INSTALLATION INSTRUCTIONS UNDERCOUNTER DISHWASHER PLASTIC TUB INSTRUCCIONES DE INSTALACIÓN LAVAVAJILLAS EMPOTRADA CON TINA PLÁSTICA INSTRUCTIONS D’INSTALLATION LAVE-VAISSELLE ENCASTRÉ CUVE EN PLASTIQUE Table of Contents........................................................2 Indice ........................................................................27 Table des matières ....................................................
TABLE OF CONTENTS DISHWASHER SAFETY ................................................... 3 INSTALLATION REQUIREMENTS ................................... 4 Tools and Parts .........................................................................4 Location Requirements .............................................................6 Product and Cabinet Opening Dimensions ..............................7 Drain Requirements ..................................................................
DISHWASHER SAFETY Your safety and the safety of others are very important. We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages. This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.
INSTALLATION REQUIREMENTS TOOLS AND PARTS Other Useful Items You May Need: Gather the recommended tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.
Other Parts Needed (not provided): 3 /8" Compression x 3/4" Hose Fitting with rubber seal and 90° elbow (required to properly connect household water line to the dishwasher) (Whirlpool Part Number W10685193) Household Wiring (Metallic) Strain Relief to fit 7/8" (22 mm) hole (required to properly secure household wiring to the dishwasher terminal box) (Whirlpool Part Number 4396672) First-Time Installations Check local codes. Check existing electrical supply. See the “Electrical Requirements” section.
For Direct Wire For Power Cord LOCATION REQUIREMENTS Dishwasher must be fully enclosed (top, sides, back, and floor) upon installation. A side panel kit is available from your dealer for installing your dishwasher at the end of your cabinetry. An optional moisture barrier accessory is also available for installing underneath a wooden countertop. See the “Tools and Parts” section at the front of the guide for part details and orders. Check location where dishwasher will be installed.
PRODUCT AND CABINET OPENING DIMENSIONS 251/4" (641 mm) 3/4" (19 mm) A B 30" (762 mm) 33/4" (94 mm) 21" (533 mm) For 4" (100 mm) toe kick, height of cabinet opening is 341/2" (863 mm). A. Insulation may be compressed (not used on all models). B. Door handles may protrude forward of the face of the dishwasher, (varies by model). Check that all surfaces have no protrusions that would prohibit dishwasher installation.
DRAIN REQUIREMENTS ■ ■ ■ A new drain hose is supplied with your dishwasher. If drain hose is not long enough, use a new drain hose with a maximum length of 12 ft (3.7 m) that meets all current AHAM/ IAPMO test standards, is resistant to heat and detergent, and fits the 1" (25 mm) drain connector of the dishwasher. See the “Tools and Parts” section at the front of the guide for part details and orders.
INSTALLATION INSTRUCTIONS 4. WARNING Sand holes smooth Wood cabinet Electrical Shock Hazard Metal cabinet Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. Failure to do so can result in death or electrical shock. 1. Disconnect power Wood cabinet: Sand the hole until smooth. Disconnect electrical power at the fuse box or circuit breaker box before installing dishwasher. 2.
5. Built-up floors – add shims as needed ELECTRICAL CONNECTION – For Direct Wire, begin with Step 7 – For Power Cord, wait until Step 22 7. Built-up floors: If the kitchen floor is higher than the cabinet opening’s floor – for example, the kitchen floor tile does not extend into the cabinet opening – add shims, as needed, in the area shown to bring the dishwasher up to 34" (864 mm) below the countertop. NOTE: Shims must be securely attached to floor to avoid movement when the dishwasher is in use. 6.
PREPARE DISHWASHER WARNING REMOVE ACCESS PANEL – For Plastic Access Panels, go to Step 9 – For Metal Access Panels, go to Step 10 9. Plastic panel Tip Over Hazard Do not use dishwasher until completely installed. Do not push down on open door. Doing so can result in serious injury or cuts. 1 4 / turn WARNING Excessive Weight Hazard Use two or more people to move and install dishwasher. Failure to do so can result in back or other injury. 8.
NOTE: If the minimum cabinet opening height is less than 337/8" (860 mm), the rear leveling legs and spacers can be removed for additional clearance. This will allow the dishwasher to fit into a 331/2" (851 mm) high cabinet opening, but the dishwasher will be more difficult to move. (Measurements are approximate. Rear and front leveling legs are preset at the factory for 341/2" [876 mm].) 11. Measure cabinet opening 12.
CONNECT WATER LINE TO FILL VALVE – For Copper Line, begin with Step 14 – For Flexible Line, begin with Step 16 16. Flexible line 14. Copper water line Flexible braided line: Confirm the flexible braided line is long enough. See the “Tools and Parts” section at the front of the guide for part details and orders. If using copper tubing, measure overall length of copper tubing required to reach the water supply, cut to length, and attach with compression fittings. 17.
