Owner's Manual
Table Of Contents
- RANGE SAFETY
- Range Safety
- RANGE MAINTENANCE AND CARE
- General Cleaning
- Clean Cycle
- INSTALLATION INSTRUCTIONS
- REQUIREMENTS
- Tools and Parts
- Location Requirements
- Electrical Requirements
- Gas Supply Requirements
- INSTALLATION
- Unpack Range
- Install Anti-Tip Bracket
- Make Gas Connection
- Install Griddle (on some models)
- Verify Anti-Tip Bracket Is Installed and Engaged
- Level Range
- Electronic Ignition System
- Warming Drawer or Premium Storage Drawer (on some models)
- Oven Door
- Complete Installation
- GAS CONVERSIONS
- Propane Gas Conversion
- Natural Gas Conversion
- Moving the Range
- SÉCURITÉ DE LA CUISINIÈRE
- Sécurité de la cuisinière
- ENTRETIEN ET RÉPARATION DE LA CUISINIÈRE
- Nettoyage général
- Programme de nettoyage
- INSTRUCTIONS D’INSTALLATION
- EXIGENCE
- Outils et pièces
- Exigences d’emplacement
- Spécifications électriques
- Spécifications de l’alimentation en gaz
- INSTALLATION
- Déballage de la cuisinière
- Installation de la bride antibasculement
- Raccordement au gaz
- Installation de la plaque à frire (Sur certains modèles)
- Vérifier que la bride antibasculement est bien installée et engagée
- Réglage de l’aplomb de la cuisinière
- Système d’allumage électronique
- Tiroir-réchaud ou tiroir de remisage de qualité supérieure (sur certains modèles)
- Porte du four
- Achever l’installation
- CONVERSIONS POUR CHANGEMENT DE GAZ
- Conversion pour l’alimentation au propane
- Conversion pour l’alimentation au gaz naturel
- Déplacement de la cuisinière
- SEGURIDAD DE LA ESTUFA
- Seguridad de la estufa
- CUIDADO Y MANTENIMIENTO DE LA ESTUFA
- Limpieza general
- Ciclo de limpieza
- INSTRUCCIONES DE INSTALACIÓN
- REQUISITOS
- Herramientas y piezas
- Requisitos de ubicación
- Requisitos eléctricos
- Requisitos de suministro de gas
- INSTALACIÓN
- Desembale la cocina
- Instalación del soporte antivuelco
- Conexión del suministro de gas
- Instalación de la plancha (en algunos modelos)
- Verifique que el soporte anti-vuelco esté instalado y enganchado
- Nivelación de la cocina
- Sistema de encendido electrónico
- Cajón de calentamiento o cajón de almacenamiento premium (en algunos modelos)
- Puerta del horno
- Completar la instalación
- CONVERSIONES DE GAS
- Conversión a gas propano
- Conversión a gas natural
- Cómo mover la estufa
18
If the “low” flame needs to be adjusted:
A. Control knob stem
B. Screwdriver
C. Pliers
1. Light 1 burner and turn to lowest setting.
2. Remove the control knob.
Hold the knob stem with a pair of pliers. Use a small flat blade
screwdriver to turn the screw located in the center of the
control knob stem until the flame is the proper size.
3. Replace the control knob.
4. Test the flame by turning the control from “LO” to “HI”,
checking the flame at each setting.
5. Repeat the previous steps for each burner.
Check Operation of Oven Bake Burner
1. Remove the oven rack.
2. To remove the oven bottom: Remove 2 screws at the rear of
the oven bottom. Lift the rear of the oven bottom up and back
until the front of the panel is away from the front frame.
Remove it from oven and place on a covered surface.
A. Screws
B. Oven bottom
3. You can check the burner flame by using a mirror. Insert a
mirror to one side of the burner. Look into the mirror to check
flame.
4. Push the BAKE pad.
5. Press the START pad.
The oven bake burner should light within 8 seconds. Under certain
conditions, it may take the burner up to 50 to 60 seconds to light.
Electronic igniters are used to light the bake and broil burners.
Refer to the Quick Start Guide and online Control Guide for proper
operation of the oven controls.
Adjust Oven Bake Burner Flame (if needed)
1. On models with a warming drawer, remove access cover plate
(1 screw) located at the back of the warming drawer
compartment.
2. Check the oven bake burner for proper flame.
This flame should have a 1/2" (1.3 cm) long inner cone of
bluish-green, with an outer mantle of dark blue, and should be
clean and soft in character. No yellow tips, blowing or lifting of
flame should occur.
3. If the oven bake flame needs to be adjusted, locate the air
shutter near the center rear of the range. Loosen the locking
screw and rotate the air shutter until the proper flame appears.
Tighten locking screw.
A. Locking screw
B. Air shutter
4. Push CANCEL/OFF when finished.
5. Reinstall flame spreader and oven bake burner cover.
Check Operation of Oven Broil Burner
1. Close the oven door.
2. Press the BROIL pad.
3. Press the START pad.
The oven burner should light within 8 seconds. Under certain
conditions, it may take the burner up to 50 to 60 seconds to light.
Refer to the Quick Start Guide and online Control Guide for proper
operation of the oven controls.
Adjust Oven Broil Burner Flame (if needed)
Look through oven window to check broil burner for proper flame.
This flame should have a 1/2" (1.3 cm) long inner cone of bluish-
green, with an outer mantle of dark blue, and should be clean and
soft in character. No yellow tips, blowing or lifting of flame should
be present.
If flame needs to be adjusted:
1. Loosen the lock screw on the air shutter located at the rear of
the broil burner.
2. Adjust the air shutter as needed.
3. Tighten lock screw.
A. Lock screw
B. Air shutter
4. Press CANCEL/OFF when finished.