User Manual www.whirlpool.
Quick Guide EN THANK YOU FOR PURCHASING A WHIRLPOOL PRODUCT. Before using the appliance carefully read the Health and Safety guide. To receive more comprehensive assistance, register the appliance on www.whirlpool.eu/register Before using the machine, it is imperative that the transport bolts are removed. For more detailed instructions on how to remove them, see the Installation Guide. CONTROL PANEL 1. ON/OFF button 2. DRYING button 3. DRYING ONLY button 4. MULTI RINSE button 5. OPTION button 6.
WASH CYCLES Follow the instructions on the symbols of the garment’s wash care label. The value indicated in the symbol is the maximum recommended temperature for washing the garment. Daily Mix Wash & Dry use programme 1 to wash and dry mixed garments (cotton and synthetics). This cycle may be used to wash and dry loads of up to 3,5 kg; we recommend the use of liquid detergent. The use of the steam in this programme is optimised to reduce the formation of creases on garments, making them easier to iron.
CHANGING A RUNNING WASH CYCLE KEY LOCK To change a wash cycle while it is in progress, pause the washing machine using the START/PAUSE button (the relative indicator light will flash amber), then select the desired cycle and press the START/PAUSE button again. ! To cancel a cycle that has already begun, press and hold the ON/OFF button. The cycle will be stopped and the machine will switch off. To activate the control panel lock, press and hold the button for roughly 2 seconds.
TROUBLESHOOTING Your washing machine could occasionally fail to work. Before contacting the Technical Assistance Service, make sure that the problem cannot be easily solved using the following list. Anomalies Possible causes / Solution The washer-dryer does not start. The appliance is not plugged into the socket fully, or not enough to make contact. There is no power in the house. The washing machine door is not closed properly. The ON/OFF button has not been pressed. The wash cycle does not start.
CLEANING & MAINTENANCE For any cleaning and maintenance, switch off and unplug the washing machine. Do not use flammable fluids to clean the washing machine. CLEANING THE OUTSIDE OF THE WASHING MACHINE Use a soft damp cloth to clean the outer parts of the washing machine. Do not use glass or general purpose cleaners, scouring powder or similar to clean the control panel – these substances might damage the printing. CHECKING THE WATER SUPPLY HOSE Check the inlet hose regularly for brittleness and cracks.
CLEANING THE DETERGENT DISPENSER Remove the dispenser by raising it and pulling it out (see figure). Wash it under running water; this operation should be repeated frequently. 1 2 CLEANING THE WATER FILTER / DRAINING RESIDUAL WATER Switch off and unplug the washing machine before cleaning the water filter or draining residual water. If you used a hot wash programme, wait until the water has cooled down before draining any water.
TRANSPORT AND HANDLING Never lift the washing machine by holding it at the worktop. 1. Pull out the mains plug, and close the water tap. 2. Make sure that door and detergent dispenser are properly closed. 3. Disconnect the inlet hose from the water tap, and remove the drain hose from your draining point. Remove all rest water from the hoses, and fix them so that they cannot get damaged during transport. 4. Refit the transport bolts.
10 mm - 0,39 inch 3. 2. 1. 150 ml 100 ml 50 ml 4. 2 cm - 0,7 inch 6. 5. 7.
8. 9. max 0,5 cm max 0,2 inch 10. 11. 12. max 100 cm 39 inch min 65 cm 25 inch max 100 cm 39 inch min 65 cm 25 inch max 100 cm 39 inch min 65 cm 25 inch 13. 14.
SAFETY INSTRUCTIONS EN IMPORTANT TO BE READ AND OBSERVE used as specified by the fabric softener instructions. The final part of a tumble dryer cycle occurs without heat (cool down cycle) to ensure that the items are left at a temperature that ensures that the items will not be damaged. Never stop a tumble dryer before the end of Very young children (0-3 years) should be kept the drying cycle unless all items are quickly away from the appliance.
Do not install your appliance where it may be exposed to extreme conditions, such as: poor ventilation, temperatures below 5 °C or above 35 °C. When installing the appliance make sure that the four feet are stable and resting on the floor, adjusting them as required, and check that the appliance is perfectly to level using a spirit level.