DRAIN HOSE CONNECTION POWER CORD CONNECTION NOTE: If removing a previous dishwasher with a power cord, you will need to transfer the power cord to the new dishwasher. 19. Connect drain hose 22. Remove terminal box cover Small clamp Rubber drain hose connector Drain hose Drain hose stop Stop Stop Place towel under drain hose to catch any water in drain hose. Place the small (green) drain hose clamp onto the small end of the drain hose.
WARNING Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Wiring configuration 27. Power cord – secure cord in strain relief Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 25. Power cord – connect ground wire Tighten strain relief screws to secure cord. Ground wire 28.
INSTALL DOOR HANDLE IMPORTANT: If wheels were removed, cover the floor when moving the dishwasher. Slowly move dishwasher completely into cabinet opening. Do not kink or pinch water line, drain hose, power cord, or direct wire between dishwasher and cabinet. Remove cardboard from under dishwasher. (ON SOME MODELS) 29. Install door handle Mounting stud Handle It is all right if dishwasher fits tightly into cabinet opening. Do not remove insulation blanket – the blanket reduces the sound level.
34. Move dishwasher all but 6" (152 mm) into cabinet opening Countertop Attachment: 36. Insert bracket 6" (152 mm) Tabs must point to the right. NOTE: Leave unit about 6" (152 mm) out from cabinet in order to install anchor brackets and adjust door tension if needed. 35. Pull slack from utilities NOTE: Pull slack out of utilities at the same time the dishwasher is pushed into the cabinet opening to avoid any kinks.
38. Install bracket 41. Door falls open – increase spring tension Bend tabs Push bracket into slot on the side of dishwasher and bend tab in toward the side of the dishwasher so that it keeps the bracket in place. Repeat this step for the other side of the dishwasher. NOTE: Install wood shims to the inside of the cabinets if the gap between the sides of the cabinet and the sides of the dishwasher are greater than 1/2" (13 mm) on each side. NOTE: Do not attach the dishwasher. This will be done later.
SECURE DISHWASHER IN CABINET OPENING Level legs Preferred method Optional method 45. Double-check dishwasher alignment in cabinet opening 44. Check level side to side and adjust legs if needed Check that dishwasher is still level front to back and side to side in the cabinet opening. Open dishwasher door and place towel over pump assembly and spray arm of dishwasher. This will keep screws from falling into pump area when you are securing dishwasher to countertop or cabinet. 46.
47. Check door clearance IMPORTANT: Check that top of door does not contact screws, brackets, or countertop. If it does, adjust leveling legs or use the side attachment option. 48. Check inner spacing Open door and check that space between dishwasher cabinet opening, and tub is equal on both sides. If spacing is not equal, loosen bracket screws and shift tub. Tighten bracket screws. DIRECT WIRE CONNECTION 49.
WARNING Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Wiring configuration 54. Direct wire – secure cable in strain relief Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. 52. Direct wire – connect ground wire Ground screw Ground wire Tighten strain relief screws to secure cable. 55.
CONNECT WATER LINE TO HOUSE SHUT-OFF VALVE Option A: Waste disposer – no air gap NOTE: If using a flexible braided hose, replace inlet hose after 5 years to reduce the risk of hose failure. Record hose installation or replacement dates on the hose for future reference. Large drain hose clamp Disposer inlet Drain hose 56. Attach water supply line Drain trap Helpful Tip: Remove disposer knockout plug.
Option B: No waste disposer – no air gap Option C: Waste disposer – with air gap Air gap Screw-type clamps Large drain hose clamp Waste tee Large drain hose clamp Disposer inlet Drain hose Rubber hose connector Drain hose Drain trap Drain trap 1 1. Fit rubber end of drain hose to waste tee and cut if needed. NOTE: Do not cut ribbed section. Helpful Tip: Remove disposer knockout plug. 1 1. Using a hammer and screwdriver, knock plug into disposer. Rubber end 2 2.
Option D: No waste disposer – with air gap COMPLETE INSTALLATION Check that the power supply wire or cord does not touch dishwasher motor or the lower part of the dishwasher tub. Air gap Screw-type clamps Large drain hose clamp Waste tee Rubber hose connector Drain hose Drain trap 1 Rubber end 2 3 1. Connect rubber end of drain hose to air gap and cut if needed. NOTE: Do not cut ribbed section. 2. Attach drain hose to air gap with large drain hose clamp (provided).
INSTALL ACCESS PANEL – For Plastic, begin with Step 60 – For Metal, begin with Step 63 Metal Panel: 63. Reinstall access panels Plastic Panel: 60. Reinstall access panel and fasteners Insulation (on some models) Place the panel against dishwasher legs. Using a Phillips screwdriver or 1/4" nut driver, reinstall the screws through the holes in the access panel. Place the plastic access panel against the dishwasher leg. Make sure insulation does not interfere with the float assembly. 64.
CHECK OPERATION ADDITIONAL TIPS Read the dishwasher User Guide that came with your dishwasher. ■ Check that all parts have been installed and no steps were skipped. Check that you have all tools used. If the dishwasher is not working properly, disconnect power or unplug dishwasher and refer to the “If Dishwasher Does Not Operate” section. Expect longer wash times. Your new dishwasher will average 2-5 hours per load but use nearly 40% less energy than older models.
