Use and Care

6
Sensing
When Start/Pause is touched the washer will chime,
indicating it is starting. The drum will make a partial turn.
The door will click when it locks.
Once the door has locked, the washer will begin spinning
to sense the load size. This sensing process will continue
throughout the cycle.
After the load size is sensed, the estimated time based
on load size will be displayed and water will be added.
You may hear water owing through the dispenser,
adding detergent to the load. The actual cycle time may
be lengthened; however, the display will continue to show
the estimated time.
Washing
During the wash cycle, this will display to let you know
the cycle is in progress.
Drying (on some models)
During a drying cycle, this will display to let you know
the drying cycle is in progress.
PreSoak
This symbol will be displayed to let you know
a presoak is in progress.
Detergent Low (on some models)
When detergent in the bulk dispenser is running low,
the display will show the detergent level (Low).
Add Garment
When “Add Garment” is displayed, you may pause the
washer, open the door, and add items. Touch and hold
START/PAUSE to start the washer again.
Door Locked
The Door Locked symbol will display to indicate
that the door is locked and cannot be opened
without rst pausing or canceling the cycle.
Control Lock
When the Contol Lock symbol is displayed,
the buttons are disabled. Touch and hold
EXTRA RINSE for three seconds to enable the
buttons.
FanFresh
®
(on some models)
This symbol will be displayed when the FanFresh
®
option is activated. The fan will turn on and the
load will tumble periodically for up to 12 hours.
End
Once the cycle is complete, “End” will display. Remove
the load promptly for best results.
CYCLE MODIFIERS
When you select a cycle, its default settings will light up.
Touch to adjust cycle modiers on the washer before
touching START/PAUSE. Additional wash modiers or
options selected after touching Start/Pause may not activate.
Once a wash setting is selected, it is saved for the cycle
selected. To return to factory default cycle settings, unplug
washer for 30 seconds; then plug back in. See “Cycle Guide”
for default cycle settings.
NOTE: Some modiers may increase or decrease the
estimated time remaining.
hold 3 sec for
Cycle Signal
hold 3 sec for
Control Lock
hold 3 sec for
FanFresh
hold 3 sec for
PreSoak
5
Temp
The recommended wash temperature is preset for
each cycle. Some preset temperatures can be changed.
You may select a different wash temperature based on
the level of soil and type of fabric being washed. For
best results, use the warmest wash water safe for your
fabric, following the garment label instructions. All wash
temperatures feature a cold rinse.
Spin
The recommended spin speed is preset for each cycle.
Some preset speeds can be changed.
■ Faster spin speeds mean shorter dry times, but may
increase wrinkling in your load.
■ Slower spin speeds reduce wrinkling, but will leave
your load more damp.
Soil
The recommended soil level is preset for each cycle.
Some preset soil levels can be changed. For heavily
soiled and sturdy fabrics, select the Heavy Soil Level
setting. For lightly soiled and delicate fabrics, select the
Light Soil Level setting. Lower soil level settings will help
reduce tangling and wrinkling.
UTILITY CYCLES
Clean Washer
Use this every 30 washes to keep the inside of your
washer fresh and clean. This cycle uses a higher water
level. Use with affresh
®
Washer Cleaner tablets or liquid
chlorine bleach to thoroughly clean the inside of your
washer. When using this cycle, the drum should be
empty. This cycle should not be interrupted. See the
“Washer Care” section.
Drain & Spin
This cycle removes excess water from the load or
special-care items washed by hand. Use this cycle
after a power failure. For some fabrics, you may choose
to set a slower spin speed.
CYCLE OPTIONS
You may add or remove options for each cycle. Not all
options can be used with all cycles, and some are preset
to work with certain cycles. Options vary by model.
Steam Clean (on some models)
The Steam Clean option adds additional soak and
wash time to many cycles to help remove tough stains,
as well as a steam boost for added cleaning power.
An integrated heater helps to maintain optimal wash
temperatures. See “Cycle Guide” for cycles that allow
the Steam Clean option.
You can also touch and hold STEAM CLEAN
for three seconds to turn cycle signals on or off.
Extra Rinse
Activate this option to add an extra rinse to most
cycles.
You can also touch and hold EXTRA RINSE
for three seconds to disable/enable the Control Lock.
Wash & Dry (on some models)
Touch to add a drying cycle to your load after the wash
cycle has nished. The Wash & Dry option is designed
to wash and dry small loads overnight. This option is
design for 2-4 lightly soiled synthetic garments, athletic
uniforms, or workout wear. This option has an extra-
high-speed spin followed by intermittent tumbling and
fan activation to circulate air through the clothes.
6
7