine. • The service code (number after the word SERVICE). 2. Restart the programme to check whether the problem has solved itself. 3. If the machine continues to function incorrectly, call After-Sales Service.